journal article·2017-08

The Influence of Composition and Microstructure on the Abradability of Aluminum-Based Abradable Coatings

Jianming Liu, Yueguang Yu, Tong Liu, Xuying Cheng, Jie Shen, Changhai Li

Publisher page

Abstract

Five kinds of commercial aluminum-based abradable coatings including AlSi, Al-hBN, AlSi-polyester, AlSihBN and Al-AlSi-hBN were fabricated to perform parallel abradability tests rubbed against Ti6Al4V dummy blades at high temperature up to 450 °C and high velocity up to 300 m/s conditions. AlSi coating, which contains no additional secondary filler, only showed acceptable abradability at medium incursion rate under 450 °C, and severe blade wear or coating transfer to blade tip occurred at low and high incursion rates. Other four coatings which contain secondary fillers performed far beyond AlSi coating. It was found that not only the amount added but also the diameter of secondary fillers plays an important role in coating abradability. For the similar filler addition level, Al-hBN and Al-AlSi-hBN coatings which contain fine filler performed much better than AlSi-hBN coating with coarse filler. Shorter filler spacing in the fine filler samples is concluded to be the reason for better abradability.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Metal and Thin Film Mechanics · High-Temperature Coating Behaviors · Surface Treatment and Residual Stress

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (22)

Show source-provided references
1. R.E. Chupp, R.C. Hendricks, S.B. Lattime, and B.M. Steinetz, Sealing in Turbomachinery, J. Propul. Power, 2006, 22(2), p 313-34910.2514/1.17778 ↗
2. S. Wilson, Thermally sprayed abradable coating technology for sealing in gas turbines, The Future of Gas Turbine Technology, 6th International Conference, 17-18 October 2012, Brussels, Belgium, Paper ID Number 51.
3. W.D. Marscher and C. Osborne, Abradable Turbine Shroud Development, Final Report, TN-343, Creare Inc., 1983.
4. N. Hopkins, The Black Art of Abradable Coatings, PEI, 2007, 15(4), p 50-52
5. X. Ma and A. Matthews, Investigation of Abradable Seal Coating Performance Using Scratch Testing, Surf. Coat. Technol., 2007, 202(4-7), p 1214-122010.1016/j.surfcoat.2007.07.076 ↗
6. R.E. Johnston and W.J. Evans, Freestanding Abradable Coating Manufacture and Tensile Test Development, Surf. Coat. Technol., 2007, 202(4-7), p 725-72910.1016/j.surfcoat.2007.05.082 ↗
7. R.E. Johnston, The Sensitivity of Abradable Coating Residual Stresses to Varying Material Properties, J. Thermal Spray Technol., 2009, 18(5), p 1004-101310.1007/s11666-009-9378-2 ↗
8. R. Bolot and J.-L. Seichepine, Predicting the Thermal Conductivity of AlSi/Polyester Abradable Coatings: Effects of the Numerical Method, J. Thermal Spray Technol., 2011, 20(1), p 39-4710.1007/s11666-010-9592-y ↗
9. M. Dorfman, U. Erning, and J. Mallon, Gas Turbines Use ‘Abradable’ Coatings for Clearance-Control Seals, Seal. Technol., 2002, 97, p 7-810.1016/S1350-4789(02)80002-2 ↗
10. R.K. Schmid, New High Temperature Abradables for Gas Turbines (Diss. ETH No. 1223, 1997), p. 83-89.
11. R.C. Schwab, Program to Develop Sprayed, Plastically Deformable Compressor Shroud Seal Materials, 1979, NAS3-20054, CR159741.
12. E. Irissou, A. Dadouche, and R.S. Lima, Tribological Characterization of Plasma-Sprayed CoNiCrAlY-BN Abradable Coatings, J. Thermal Spray Technol., 2014, 23(1), p 252-26110.1007/s11666-013-9998-4 ↗
13. D. Aussavy, R. Bolot, and G. Montavon, YSZ-Polyester Abradable Coatings Manufactured by APS, J. Thermal Spray Technol., 2016, 25(1), p 252-26310.1007/s11666-015-0358-4 ↗
14. T.A. Taylor, B.W. Thompson, and W. Aton, High Speed Rub Wear Mechanism in IN-718 Vs. NiCrAl-Bentonite, Surf. Coat. Technol., 2007, 202(4-7), p 698-70310.1016/j.surfcoat.2007.05.054 ↗
15. J. Stringer and M.B. Marshall, High Speed Wear Testing of An Abradable Coating, Wear, 2012, 294-295, p 257-26310.1016/j.wear.2012.07.009 ↗
16. H. