Nondestructive Assessment of Quality Characteristics of As-Built Additive Manufacturing Aeronautical AlSi10Mg and Inspection of Offset
Source abstract
Abstract
AlSi10Mg is widely used in additively manufacturing aeronautical lattice and honeycomb structures. The unclear complex quality characteristics has been an obstacle of nondestructive testing of additive manufacturing (AM) AlSi10Mg, especially at its as-built state. This article attempts to reveal the quality characteristics of as-built AM aeronautical AlSi10Mg based on its conductivity characteristics. Experimental results show that the quality of manufacturing is nonuniform. The nonuniformity of each sample surface is systematically evaluated. Along the building direction, the quality is best in the initial few layers and decreases as the built height increases. On this basis, a reference curve is obtained and used to describe the quality characteristics of as-built AM component along the building direction. Based on the quality characteristics, the inspection of small offsets caused by accidental failures during the manufacturing process is carried out. The offsets not <37 μm are detected with the help of the reference curve, whereas they are not discovered by the radiography testing. It proves that the proposed method of offset inspection is highly sensitive.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing Materials and Processes · Welding Techniques and Residual Stresses · Industrial Vision Systems and Defect Detection
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
School of Aerospace Engineering, Xiamen University, Xiamen, China.
References (47)
Show source-provided references
1. 10.1038/s41586-018-0850-310.1038/s41586-018-0850-3 ↗
2. 10.1016/j.scriptamat.2017.07.02010.1016/j.scriptamat.2017.07.020 ↗
3. 10.1002/adem.20170084210.1002/adem.201700842 ↗
4. 10.1016/j.phpro.2012.10.05910.1016/j.phpro.2012.10.059 ↗
5. 10.1016/j.jallcom.2018.12.26710.1016/j.jallcom.2018.12.267 ↗
6. 10.1063/1.491459410.1063/1.4914594 ↗
7. 10.1016/j.msea.2016.06.01310.1016/j.msea.2016.06.013 ↗
8. 10.1016/j.matdes.2020.10870910.1016/j.matdes.2020.108709 ↗
9. 10.1016/j.matdes.2020.10936010.1016/j.matdes.2020.109360 ↗
10. 10.1016/j.tws.2021.10779510.1016/j.tws.2021.107795 ↗
11. 10.1109/JSEN.2018.285265710.1109/JSEN.2018.2852657 ↗
12. 10.1016/j.ndteint.2018.12.00110.1016/j.ndteint.2018.12.001 ↗
13. 10.1016/j.addma.2018.03.02010.1016/j.addma.2018.03.020 ↗
14. Todorov E. Measurement of electromagnetic properties of powder and solid metal materials for additive manufacturing. Proc SPIE, 2017; 10169:101690701–101690711; doi: 10.1117/12.2261393
15. 10.1002/adem.20160007810.1002/adem.201600078 ↗
16. 10.1007/s40194-018-0593-710.1007/s40194-018-0593-7 ↗
17. Boillat E Fivat D Jhabvala J et al. A Review of Different Techniques to Characterize the Mechanical Properties of SLS Parts-Focus on Resistivity Measurements Innovative Developments in Virtual and Physical Prototyping. CRC Press: Leiden; 2012; doi: 10.1201/b11341–b1134510.1201/b11341-45 ↗
18. Kemerling B, , Ryan D. Development of production eddy current inspection process for additively manufactured industrial gas turbine engine components. Proc Turbomach Tech Conf Expo, 2019; 5:1–8; doi: 10.1115/GT2019-90971
19. 10.1080/10426914.2020.178493710.1080/10426914.2020.1784937 ↗
20. 10.1007/s11837-015-1810-010.1007/s11837-015-1810-0 ↗
21. 10.1007/s10853-017-1371-410.1007/s10853-017-1371-4 ↗
22. Koester L, , Bond L, , Taheri H, et al. Nondestructive evaluation of additively manufactured metallic parts: In situ and post desposition. In: Additive Manufacturing for The Aerospace Industry. Elsevier: Amsterdam;, 2019; pp. 401–417; doi: 10.1016/B978-0-12-814062-8.00020-0
23. Gite R, , Wakchaure V. A review on process parameters, microstructure and mechanical properties of additively manufactured AlSi10Mg alloy. Mater Today Proc, 2022; doi: 10.1016/j.matpr.2022.09.100
24. Ghio E, , Cerri E. Work hardening of heat-treated AlSi10Mg alloy manufactured by single and double laser selective laser melting: Effects of layer thickness and hatch spacing. Materials, 2021; 14(4901):1–22; doi: 10.3390/ma14174901
25. 10.1016/j.ijfatigue.2020.10573710.1016/j.ijfatigue.2020.105737 ↗
26. 10.1007/s11665-014-0958-z10.1007/s11665-014-0958-z ↗
27. 10.1016/j.actamat.2010.02.00410.1016/j.actamat.2010.02.004 ↗
28. Sharratt B. Nondestructive Techniques and Technologies for Qualification of Additive Manufactured Components and Processes: A Literature Review. Sharratt Research and Consulting Inc.: Victoria; 2015.
