Effect of Co/TiAl on Mechanical Properties of Laser Melted IN 625 on 304SS Matrix
Source abstract
Abstract
IN 625 is one of the most widely used nickel-based high-temperature alloys. However, the unstable high-temperature mechanical properties of IN625 and the difficulty of processing complex parts have limited its wider application. This work fabricated IN625 coatings with Co/TiAl (1.25, 1.55, and 1.85) on 304SS using laser melting deposition technology, with excellent high-temperature mechanical properties. The effects of Co/TiAl on the microstructure and properties of the laser-cladded resulting coatings have been carefully investigated. Compared to the IN625 coating, the addition of Co, Ti, and Al to the IN625 laser cladding coating significantly enhances its hardness and strength at room temperature, while reducing the elongation rate sharply. After heat treatment (900 °C × 10 h + 850 °C × 2 h), the hardness of the IN625 coating decreases, while the hardness of the IN625 laser cladding coating with added Co, Ti, and Al significantly increases. At a temperature of 850 °C, the yield strength and elongation rate of the IN625 laser cladding coating with Co, Ti, and Al additives exhibit an increasing-then-decreasing trend as the Co/TiAl ratio rises. The results exhibited that the coating had excellent high-temperature mechanical properties when the Co/TiAl is 1.55, and its hardness, tensile strength, yield strength, and elongation rate are 48.62 HRC, 735 Map, 665 MPa, and 11.3%, respectively.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · High Entropy Alloys Studies · High Temperature Alloys and Creep
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Mechanical Engineering, University of South China, Hengyang 421200, China
College of Mechatronics and Control Engineering, Additive Manufacturing Institute, Shenzhen University, Shenzhen 518000, China
Funding
National Key Research and Development Program · National Defense Science and Technology Key Laboratory Fund Project · National Defense Science and Technology Advanced Research Fund Project · Hunan Province postgraduate research and innovation project
References (44)
Show source-provided references
1. Effect of heat treatment on microstructure and oxidation properties of Inconel 625 processed by LPBF10.1016/j.jallcom.2020.156418 ↗
2. Effect of B4C nanoparticles on microstructure and properties of laser cladded IN625 coating10.1016/j.surfcoat.2021.127154 ↗
3. The role of texturing and microstructure evolution on the tensile behavior of heat-treated Inconel 625 produced via laser powder bed fusion10.1016/j.msea.2019.138500 ↗
4. Microstructures and mechanical behavior of the bimetallic additively-manufactured structure (BAMS) of austenitic stainless steel and Inconel 62510.1016/j.jmst.2020.10.001 ↗
5. A review on additive manufacturing processes of inconel 62510.1007/s11665-021-06427-3 ↗
6. High-temperature mechanical properties of nickel-based superalloys manufactured by additive manufacturing10.1080/02670836.2020.1799137 ↗
7. Microstructural evolutions during thermal aging of alloy 625: Impact of temperature and forming process10.1007/s11661-014-2256-7 ↗
8. Decoupling build orientation-induced geometric and texture effects on the mechanical response of additively manufactured IN625 thin-walled elements10.1016/j.msea.2023.144826 ↗
9. Tian, Z., Zhang, C., Wang, D., Liu, D., and Tian, Y. (2019). A review on laser powder bed fusion of inconel 625 nickel-based alloy. Appl. Sci., 10.10.3390/app10010081 ↗
10. Effect of scanning speed on the high-temperature oxidation resistance and mechanical properties of Inconel 625 alloys fabricated by selective laser melting10.1016/j.vacuum.2022.111447 ↗
11. Comparison the machinability of Inconel 718, Inconel 625 and Monel 400 in hot turning operation
12. Improvement of fatigue performance of laser powder bed fusion fabricated IN625 and IN718 superalloys via shot peening10.1016/j.jmatprotec.2022.117571 ↗
13. Influence of an aluminizing process on the microstructure and tensile strength of the nickel superalloy IN 718 produced by the Selective Laser Melting10.1016/j.vacuum.2020.110041 ↗
14. Binder jetting of “Hard-to-Weld” high gamma prime nickel-based superalloy RENÉ 108
