journal article·2026-02-01Open access

Fluid–Structure Interaction Study of S-CO2 Radial Hydrodynamic Lubricated Bearings Under Different Rotational Speeds

Chengtao Niu, Sung-Ki Lyu, Yu-Ting Wu, Zhen Qin, Shixuan Wang, Sicheng Niu

Coatings· Volume 16· Issue 2

Abstract

High-speed rotating machinery often demands bearings with superior load capacity and thermal stability. Here, a four-chamber radial hydrodynamic sliding bearing using supercritical carbon dioxide (S-CO2) as a lubricant is investigated to address these requirements. The work is carried out on the ANSYS Workbench 2024 R1 platform. Computational fluid dynamics (CFD) and structural mechanics are combined to build a fluid–structure interaction (FSI) numerical model. The model accounts for real-gas thermophysical property variations. S-CO2 properties are dynamically retrieved using the REFPROP database and MATLAB curve fitting. Unlike previous studies that mainly focused on hydrostatic structures and general parameters, this research examines hydrodynamic lubrication behavior under ultra-high-speed conditions. It systematically analyzes the effects of rotational speed on oil film pressure distribution, load capacity, friction coefficient, and housing deformation. It also investigates cavitation characteristics in a specific speed range. Simulation outcomes reveal that higher rotational speeds lead to an increase in both oil film load capacity and peak pressure. In particular, when the speed rises from 4000 r/min to 12,000 r/min, the maximum positive pressure increases from about 10 MPa to approximately 10.4 MPa. Meanwhile, the negative pressure region becomes significantly larger, which raises the cavitation risk and indicates a less stable lubrication state at very high speeds. These results confirm that lubrication simulations incorporating real-gas effects can reliably represent the operating behavior and provide useful guidance. It also provides new theoretical support for the design optimization and engineering application of S-CO2-lubricated bearings in high-speed machinery.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Tribology and Lubrication Engineering · Gear and Bearing Dynamics Analysis · Adhesion, Friction, and Surface Interactions

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

School of Mechanical Engineering, Nantong Institute of Technology, Zibo 255049, China

School of Mechanical Engineering, Shandong University of Technology, Zibo 255049, China

School of Mechanical and Aerospace Engineering, Gyeongsang National University, Jinju-si 52828, Republic of Korea

School of Transportation and Vehicle Engineering, Shandong University of Technology, Zibo 255049, China

Zhejiang Shuanghuan Driveline Co., Ltd., Hangzhou 310023, China

Funding

Shandong Provincial Natural Science Foundation · NRF-NSFC Bilateral Collaboration Program · Material and Components Technology R&D Project of the Korea Ministry of Trade, Industry and Energy

References (25)

