Crack on a chip test method for thin freestanding films
Source abstract
Abstract
Abstract Fracture mechanics has been applied for more than two decades to various configurations of cracks in films on substrate. Fracture toughness data are indeed needed for the design and integrity assessment of many coatings and microelectronics devices. Nevertheless, it is sometimes complicated to deconvolute the constraint exerted by the substrate on the cracking process especially in the presence of viscoelastic or plastic dissipation. Here, a new on chip test method has been developed to determine the fracture toughness of freestanding submicron films. Beside the advantage of avoiding the constraint induced by the substrate, freestanding films allow, if sufficiently thin, direct observation of the fracture mechanisms by transmission electron microscopy. The design of this new nano(micro)-testing consists of two long actuator beams undergoing large internal stress. A specimen is attached to these two actuators, incorporating a notch produced by lithography. Two types of geometries are addressed, one being a double cantilever beam type configuration, while the other is a center cracked panel. Both actuators and specimen are deposited on a sacrificial layer. The etching of the sacrificial layer induces the release of the test structure, with the actuators then contracting and pulling on the test specimen. A crack is initiated from the notch tip, propagates and finally stops when the energy release rate has decreased down to its critical value. This crack arrest measurement avoids the problem of introducing a sufficiently sharp precrack. Analytical equations that describe the stress intensity factor as a function of the geometrical characteristics of the test structures are worked out to guide the dimensional analysis. Extensive finite element analysis provides the full parameter variations necessary to quantify the fracture toughness from experimental data and to capture the process of initiation, unstable cracking and arrest followed by possible further stable propagation. For the sake of a proof of concept, ∼50 and ∼100 nm-thick silicon nitride films produced by low pressure chemical vapor deposition were tested, leading to a mean fracture toughness equal to ∼2 MPa m .
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Metal and Thin Film Mechanics · Advanced Surface Polishing Techniques · Force Microscopy Techniques and Applications
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (43)
Show source-provided references
1. The fracture toughness of polysilicon microdevices: a first report10.1557/JMR.1997.0131 ↗
2. Fracture toughness of polycrystalline silicon carbide thin films10.1063/1.1864246 ↗
3. Cracking of thin bonded films in residual tension10.1016/0020-7683(92)90015-L ↗
4. On-chip tensile testing of nanoscale silicon free-standing beams10.1557/jmr.2011.340 ↗
5. Fracture tests on structural adhesive joints10.1016/S1566-1369(01)80036-4 ↗
6. Internal stress relaxation based method for elastic stiffness characterization of very thin films10.1016/j.tsf.2009.06.062 ↗
7. Brown · 1966
8. Fracture toughness and subcritical crack growth in polycrystalline silicon10.1115/1.2172268 ↗
9. The mechanical strength of polysilicon films: Part 1. The influence of fabrication governed surface conditions10.1016/S0022-5096(03)00051-6 ↗
10. The mechanical strength of polysilicon films: Part 2. Size effects associated with elliptical and circular perforations10.1016/S0022-5096(03)00050-4 ↗
11. Dislocation-mediated relaxation in nanograined columnar palladium films revealed by on-chip time-resolved HRTEM testing10.1038/ncomms6922 ↗
12. Imperfection-sensitive ductility of aluminium thin films10.1016/j.scriptamat.2010.01.048 ↗
13. On-chip stress relaxation testing method for freestanding thin film materials10.1063/1.4758288 ↗
14. A new methodology to investigate fracture toughness of freestanding MEMS and advanced materials in thin film form10.1109/JMEMS.2004.839013 ↗
15. Multipurpose nanomechanical laboratory: five thousands micromachines on a wafer
16. Analysis of a passive sensor for predicting process-induced stress in advanced integrated circuit interconnect10.1109/TDMR.2007.912272 ↗
17. Homogeneous flow and size dependent mechanical behaviour in highly ductile metallic glass films10.1016/j.actamat.2017.03.072 ↗
18. New MEMS – based micromechanical testing laboratory – application to aluminium, polysilicon and silicon nitride10.1109/JMEMS.2009.2020380 ↗
19. Mixed mode cracking in layered materials10.1016/S0065-2156(08)70164-9 ↗
20. In situ micro-cantilever tests to study fracture properties of NiAl single crystals10.1016/j.actamat.2011.10.060 ↗
21. Analysis of stresses and strains near the end of a crack traversing a plate10.1115/1.4011547 ↗
22. Accurate measurement of fracture toughness of freestanding diamond films by three-point bending tests with sharp pre-cracked specimens10.1016/S0925-9635(00)00290-9 ↗
23. Effect of intrinsic stress gradient on the effective mode-I fracture toughness of amorphous diamond-like carbon films for MEMS
24. Electrostatically actuated failure of microfabricated polysilicon fracture mechanics specimens10.1098/rspa.1999.0478 ↗
25. Fracture toughness of polysilicon MEMS devices10.1016/S0924-4247(99)00366-0 ↗
26. Keller · 1998
27. Environmentally assisted cracking in silicon nitride barrier films on poly(ethylene terephthalate) substrates10.1021/acsami.6b06417 ↗
28. Creep behavior of submicron copper films under irradiation10.1016/j.actamat.2017.03.056 ↗
29. A novel on chip test method to characterize the creep behavior of metallic layers under heavy ion irradiation10.1016/j.jnucmat.2016.04.014 ↗
30. The effects of shear on delamination in layered materials10.1016/S0022-5096(03)00070-X ↗
31. Measurement of fracture toughness of ultra-thin amorphous carbon films10.1016/S0040-6090(97)00788-8 ↗
32. Investigation of fracture properties of magnetron-sputtered TiN films by means of a FIB-based cantilever bending technique10.1016/j.actamat.2008.12.018 ↗
33. Fracture toughness of silicon nitride thin films of different thicknesses as measured by bulge tests10.1016/j.actamat.2010.11.043 ↗
34. A versatile lab-on-chip test platform to characterize elementary deformation mechanisms and electromechanical couplings in nanoscopic objects10.1016/j.crhy.2015.11.005 ↗
35. Hemispherical cavities on silicon substrates: an overview of micro fabrication techniques10.1088/2053-1591/aab907 ↗
36. Mode I DCB testing of composite laminates reinforced with z-direction pins: a simple model for the investigation of data reduction strategies10.1016/S0013-7944(03)00116-4 ↗
37. Fracture tests of polysilicon film
38. The tension of metallic films deposited by electrolysis10.1098/rspa.1909.0021 ↗
39. Tada · 2000
40. Tensile strength and fracture toughness of surface micromachined polycrystalline silicon thin films prepared under various conditions
41. On-chip fracture testing of freestanding nanoscale materials10.1016/j.engfracmech.2015.07.006 ↗
42. A new bulge test technique for the determination of Young's modulus and Poisson's ratio of thin films10.1557/JMR.1992.3242 ↗
43. Plane-strain bulge test for thin films10.1557/jmr.2005.0313 ↗