Evaluation of the mechanical properties and degree of conversion of 3D printed splint material
Source abstract
Abstract
Objective To evaluate the effect of post-curing method, printing layer thickness, and water storage on the mechanical properties and degree of conversion of a light-curing methacrylate based resin material (IMPRIMO® LC Splint), used for the fabrication of 3D printed occlusal splints and surgical guides. Methods 96 bar-shaped specimens were 3D printed (Asiga MAX), half of them with a layer thickness of 100 μm (Group A), and half with 50 μm (Group B). Each group was divided in three subgroups based on the post-curing method used: post-curing with light emitting diode (LED) and nitrogen gas; post-curing with only LED; and non-post-curing. Half of the specimens from each subgroup were water-stored for 30 days while the other half was dry-stored (n = 8). Flexural strength and flexural modulus were evaluated. Additional specimens were prepared and divided in the same way for surface hardness (n = 96), fracture toughness, and work of fracture (n = 96). Five specimens were selected from each subgroup for evaluating the degree of conversion (DC). Data were collected and statistically analyzed with 1-way, 2-way ANOVA, and Tukey post-hoc analysis (α = 0.05). Results The 2-way ANOVA showed that the post-curing method and water storage significantly affected the investigated mechanical properties (P < 0.001). The 1-way ANOVA revealed a statistically significant difference among the tested groups on the investigated properties (P < 0.001). After water storage, the 100 μm subgroup post-cured with only LED showed higher flexural strength (51 ± 9) than the 50 μm and 100 μm subgroups that were post-cured with LED in addition to nitrogen gas atmosphere (38 ± 5, 30 ± 3) (p < 0.05). The 50 μm subgroup post-cured with only LED showed the highest significant flexural modulus values (1.7 ± 0.08) (p < 0.05). However, the 50 μm subgroup post-cured with LED plus nitrogen showed significantly higher surface hardness values (p < 0.05) among the investigated groups. The non-post-cured subgroups showed the lowest values, which were significantly different from the other subgroups (p < 0.05). Conclusion The post-curing method, water storage, and printing layer thickness play a role in the mechanical properties of the investigated 3D Printed occlusal splints material. The combination of heat and light within the post-curing unit can enhance the mechanical properties and degree of conversion of 3D printed occlusal splints. Flexural strength and surface hardness can increase when decreasing printing layer thickness.
Source: europepmc · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Dental materials and restorations · Surgical Sutures and Adhesives · Organ and Tissue Transplantation Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. Effect of preheating on the viscoelastic properties of dental composite under different deformation conditions10.4012/dmj.2015-042 ↗
2. CAD/CAM/AM applications in the manufacture of dental appliances10.1016/j.ajodo.2012.04.023 ↗
3. Effect of 3D printing direction and water storage on nano-mechanical properties of 3D printed and auto-polymerized polymer with special emphasis on printing layer interface10.1166/mex.2019.1502 ↗
4. Clinical comparison of conventional and additive manufactured stabilization splints10.1080/23337931.2018.1497491 ↗
5. Clinical comparison of conventional and additive manufactured stabilization splints10.1080/23337931.2018.1497491 ↗
6. Oxygen inhibition layer of composite resins: effects of layer thickness and surface layer treatment on the interlayer bond strength10.1111/eos.12167 ↗
7. Mechanical properties, fracture resistance, and fatigue limits of short fiber reinforced dental composite resin10.1016/j.prosdent.2015.07.012 ↗
8. Mechanical and structural characterization of discontinuous fiber-reinforced dental resin composite10.1016/j.jdent.2016.07.009 ↗
9. Degree of conversion and mechanical properties of a BisGMA:TEGDMA composite as a function of the applied radiant exposure10.1002/jbm.b.30897 ↗
10. Cure depth control for complex 3D microstructure fabrication in dynamic mask projection microstereolithography10.1108/13552540910925072 ↗
11. Effectiveness of light emitting diode and halogen light curing units for curing microhybrid and nanocomposites10.4103/0972-0707.111322 ↗
12. Oral splints: the crutches for temporomandibular disorders and bruxism?10.1177/10454411980090030701 ↗
13. Monomer conversion of pre-heated composite10.1177/154405910508400716 ↗
14. Digital Michigan splint - from intraoral scanning to plasterless manufacturing
15. Effect of temperature, curing time, and filler composition on surface microhardness of composite resins10.4103/0972-0707.153071 ↗
16. Correlation of the degree of conversion with the amount of elutable substances in nano-hybrid dental composites10.1016/j.dental.2012.08.006 ↗
17. Solvent degradation and reduced fracture toughness in aged composites10.1177/00220345920710010101 ↗