Show source-provided references
1. Liang, X., Han, M., He, T., Cui, L., Yang, Z., and Ouyang, W. (2023). A Mixed Lubrication Deterministic Model of an Elastic Support Water-Lubricated Tilting Pad Thrust Bearing. Lubricants, 11.10.3390/lubricants11060262 ↗
2. Kocman, F., and Novotný, P. (2025). On the Effectiveness of Optimisation Algorithms for Hydrodynamic Lubrication Problems. Lubricants, 13.10.3390/lubricants13050207 ↗
3. Marinković, A., Stojanović, B., Gachot, C., and Lazović, T. (2024). Analysis of Lubrication Regimes for Porous Sliding Bearing. Lubricants, 12.10.3390/lubricants12060184 ↗
4. Elasto-hydrodynamic lubrication of the journal bearing system with a relief groove in the scroll compressor: Simulation and experiment10.1016/j.triboint.2021.107252 ↗
5. The Spatial Elastic-Hydrodynamic Problem of Lubrication of Radial Sliding Bearings10.1134/S1052618824701577 ↗
6. Chen, Y., Zhao, Z., Zhang, H., Li, X., and Shi, Z. (2025). Analytical and Experimental Investigation of Nonlinear Dynamic Characteristics of Hydrodynamic Bearings for Oil Film Instability Detection. Machines, 13.10.3390/machines13060444 ↗
7. Wettmarshausen, S., Engels, A., Hagemann, T., Stottrop, M., Weißbacher, C., Schwarze, H., and Bender, B. (2025). An Experimentally Validated Cavitation Model for Hydrodynamic Bearings Using Non-Condensable Gas. Lubricants, 13.10.3390/lubricants13040140 ↗
8. Stefani, F.A., Niccolini Marmont Du Haut Champ, C.A., Silvestri, P., and Massardo, A.F. (2024). Experimental and Numerical Analysis of Torsional—Lateral Vibrations in Drive Lines Supported by Hydrodynamic Journal Bearings. Lubricants, 12.10.3390/lubricants12030082 ↗
9. Investigation on the influence of rotational speed on oil film stability of hydrostatic rotary table10.1108/ILT-07-2024-0267 ↗
10. A novel design of journal bearings for stability under shock loads10.1038/s41598-024-73178-1 ↗
11. Effect of Operating Condition and Structural Parameter in the Hydrostatic Thrust CO2 Bearing10.1007/s11630-019-1113-9 ↗
12. Thermohydrodynamic investigation for supercritical carbon dioxide high speed tilting pad bearings considering turbulence and real gas effect10.1063/5.0065343 ↗
13. Mehdi, S.M., and Kim, T.H. (2022). Computational Model Development for Hybrid Tilting Pad Journal Bearings Lubricated with Supercritical Carbon Dioxide. Appl. Sci., 12.10.3390/app12031320 ↗
14. Operating characteristics of supercritical carbon dioxide high speed tilting pad bearings considering inertia effect10.1177/16878132231170785 ↗
15. Structural stiffness and equivalent viscous damping in a supercritical carbon dioxide lubricated hybrid journal bearing under hydrostatic status10.1108/ILT-07-2023-0213 ↗
16. Han, D., and Bi, C. (2022). The Partial Derivative Method for Dynamic Stiffness and Damping Coefficients of Supercritical CO2 Foil Bearings. Lubricants, 10.10.3390/lubricants10110307 ↗
17. The influence and a direct judgement method of the flow state in supercritical CO2 dry gas seal10.1007/s40430-021-03211-1 ↗
18. Experimental study on forced convective heat transfer of supercritical carbon dioxide in a horizontal circular tube under high heat flux and low mass flux conditions10.1177/1687814019830804 ↗
19. Study on a high-speed oil-free pump with fluid hydrodynamic lubrication10.1177/1687814020945463 ↗
20. Numerical Modeling and Experimental Validation of a Supercritical CO2-Lubricated Hydrodynamic Journal Bearing10.1115/1.4049724 ↗
21. Patel, A., and Kumar, P. (2023). Numerical Investigations of Sector-Shaped Hybrid Fluid Film Thrust Bearing for High-Speed sCO2 Turbomachinery. Proceedings of the ASME Turbo Expo 2023: Turbomachinery Technical Conference and Exposition, Boston, MA, USA, 26–30 June 2023, ASME.10.1115/GT2023-103582 ↗
22. Patel, A., K. Balasubramanian, A., Biradar, V., Srivatsa, S., Kumar, P., and Sonti, V.R. (2023). Analysis of Aerostatic Thrust Bearing for S-CO2 Turbomachinery. Proceedings of the ASME 2019 Gas Turbine India Conference, Chennai, India, 5–6 December 2019, ASME.10.1115/GTINDIA2019-2643 ↗
23. Niu, C., Lyu, S.-K., Wu, Y.-T., Qin, Z., and Zhang, J. (2025). Fluid Characteristics of Radial Hydrodynamic Bearings Using Supercritical Carbon Dioxide as Lubricant. Lubricants, 13.10.3390/lubricants13060271 ↗
24. Validation of a system code (GAMMA+) using standard k-ε model for multi-dimensional turbulent flows in various geometries10.1016/j.nucengdes.2025.114079 ↗
25. Analysis of Turbulence and Convective Inertia in a Water-Lubricated Tilting-Pad Journal Bearing Using Conventional and CFD Approaches10.1080/10402004.2016.1251668 ↗