journal article·2023-06-02Open access

Effect of Laser Remelting of Fe-Based Thermally Sprayed Coating on AZ91 Magnesium Alloy on Its Structural and Tribological Properties

Martin Buchtík, Matěj Březina, Libor Mrňa, Marek Palán, Jan Filipenský, Pavel Doležal, David Nečas, Josef Frýza, Daniel Kajánek, Jaromír Wasserbauer, Leoš Doskočil

Coatings· Volume 13· Issue 6

Abstract

An Fe-based coating was thermally sprayed onto the surface of AZ91 magnesium alloy via the High-Velocity-Oxygen-Fuel (HVOF) method. The thermally sprayed coating with a thickness of 530 ± 25 µm and a porosity of 0.7 ± 0.1% did not show any macrostructural defects and did not cause any degradation of the AZ91 alloy. Laser remelting of the surface layer of the sprayed coating resulted in the recrystallization of the structure and the disappearance of presented pores, splat boundaries, and other defects. This led to an increase in the hardness of the remelted layer from the original 535 ± 20 HV0.3 up to 625 ± 5 HV0.3. However, during the laser remelting at a laser power of 1000 W, stress cracking in the coating occurred. The tribological properties were evaluated by the ball-on-plate method under dry conditions. Compared to the uncoated AZ91 magnesium alloy, a higher value of friction coefficient (COF) was measured for the as-sprayed coating. However, there was a decrease in wear rate and weight loss. The remelting of the surface layer of the as-sprayed coating led to a further decrease in the wear rate and weight loss. Based on the obtained data, it has been shown that the application of laser-remelted thermally sprayed Fe-based coatings on AZ91 Mg alloy improves hardness and tribological properties compared to bare Mg alloy and as-sprayed Fe-based coatings.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Magnesium Alloys: Properties and Applications · Aluminum Alloys Composites Properties · High-Temperature Coating Behaviors

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Materials Research Centre, Faculty of Chemistry, Brno University of Technology, Purkynova 464/118, 612 00 Brno, Czech Republic

Institute of Scientific Instruments of the Czech Academy of Sciences, Kralovopolska, 147, 612 64 Brno, Czech Republic

Faculty of Mechanical Engineering, Brno University of Technology, Technicka 2896/2, 602 00 Brno, Czech Republic

Department of Materials and Engineering Metallurgy, Faculty of Mechanical Engineering, University of West Bohemia, Univerzitni 22, 301 00 Plzen, Czech Republic

PLASMAMETAL, Ltd., Tovarni 917/1e, 643 00 Brno, Czech Republic

Research Centre, University of Zilina, Univerzitna 8215/1, 010 26 Zilina, Slovakia

Funding

Ministry of Education, Youth and Sports of the Czech Republic · Science Grant Agency of the Slovak Republic

References (64)