18. In vitro aging of dental composites in water—effect of degree of conversion, filler volume, and filler/matrix coupling10.1002/(SICI)1097-4636(19981205)42:3<465::AID-JBM17>3.0.CO;2-F ↗
19. Selective laser sintering (SLS) 3D printing of medicines10.1016/j.ijpharm.2017.06.082 ↗
20. Cytotoxic effects of dental bonding substances as a function of degree of conversion10.1016/j.dental.2008.07.003 ↗
21. Systematic review and meta-analysis of randomized controlled trials evaluating intraoral orthopedic appliances for temporomandibular disorders
22. 3D printing preview for stereo-lithography based on photopolymerization kinetic models
23. The potential of unsaturated polyesters in biomedicine and tissue engineering: synthesis, structure-properties relationships and additive manufacturing10.1016/j.progpolymsci.2016.12.008 ↗
24. Materials analysis of stereolithography resins for use in Rapid Manufacturing10.1023/B:JMSC.0000020010.73768.4a ↗
25. Microhardness evaluation of resin composites polymerized by three different light sources10.4012/dmj.26.845 ↗
26. Polishability and wear resistance of splint material for oral appliances produced with conventional, subtractive, and additive manufacturing10.1016/j.jmbbm.2017.07.019 ↗
27. Study of shrinkage strains in a stereolithography cured acrylic photopolymer resin10.1016/S0924-0136(03)00028-1 ↗
28. Oral appliances in the management of temporomandibular disorders10.1016/j.tripleo.2008.10.007 ↗
29. Influence of layer thickness on mechanical properties in stereolithography10.1108/13552540610652456 ↗
30. Hardness evaluation of a dental composite polymerized with experimental LED-based devices10.1016/S0109-5641(00)00088-9 ↗
31. Occlusal stabilization splint for patients with temporomandibular disorders: meta-analysis of short and long term effects10.1371/journal.pone.0171296 ↗
32. The influence of short-term water storage on the flexural properties of unidirectional glass fiber-reinforced composites10.1016/S0142-9612(01)00355-6 ↗
33. A new computer-assisted method for design and fabrication of occlusal splints10.1016/j.ajodo.2007.11.018 ↗
34. A new computer-assisted method for design and fabrication of occlusal splints10.1016/j.ajodo.2007.11.018 ↗
35. Patient preference for light-cured composite bite splint compared to heat-cured acrylic bite splint10.1902/jop.2001.72.8.1108 ↗
36. Hydrogen bonding interactions in methacrylate monomers and polymers10.1002/jbm.a.31448 ↗
37. Rapid prototyping in dentistry: technology and application10.1007/s00170-005-2523-2 ↗
38. Fracture resistance and 2-body wear of 3-dimensional–printed occlusal devices10.1016/j.prosdent.2018.04.007 ↗
39. Diametral tensile strength and Vickers hardness of a composite after storage in different solutions10.2334/josnusd.49.61 ↗
40. Quantitative study of bite force during sleep associated bruxism10.1046/j.1365-2842.2001.00692.x ↗
41. Influence of chain extender length of aromatic dimethacrylates on polymer network development10.1016/j.dental.2007.03.007 ↗
42. O'Neill · 2017
43. Current status of bioinks for micro-extrusion-based 3D bioprinting10.3390/molecules21060685 ↗
44. The difference in degree of conversion between light-cured and additional heat-cured composites
45. Assessment of CAD-CAM polymers for digitally fabricated complete dentures
46. 3D printing based on imaging data: review of medical applications10.1007/s11548-010-0476-x ↗
47. A digital process for additive manufacturing of occlusal splints: a clinical pilot study10.1098/rsif.2013.0203 ↗
48. Wear resistance of isosit and polymethyl methacrylate occlusal splint material10.1016/S0109-5641(87)80010-6 ↗
49. Evaluation of the effects of the oxygen-inhibited layer on shear bond strength of two resin composites10.4103/0972-0707.48840 ↗
50. Elution study of unreacted Bis-GMA, TEGDMA, UDMA, and Bis-EMA from light-cured dental resins and resin composites using HPLC10.1002/jbm.b.30252 ↗
51. Fracture toughness of denture base acrylics10.1002/jbm.820140403 ↗
52. 3D printing with polymers: challenges among expanding options and opportunities10.1016/j.dental.2015.09.018 ↗
53. Visible light photoinitiator for 3D-printing of tough methacrylate resins10.3390/ma10121445 ↗
54. Effects of irradiance, wavelength, and thermal emission of different light curing units on the Knoop and Vickers hardness of a composite resin10.1002/jbm.b.30929 ↗
55. The future of dental devices is digital10.1016/j.dental.2011.10.014 ↗
56. The anisotropicity of the flexural properties of an occlusal device material processed by stereolithography10.1016/j.prosdent.2016.03.018 ↗
57. The anisotropicity of the flexural properties of an occlusal device material processed by stereolithography10.1016/j.prosdent.2016.03.018 ↗
58. Inkjet printing of drug-loaded mesoporous silica nanoparticles-A platform for drug development10.3390/molecules22112020 ↗
59. Degree of polymerization of resin composites by different light sources10.1046/j.1365-2842.2002.00970.x ↗
60. Computer-assisted orthognathic surgery: feasibility study using multiple CAD/CAM surgical splints10.1016/j.oooo.2011.11.009 ↗