journal article·2023-06-12Open access

Influence of Remaining Oxide on the Adhesion Strength of Supersonic Particle Deposition TiO2 Coatings on Annealed Stainless Steel

Noor Omar, Yusliza Yusuf, Syahrul Sundi, Ilyani Abu Bakar, Verry Andre Fabiani, Toibah Abdul Rahim, Motohiro Yamada

Coatings· Volume 13· Issue 6

Abstract

The cold spray or Supersonic Particle Deposition technique has great potential for producing ceramic nanostructured coatings. This technique operates at a processing temperature that is low enough to preserve the initial feedstock materials’ microstructure. Nevertheless, depositing ceramic powders using a cold spray can be challenging because of the materials’ brittle nature. The interaction between substrate and particles is significantly influenced by substrate attributes, including hardness, material nature, degree of oxidation and temperature. In this study, the effect of the substrate’s remaining oxide composition on the adhesion strength of an agglomerated nano-TiO2 coating was investigated. The results showed that the coating adhesion strength increased for hard materials such as stainless steel and pure chromium as the annealed substrate temperature also increased from room temperature to 700 °C, indicating thicker oxide on the substrate surface. TiO2 particles mainly bond with SUS304 substrates through oxide bonding, which results from a chemical reaction involving TiO2-OH−. Chromium oxide (Cr2O3) is thermodynamically preferred in SUS304 and provides the OH− component required for the reaction. SUS304 shows a thermodynamic preference for chromium oxide (Cr2O3), and this enables Cr2O3 to provide the necessary OH− component for the reaction.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced ceramic materials synthesis · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Faculty of Mechanical Engineering and Manufacturing Technology, Universiti Teknikal Malaysia Melaka, Durian Tunggal, Melaka 76100, Malaysia

School of Civil Engineering, College of Engineering, Universiti Teknologi MARA, Shah Alam 40450, Malaysia

Department of Chemistry, Faculty of Engineering, Universitas Bangka Belitung, Pangkalpinang 33172, Indonesia

Faculty of Manufacturing Engineering, Universiti Teknikal Malaysia Melaka, Durian Tunggal, Melaka 76100, Malaysia

Department of Mechanical Engineering, Toyohashi University of Technology, 1-1 Tempaku-Cho, Toyohashi 441-8580, Japan

Funding

JSPS KAKENHI

References (38)

