journal article·2025-03-11Open access

Friction Behavior of Molybdenum Disulfide/Polytetrafluoroethylene-Coated Cemented Carbide Fabricated with a Spray Technique in Dry Friction Conditions

Li Zhang, Wenlong Song

Coatings· Volume 15· Issue 3

Abstract

Cemented carbide has a relatively high surface friction coefficient, which can result in increased wear and energy consumption during friction, ultimately impacting service life and efficiency. In order to improve the tribological properties of the traditionally cemented carbide, the MoS2 and PTFE (25 wt.%) mixed powders, which were blended with Polyamide-imide (PAI) as the adhesive, were sprayed on the carbide surface at 70 °C. Tests were used to measure the performance of MoS2/PTFE-coated carbide, such as surface micrographs and cross-section micrographs, surface roughness, adhesion strength between coatings and substrate, and surface microhardness. Sliding friction tests were performed to investigate the friction performance. The test results showed that the adhesion strength between the coatings and substrate was up to 36 N, the hardness was about 0.42 GPa, and the friction coefficient was reduced by about 70%. The lower shear strength of MoS2/PTFE coatings led to the reduction of friction and wear. The main wear mechanisms of MoS2/PTFE coatings were surface abrasion and coating flaking. The MoS2/PTFE coatings present a promising approach to enhance the friction performance of traditional cemented carbide.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Metal and Thin Film Mechanics · Tribology and Wear Analysis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Mechanical and Electrical Engineering, Jining University, Qufu 273155, China

Funding

Key Research and Development Program of Jining, China · Science and Technology Innovation Team Foundation of Jining University · Scientific Research Foundation of Jining University

References (31)

Show source-provided references
1. Enhancing the machining performance by cutting tool surface modifications: A focused review10.1080/10910344.2019.1575412 ↗
2. Wear reduction mechanisms in modulated turning of compacted graphite iron with coated carbide tool10.1016/j.triboint.2022.108062 ↗
3. High temperature sliding wear behavior and mechanisms of cold-sprayed Ti and Ti-TiC composite coatings10.1016/j.wear.2021.203746 ↗
4. Insights in α-Al2O3 degradation in multilayer CVD coated carbide tools when turning IN71810.1016/j.wear.2023.204786 ↗
5. On chemical interactions between an inclusion engineered stainless steel (316L) and (Ti,Al)N coated tools during turning10.1016/j.wear.2023.205093 ↗
6. Machining performances of TiN+AlCrN coated WC and Al2O3+TiC inserts for turning of AISI 4140 steel under dry condition10.1016/j.jmapro.2019.12.057 ↗
7. Achieving clean production with nanostructured coated milling tools dry machining low carbon steel10.1016/j.jclepro.2023.138523 ↗
8. Evaluation of tool wear mechanisms and tool performance in machining single-phase tungsten10.1016/j.ijrmhm.2020.105379 ↗
9. Wear behavior of AlTiN coated WC tools in micromilling of Ti6Al4V alloy using vegetable oil-based nanofluids10.1016/j.triboint.2023.108825 ↗
10. Influence of V concentration in TiAlSiVN coating on self-lubrication, friction and tool wear during two-pass dry turning of austenitic steel 316L10.1016/j.triboint.2024.109355 ↗
11. The effect of atmosphere on the tribological behavior of magnetron sputtered MoS2 coatings10.1016/j.surfcoat.2019.125081 ↗
12. Preparation and tribological properties of MoS2-based multiple-layer structured films fabricated by electrohydrodynamic jet deposition10.1016/j.surfcoat.2020.125334 ↗
13. Nano-mechanical and nano-tribological characterisation of self-lubricating MoS2 nano-structured coating for space applications10.1016/j.triboint.2022.108017 ↗
14. Performance of CrCN-WS2 hard/soft composite coated tools in dry cutting of titanium alloys10.1016/j.jmapro.2020.03.014 ↗
15. Metal cutting lubricants and cutting tools: A review on the performance improvement and sustainability assessment10.1007/s00170-019-04890-w ↗
16. Ultra-low friction of polyethylenimine/molybdenum disulfide (PEI/MoS2)15 thin films in dry nitrogen atmosphere and the effect of heat treatment10.1016/j.triboint.2018.06.003 ↗
17. LIPSS combined with ALD MoS2 nano-coatings for enhancing surface friction and hydrophobic performances10.1016/j.surfcoat.2020.125396 ↗
18. In vacuo tribological behavior of polytetrafluoroethylene (PTFE) and alumina nanocomposites: The importance of water for ultralow wear10.1007/s11249-013-0256-1 ↗
19. A novel structured suspension plasma sprayed YSZ-PTFE composite coating with tribological performance improvement10.1016/j.surfcoat.2018.11.021 ↗
20. Tribological properties of MoS2 coating for ultra-long wear-life and low coefficient of friction combined with additive g-C3N4 in air10.1007/s40544-020-0374-3 ↗
21. Friction and wear behavior of PTFE coatings modified with poly (methyl methacrylate)10.1016/j.compositesb.2019.04.047 ↗
22. Advances in development of solid lubricating MoS2 coatings for space applications: A review of modeling and experimental approaches10.1016/j.triboint.2023.109194 ↗
23. Tribological performance of graphene and PTFE solid lubricants for polymer coatings at elevated temperatures10.1007/s11249-019-1212-5 ↗
24. Tribological performance of AlCrN-MoS2/PTFE hard-lubricant composite coatings10.1177/1350650119878564 ↗
25. Nanocomposite and nanostructured tribological materials for space applications
26. Core-shell structure polydopamine and polyethylenimine co-assisted MoS2-BaTiO3/polyarylene ether nitrile nanocomposites for high-temperature resistant organic dielectrics10.1016/j.jallcom.2023.173336 ↗
27. Friction behavior of TiN-MoS2/PTFE composite coatings in dry sliding against SiC10.1016/j.ceramint.2021.05.109 ↗
28. The wear and lubrication performance of liquid-solid self-lubricated coatings10.1016/j.surfcoat.2013.07.063 ↗
29. Song, W.L., Xia, Z.X., Wang, S.J., and Zhang, Q.G. (2020). Effect of Zr target current on the mechanical and tribological performance of MoS2-Zr composite lubricating coatings. Coatings, 10.10.3390/coatings10010080 ↗
30. Tribological performance of DLC-coated ceramics against cemented carbide under dry sliding conditions10.1016/j.ceramint.2021.03.003 ↗
31. Wen, S.Z. (2017). Principle of Tribology, Tinghua University Press.