29. Waller J, , Parker B, , Hodges K, et al. Qualification of products fabricated via additive manufacturing using nondestructive evaluation. Safety Mission Assurance Conf, 2015; 1–44.
30. 10.1016/J.ENG.2017.05.01710.1016/J.ENG.2017.05.017 ↗
31. Li J, , Hu J, , Zhu Y, et al. Surface roughness control of root analogue dental implants fabricated using selective laser melting. Addit Manuf, 2020; 34:101283; doi: 10.1016/j.addma.2020.101283
32. Campbell R, , Martorelli M, , Lee H. Surface roughness visualisation for rapid prototyping models. Comput Des, 2002; 34:717–725; doi: 10.1016/S0010-4485(01)00201-9
33. Ghanekar A Crawford R Watson D. Optimization of SLS process parameters using D-optimality. University of Texas at Austin: Austin; 2003.
34. Thiel C, , Stubenvoll M, , Schäfer B. Reliable beam positioning for metal-based additive manufacturing by means of focal shift reduction. Lasers Manuf Conf, 2015; 1–8.
35. Goossens L, , Kruth J, , Hooreweder B. On the influence of thermal lensing during selective laser melting. Solid Free Fabr, 2018; 2267–2274.
36. Gong L, , Rafi K, , Gu H, et al. Analysis of defect generation in Ti–6Al–4V parts made using powder bed fusion additive manufacturing processes. Addit Manuf, 2014; 1–4:87–98.
37. Gong H, , Nadimpalli V, , Rafi K, et al. Micro-CT evaluation of defects in Ti-6Al-4V parts fabricated by metal additive manufacturing. Tech, 2019; 7–44:1–12; doi: 10.1016/j.addma.2014.08.002
38. 10.1016/j.matdes.2018.04.01910.1016/j.matdes.2018.04.019 ↗
39. Bean G, , Witkin D, , Mclouth T, et al. Effect of laser focus shift on surface quality and density of Inconel 718 parts produced via selective laser melting. Addit Manuf, 2018; 22:207–215; doi: 10.1016/j.addma.2018.04.024
40. Gong H. Generation and detection of defects in metallic parts fabricated by selective laser melting and electron beam melting and their effects on mechanical properties. Dissertation, University of Louisville: Louisville, US. 2013; pp. 1–218; doi: 10.1016/j.addma.2014.08.002
41. 10.1016/j.jmatprotec.2020.11694810.1016/j.jmatprotec.2020.116948 ↗
42. 10.1007/s00170-017-1354-210.1007/s00170-017-1354-2 ↗
43. Collaboration for NDT Education Conductivity and Resistivity Values for Aluminum & Alloys. Available from: https://wenku.baidu.com/view/cb4218345aeef8c75fbfc77da26925c52cc59118.html [Last accessed: January27 2023].
44. 10.1177/095440541243708510.1177/0954405412437085 ↗
45. 10.1080/17452759.2017.135731910.1080/17452759.2017.1357319 ↗
46. Justin S. Additive manufacturing (AM) activities & non-destructive evaluation (NDE) at GSFC, JAXA Delegation Visit, 2017; 1–38.
47. Qiang T. Radiography Testing. China Labor and Social Security Press: Beijing; 2008 (in Chinese).