journal article·2012-09

Investigation of Deposition Behavior of Cold-Sprayed Magnesium Coating

X. K. Suo, X. P. Guo, W. Y. Li, M. P. Planche, H. L. Liao

Publisher page

Abstract

Two types of magnesium powders with different particle size distributions were deposited by cold spraying at different main gas temperatures. The effects of gas temperature and particle size distribution on the deposition efficiency of particles were studied. The microstructure of coatings was observed, and the porosity of coatings was evaluated. The deposition efficiency of particles increased, and the porosity of coatings decreased with the increase of gas temperature. The deposition efficiency of particles increased when using the powder with a smaller particle size distribution. Stainless steel and aluminum plates were used as substrates. The bonding strength and mechanism between the coating and substrate were studied. The commercial finite element software ABAQUS was used to help us better understand the deformation behavior of particles and substrates. The mean bonding strength slightly increased when aluminum plates were used as substrates. The bonding mechanism of Mg coatings on stainless steel and aluminum substrates was discussed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Flame retardant materials and properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. Z. Yang, J.P. Li, J.X. Zhang, G.W. Lorimer, and J. Robson, Review on Research and Development of Magnesium Alloys, Acta Metall. Sin. (Engl. Lett.), 2008, 21(5), p 313-32810.1016/S1006-7191(08)60054-X ↗
2. J.A. Francis and G.M.D. Cantin, The Role of Defects in the Fracture of An Al-Si-Mg Cast Alloy, Mater. Sci. Eng. A, 2005, 407(1-2), p 322-32910.1016/j.msea.2005.07.042 ↗
3. W. Xiao, S. Jia, L. Wang, Y. Wu, and L. Wang, The Microstructures and Mechanical Properties of Cast Mg-Zn-Al-RE Alloys, J. Alloy Compd., 2009, 480(2), p L33-L3610.1016/j.jallcom.2009.02.087 ↗
4. T. Hussain, D.G. McCartney, P.H. Shipway, and D. Zhang, Bonding Mechanisms in Cold Spraying: The Contributions of Metallurgical and Mechanical Components, J. Therm. Spray Technol., 2009, 18(3), p 364-37910.1007/s11666-009-9298-1 ↗
5. T.H. Van Steenkiste, J.R. Smith, R.E. Teets, J.J. Moleski, D.W. Gorkiewicz, R.P. Tison et al., Kinetic Spray Coatings, Surf. Coat. Technol., 1999, 111(1), p 62-7110.1016/S0257-8972(98)00709-9 ↗
6. P. Richer, B. Jodoin, and L. Ajdelsztajn, Substrate Roughness and Thickness effects on Cold Spray Nanocrystalline Al-Mg Coatings, J. Therm. Spray Technol., 2006, 15(2), p 246-25410.1361/105996306X108174 ↗
7. H. Assadi, F. Gätner, T. Stoltenhoff, and H. Kreye, Bonding Mechanism in Cold Gas Spraying, Acta Mater., 2003, 51(15), p 4379-439410.1016/S1359-6454(03)00274-X ↗
8. C.J. Li, W.Y. Li, and H.L. Liao, Examination of the Critical Velocity for Deposition of Particles in Cold Spraying, J. Therm. Spray Technol., 2006, 15(2), p 212-22210.1361/105996306X108093 ↗
9. T. Schmidt, F. Gärtner, H. Assadi, and H. Kreye, Development of a Generalized Parameter Window for Cold Spray Deposition, Acta Mater., 2006, 54(3), p 729-74210.1016/j.actamat.2005.10.005 ↗
10. A. Sova, V. Kosarev, S. Klinkov, and I. Smurou, Location of the Powder Injection as Independent Parameter to Control Particle Velocity and Temperature in Cold Spray, International Thermal Spraying Conference 2010 (Singapore), 2010, p 801-80510.31399/asm.cp.itsc2010p0786 ↗
11. B. Jodoin, Cold Spray Nozzle Mach Number Limitation, J. Therm. Spray Technol., 2002, 11(4), p 496-50710.1361/105996302770348628 ↗
12. M.F. Smith, J.E. Brockmann, R.C. Dykhuizen, D.L. Gilmore, R.A. Neiser, and T.J. Roemer, Cold Spray Direct Fabrication—High Rate, Solid State, Material Consolidation, Proceedings of the Material Research Society Fall Meeting (Boston), 1998, p 65-7610.1557/PROC-542-65 ↗
13. M. Grujicic, J.R. Saylor, D.E. Beasley, W.S. DeRosset, and D. Helfritch, Computational Analysis of the Interfacial Bonding Between Feed-powder Particles and the Substrate in the Cold-Gas Dynamic-Spray Process, Appl. Surf. Sci., 2003, 219(3-4), p 211-22710.1016/S0169-4332(03)00643-3 ↗
14. S. Rech, A. Trentin, S. Vezzù, J.-G. Legoux, E. Irissou, and M. Guagliano, Influence of Pre-heated Al 6061 Substrate Temperature on the Residual Stresses of Multipass Al Coatings Deposited by Cold Spray, J. Therm. Spray Technol., 2011, 20(1), p 243-25110.1007/s11666-010-9596-7 ↗
15. M. Fukumoto, H. Wada, K. Tanabe, M. Yamada, E. Yamaguchi, A. Niwa, M. Sugimoto, and M. Izawa, Effect of Substrate Temperature on Deposition Behavior of Copper Particles on Substrate Surfaces in the Cold Spray Process, J. Therm. Spray Technol., 2007, 16(5), p 643-65010.1007/s11666-007-9121-9 ↗
16. D. Christoulis, S. Guetta, V. Guipont, and M. Jeandin, The Influence of the Substrate on the Deposition of Cold-sprayed Titanium: An Experimental and Numerical Study, J. Therm. Spray Technol., 2011, 20(3), p 523-53310.1007/s11666-010-9608-7 ↗
17. X. Suo, X. Guo, W. Li, M.-P. Planche, R. Bolot, H. Liao, and C. Coddet, Preparation and Characterization of Magnesium Coating Deposited by Cold Spraying, J. Mater. Process. Technol., 2012, 212(1), p 100-10510.1016/j.jmatprotec.2011.08.010 ↗
18. W.Y. Li, H. Liao, C.J. Li, G. Li, C. Coddet, and X.F. Wang, On High Velocity Impact of Micro-sized Metallic Particles in Cold Spraying, Appl. Surf. Sci., 2006, 253(5), p 2852-286210.1016/j.apsusc.2006.05.126 ↗
19. S. Yin, X.F. Wang, W.Y. Li, and H.E. Jie, Effect of Substrate Hardness on the Deformation Behavior of Subsequently Incident Particles in Cold Spraying, Appl. Surf. Sci., 2011, 257(17), p 7560-756510.1016/j.apsusc.2011.03.126 ↗
20. M. Yu, W.-Y. Li, F.F. Wang, and H.L. Liao, Finite Element Simulation of Impacting Behavior of Particles in Cold Spraying by Eulerian Approach, J. Therm. Spray Technol., 2011, doi: 10.1007/s11666-011-9717-y10.1007/s11666-011-9717-y ↗
21. D. Hasenpouth, “Tensile High Strain Rate Behavior of AZ31B Magnesium Alloy Sheet,” Master thesis, Mechanical Engineering, University of Waterloo, 201010.1051/dymat/2009202 ↗
22. S.G. Hibbins, Proceedings of the International Symposium on Light Metals, The Metallurgical Society of CIM, 1998, p 265