15. Microstructural evolution and mechanical properties of selective laser melted a nickel-based superalloy after post treatment10.1016/j.msea.2020.139649 ↗
16. Thermal barrier coatings-A state of the art review10.1007/s12540-020-00705-w ↗
17. High temperature tensile and fatigue behaviors of additively manufactured IN625 and IN71810.1016/j.prostr.2022.03.059 ↗
18. Effects of non-equilibrium microstructures on microstructure evolution and mechanical properties of laser powder bed fusion IN625 Ni-based superalloy during long-term thermal exposure at 700 °C and 750 °C10.1016/j.msea.2022.143883 ↗
19. Elevated temperature mechanical behavior of IN625 alloy processed by laser powder-bed fusion10.1016/j.msea.2017.06.045 ↗
20. The creep and fracture properties of additively manufactured inconel 62510.1016/j.mtla.2021.101021 ↗
21. Formative and controlled mechanisms of nano-sized γ′ precipitates with local phase-transition within dislocation networks of nickel-based single crystal superalloys10.1016/j.actamat.2021.116653 ↗
22. Influence behavior and mechanism of γ′-or γ′′-precipitated phase types on damage resistance of heterogeneous interface in nickel-based superalloys10.1016/j.jallcom.2022.166559 ↗
23. Correlation between secondary γ′ and high-temperature tensile behavior of a powder metallurgy nickel-based superalloy EP962NP10.1016/j.msea.2023.144687 ↗
24. Alloying-element dependence of structural, elastic and electronic properties of nickel-based superalloys: Influence of γ′volume fraction10.1016/j.jallcom.2020.155141 ↗
25. Precipitation and phase transformation mechanism of additive manufactured Ni-Co base superalloy10.1016/j.matchar.2019.03.015 ↗
26. Influence of Co content on the microstructures and mechanical properties of a Ni–Co base superalloy made by specific additive manufacturing process10.1016/j.msea.2020.139438 ↗
27. Phase constituents in Ni–Al–Co–Ti quaternary alloys10.1016/j.intermet.2008.04.006 ↗
28. Tensile and creep-rupture response of additively manufactured nickel-based superalloy CM247LC10.1016/j.addlet.2022.100119 ↗
29. Combining alloy and process modification for micro-crack mitigation in an additively manufactured Ni-base superalloy
30. Microstructure and mechanical behavior of Inconel 625 alloy processed by selective laser melting at high temperature up to 1000 C10.1007/s12598-019-01321-3 ↗
31. Cao, Y., Bai, P., Liu, F., and Hou, X. (2019). Investigation on the precipitates of IN718 alloy fabricated by selective laser melting. Metals, 9.10.3390/met9101128 ↗
32. Evolution of precipitated phase in GH625 alloy during long term aging
33. Thermodynamic calculation of precipitated phases in alloy GH3625
34. Microstructural changes in alloy 625 during high temperature creep10.1016/j.matchar.2007.03.007 ↗
35. Nucleation and coarsening mechanism of δ phase in Inconel 625 deposited metal
36. Xu, J., Gruber, H., Peng, R.L., and Moverare, J. (2020). A novel γ′-strengthened nickel-based superalloy for laser powder bed fusion. Materials, 13.10.3390/ma13214930 ↗
37. Misorientation-dependent solute enrichment at interfaces and its contribution to defect formation mechanisms during laser additive manufacturing of superalloys10.1103/PhysRevMaterials.3.123602 ↗
38. Microstructure-performance relationships in Ni-based superalloy with coprecipitation of γ′ and γ″ phases10.1016/j.msea.2022.143954 ↗
39. Alloys-by-design: Application to new superalloys for additive manufacturing10.1016/j.actamat.2020.09.023 ↗
40. Research progress in evolution of precipitated phases in Inconel 625 superalloy
41. Sigma phase embrittlement-induced failures of heat-resistant stainless steel traveling grate links10.1016/j.engfailanal.2022.106979 ↗
42. Effect of δ phase on high temperature mechanical performances of Inconel 718 fabricated with SLM process10.1016/j.msea.2019.138327 ↗
43. Influence of heat treatments on microstructure evolution and mechanical properties of Inconel 625 processed by laser powder bed fusion10.1016/j.msea.2018.05.044 ↗
44. Influence of heat treatments on the microstructure and mechanical properties of Inconel 625 fabricated by directed energy deposition10.1016/j.msea.2021.141309 ↗