Show source-provided references
1. Friedrich, H.E., and Mordike, B.L. (2006). Magnesium Technology: Metallurgy, Design Data, Applications, Springer.
2. Discontinuous and continuous precipitation in magnesium–aluminium type alloys10.1016/j.jallcom.2008.11.008 ↗
3. Investigation of HVOF spraying on magnesium alloys10.1016/j.surfcoat.2006.06.047 ↗
4. Magnesium and its alloys applications in automotive industry10.1007/s00170-007-1279-2 ↗
5. Magnesium: Properties—Applications—Potential10.1016/S0921-5093(00)01351-4 ↗
6. Effect of Zn content on the chemical conversion treatments of AZ91D magnesium alloy10.1016/j.apsusc.2012.07.130 ↗
7. Pekguleryuz, M. (2006). Magnesium casting alloys. Magn. Technol. Metall. Des. Data Appl., 145–218.
8. Corrosion and Protection of Magnesium Alloys: An Overview of Research Undertaken by CAST10.4028/www.scientific.net/MSF.488-489.649 ↗
9. Song, G.-L. (2013). Corrosion Prevention of Magnesium Alloys, Woodhead Publishing.10.1533/9780857098962 ↗
10. Song, G.-L. (2011). Corrosion of Magnesium Alloys, Woodhead Publishing.10.1533/9780857091413 ↗
11. Influence of Homogenization Annealing of AZ91 on Mechanical Properties and Corrosion Behavior10.1002/adem.200700234 ↗
12. Iwaszko, J., and Strzelecka, M. (2022). Microstructure and Corrosion Resistance of AZ91 Magnesium Alloy after Surface Remelting Treatment. Materials, 15.10.3390/ma15248980 ↗
13. Hadzima, B., Kajánek, D., Jambor, M., Drábiková, J., Březina, M., Buhagiar, J., Pastorková, J., and Jacková, M. (2020). PEO of AZ31 Mg Alloy: Effect of Electrolyte Phosphate Content and Current Density. Metals, 10.10.3390/met10111521 ↗
14. Corrosion Inhibitors Intercalated into Layered Double Hydroxides Prepared In Situ on AZ91 Magnesium Alloys: Structure and Protection Ability10.1021/acsami.2c18675 ↗
15. Doskočil, L., Šomanová, P., Másilko, J., Buchtík, M., Hasoňová, M., Kalina, L., and Wasserbauer, J. (2022). Characterization of Prepared Superhydrophobic Surfaces on AZ31 and AZ91 Alloys Etched with ZnCl2 and SnCl2. Coatings, 12.10.3390/coatings12101414 ↗
16. Buchtík, M., Kosár, P., Wasserbauer, J., Tkacz, J., and Doležal, P. (2018). Characterization of Electroless Ni–P Coating Prepared on a Wrought ZE10 Magnesium Alloy. Coatings, 8.10.3390/coatings8030096 ↗
17. Buchtík, M., Krystỳnová, M., Másilko, J., and Wasserbauer, J. (2019). The Effect of Heat Treatment on Properties of Ni–P Coatings Deposited on a AZ91 Magnesium Alloy. Coatings, 9.10.3390/coatings9070461 ↗
18. Wasserbauer, J., Buchtík, M., and Brescher, R. (2019, January 22–24). Investigation of Ni-P coatings on AZ91 cast magnesium alloy. Proceedings of the 28th International Conference on Metallurgy and Materials, Brno, Czech Republic.10.37904/metal.2019.891 ↗
19. Influence of laser remelting on the microstructure and corrosion behavior of HVOF-sprayed Fe-based coatings on magnesium alloy10.1016/j.matchar.2022.112343 ↗
20. Microstructure and Sliding Wear Behavior of Fe-Based Coatings Manufactured with HVOF and HVAF Thermal Spray Processes10.1007/s11666-016-0410-z ↗
21. Tribology of HVOF- and HVAF-sprayed WC–10Co4Cr hardmetal coatings: A comparative assessment10.1016/j.surfcoat.2015.01.048 ↗
22. Fauchais, P.L., Heberlein, J.V.R., and Boulos, M.I. (2014). Thermal Spray Fundamentals: From Powder to Part, Springer Science & Business Media.10.1007/978-0-387-68991-3 ↗
23. Sobolev, V.V., Guilemany, J.M., Nutting, J., and Joshi, S. (2004). High Velocity Oxy-Fuel Spraying: Theory, Structure-Property Relationships and Applications, Maney.
24. Effect of severe shot peening on corrosion behavior of AZ31 and AZ91 magnesium alloys10.1016/j.jallcom.2018.08.141 ↗
25. Effects of nanofeatures induced by severe shot peening (SSP) on mechanical, corrosion and cytocompatibility properties of magnesium alloy AZ3110.1016/j.actbio.2017.11.032 ↗
26. Wagner, L. (2003). Shot Peening, Wiley-VCH Verlag GmbH & Co. KGaA.
27. Effect of laser shock peening on tribological properties of magnesium alloy ZK6010.1016/j.triboint.2019.106138 ↗
28. Oxidation resistant FeCoNiCrAl high entropy alloy/AlSi12 composite coatings with excellent adhesion on Ti-6Al-4 V alloy substrate via mechanical alloying and subsequent laser cladding10.1016/j.surfcoat.2023.129577 ↗
29. The role of pin eccentricity in friction stir welding of Al-Mg-Si alloy sheets: Microstructural evolution and mechanical properties10.1007/s00170-022-09793-x ↗
30. Effect of neodymium on microstructure and corrosion resistance of AZ91 magnesium alloy10.1007/s10853-006-0661-z ↗