Show source-provided references
1. Erratum to: From Particle acceleration to impact and bonding in cold spraying10.1007/s11666-009-9399-x ↗
2. Influence of impact conditions on feedstock deposition behavior of cold-sprayed Fe-based metallic glass10.1007/s11666-018-0720-4 ↗
3. Single impact bonding of cold sprayed Ti-6Al-4V powders on different substrates10.1007/s11666-014-0200-4 ↗
4. Nature of the interfaces between the constituent phases in the high entropy alloy CoCrCuFeNiAl10.1016/j.ultramic.2013.06.006 ↗
5. Cold spraying—A materials perspective10.1016/j.actamat.2016.06.034 ↗
6. Bonding mechanism in cold gas spraying10.1016/S1359-6454(03)00274-X ↗
7. Effect of substrate surface roughness on properties of cold-sprayed copper coatings on SS316L steel10.1016/j.surfcoat.2020.125619 ↗
8. Influence of substrate roughness on bonding mechanism in cold spray10.1016/j.surfcoat.2016.07.082 ↗
9. Alkhimov, A.P., Papyrin, A.N., Vyazemskogo, U., Kosarev, V.F., Nesterovich, N.I., and Shushpanov, M.M. (1994). Gas-Dynamic Spraying Method for Applying a Coating. (U.S. Patent No 5,302,414).
10. Review on Cold Spray Process and Technology: Part I—Intellectual Property10.1007/s11666-008-9203-3 ↗
11. Goldbaum, D., Poirier, D., Irissou, E., Legoux, J.-G., and Moreau, C. (2015). Modern Cold Spray, Springer.
12. Cold spray coating: Review of material systems and future perspectives10.1179/1743294414Y.0000000270 ↗
13. Cold spraying of titanium: A review of bonding mechanisms, microstructure and properties10.4028/www.scientific.net/KEM.533.53 ↗
14. Deformation microstructure of cold gas sprayed coatings
15. Asymmetrical bonding in cold spraying of dissimilar materials10.1016/j.apsusc.2018.03.103 ↗
16. Adiabatic shear instability is not necessary for adhesion in cold spray10.1016/j.actamat.2018.07.065 ↗
17. Analysis of the impact velocity of powder particles in the cold-gas dynamic spray process10.1016/j.msea.2003.10.312 ↗
18. Comment on “Adiabatic shear instability is not necessary for adhesion in cold spray”10.1016/j.scriptamat.2018.10.036 ↗
19. Response to comment on “Adiabatic shear instability is not necessary for adhesion in cold spray”10.1016/j.scriptamat.2018.12.015 ↗
20. Development of thick copper claddings on SS316L steel for in-vessel components of fusion reactors and copper-cast iron canisters10.1016/j.fusengdes.2018.01.076 ↗
21. Splat formation and adhesion mechanisms of cold gas-sprayed Al coatings on Al2O3 substrates10.1007/s11666-013-9966-z ↗
22. Local heteroepitaxy as an adhesion mechanism in aluminium coatings cold gas sprayed on AlN substrates10.1016/j.actamat.2017.02.021 ↗
23. Evolution of microstructure of cold-spray aluminum coatings on Al2O3 substrates10.1002/adem.201100261 ↗
24. Marple, G.M.B.R., Agarwal, A., Hyland, M.M., Lau, Y.-C., Li, C.-J., and Lima, R.S. (2010, January 3–5). Deposition of TiO2 Ceramic Particles on Cold Spray Process. Proceedings of the International Thermal Spray Conference & Exposition Raffles City Convention Centre, Singapore.
25. Moulder, J.F., Stickle, W.F., Sobol, P.E., Bomben, K.D., and Chastain, J. (1993). Handbook of X-ray Photoelectron Spectroscopy, Perkin-Elmer Corporation Physical Electronics Division.
26. The interfacial restructuring to amorphous: A new adhesion mechanism of cold-sprayed coatings10.1016/j.matlet.2016.03.132 ↗
27. Advanced analysis of copper X-ray photoelectron spectra10.1002/sia.6239 ↗
28. A preliminary study of the ductility of chromium10.1149/1.2781099 ↗
29. Reaction layer at the interface between aluminium particles and a glass substrate formed by cold spray10.1088/0022-3727/46/19/195301 ↗
30. The influence of the substrate on the deposition of cold-sprayed titanium: An experimental and numerical study10.1007/s11666-010-9608-7 ↗
31. Influence of thermal properties and temperature of substrate on the quality of cold-sprayed deposits10.1016/j.actamat.2017.01.040 ↗
32. The effect of post-treatments on the powder morphology of titanium dioxide (TiO2) powders synthesized for cold spray10.1016/j.surfcoat.2011.07.030 ↗
33. Effect of substrate surface oxide film thickness on deposition behavior and deposition efficiency in the cold spray process10.1007/s11666-015-0299-y ↗
34. Effect of substrate temperature on deposition behavior of copper particles on substrate surfaces in the cold spray process10.1007/s11666-007-9121-9 ↗
35. On the role of substrate temperature into bonding mechanism of cold sprayed titanium dioxide
36. A Perspective review on the bonding mechanisms in cold gas dynamic spray10.1080/02670844.2018.1551768 ↗
37. Substrate pre-treatment by dry-ice blasting and cold spraying of titanium10.1080/02670844.2016.1210894 ↗
38. A Preliminary study into the effect of oxide chemistry on the bonding mechanism of cold-sprayed titanium dioxide coatings on SUS316 stainless steel substrate