31. Effect of Neodymium on Microstructure and Mechanical Properties of Mg-Sb Alloy10.1016/S1002-0721(07)60405-0 ↗
32. Effect of minor Sc on the microstructure and mechanical properties of AZ91 Magnesium Alloy10.1016/j.pnsc.2018.01.006 ↗
33. Microstructure and mechanical properties of AZ91 magnesium alloy with minor additions of Sm, Si and Ca elements10.1007/s41230-019-9067-9 ↗
34. Microstructural evolution of the interface between NiCrAlY coating and superalloy during isothermal oxidation10.1016/j.matdes.2015.05.014 ↗
35. Cold spray Al-5% Mg coatings for the corrosion protection of magnesium alloys10.1007/s11666-011-9675-4 ↗
36. Improved corrosion resistance of AZ91D magnesium alloy coated by novel cold-sprayed Zn-HA/Zn double-layer coatings10.1016/j.ceramint.2019.11.271 ↗
37. Mechanical properties of thermally sprayed Fe based coatings10.1179/1743284710Y.0000000002 ↗
38. Fe-based amorphous coating for corrosion protection of magnesium alloy10.1016/j.matdes.2016.07.031 ↗
39. Wear Resistance of Stainless Steel Coatings on ZE41 Magnesium Alloy10.1007/s11666-018-0779-y ↗
40. Microstructure and wear behavior of Fe-based amorphous HVOF coatings produced from commercial precursors10.1016/j.surfcoat.2016.10.057 ↗
41. 3.13 Finishing and Post-Treatment of Thermal Spray Coatings10.1016/B978-0-12-803581-8.09200-6 ↗
42. Effect of cooling rate on residual stress and mechanical properties of laser remelted ceramic coating10.1016/j.jeurceramsoc.2018.04.020 ↗
43. Effect of heat treatment on the microstructure and mechanical properties of Fe-based amorphous coatings10.1016/j.jallcom.2009.02.107 ↗
44. Formation of eutectic carbides in Fe–Cr–Mo–C alloy during non-equilibrium crystallization10.1016/j.matdes.2016.01.028 ↗
45. The effect of temperature on the evolution of eutectic carbides and M7C3→M23C6 carbides reaction in the rapidly solidified Fe-Cr-C alloy10.1016/j.jallcom.2016.12.252 ↗
46. Corrosion and wear properties of FeCrMnCoSi HVOF coatings10.1016/j.surfcoat.2018.10.101 ↗
47. Metallic glasses as structural materials10.1016/j.scriptamat.2005.09.051 ↗
48. Samal, S., Tyc, O., Cizek, J., Klecka, J., Lukáč, F., Molnárová, O., de Prado, E., Weiss, Z., Kopeček, J., and Heller, L. (2021). Fabrication of thermal plasma sprayed niti coatings possessing functional properties. Coatings, 11.10.3390/coatings11050610 ↗
49. Effect of iron oxide debris on the reciprocating sliding wear of tool steels
50. The characterization of wear transitions in sliding wear process contaminated with silica and iron powder10.1016/j.triboint.2004.06.007 ↗
51. Effect of wear debris on wear in rolling-sliding motion10.1016/0043-1648(83)90183-7 ↗
52. Enhanced mechanical properties of Mg–Al–Zn cast alloy via friction stir processing10.1016/j.scriptamat.2006.10.035 ↗
53. Chen, Q., Zhao, Z., Zhu, Q., Wang, G., and Tao, K. (2018). Cerium addition improved the dry slidingwear resistance of surface welding AZ91 alloy. Materials, 11.10.3390/ma11020250 ↗
54. Fracture behavior of AZ91 magnesium alloy10.1016/S0167-577X(00)00041-0 ↗
55. Effects of heat treatment on the wear behavior of surfacing AZ91 magnesium alloy10.1557/jmr.2017.186 ↗
56. Effect of Surface Mechanical Attrition Treatment on Tribological Behavior of the AZ31 Alloy10.1016/j.jmst.2016.05.018 ↗
57. An investigation on the tribological behavior of AZ91 and AZ91+3wt% RE magnesium alloys at elevated temperatures10.1016/j.matdes.2013.08.073 ↗
58. Spherical shape of γ-Mg17Al12 precipitates in AZ91 magnesium alloy processed by equal-channel angular pressing10.1016/j.jallcom.2009.07.100 ↗
59. Myshkin, N.K., and Grigoriev, A.Y. (2015). 2015 IFToMM World Congress Proceedings, IFToMM 2015, National Taiwan University.
60. Rivera-Tello, C.D., Broitman, E., Flores-Ruiz, F.J., Perez-Alvarez, J., Flores-Jiménez, M., Jiménez, O., and Flores, M. (2020). Micro and macro-tribology behavior of a hierarchical architecture of a multilayer tan/ta hard coating. Coatings, 10.10.3390/coatings10030263 ↗
61. Microstructure of spray formed 2.9%C-22%Cr high chromium white cast iron10.4028/www.scientific.net/MSF.416-418.419 ↗
62. Microstructure-property relationships in high chromium white iron alloys10.1179/imr.1996.41.2.59 ↗
63. Wang, K., Chang, B., Lei, Y., Fu, H., and Lin, Y. (2017). Effect of cobalt on microstructure and wear resistance of Ni-based alloy coating fabricated by laser cladding. Metals, 7.10.3390/met7120551 ↗
64. Corrosion and corrosion-friction properties of plasma cladding wear-resistant layer on Fe-based alloy10.1088/2053-1591/aaae7f ↗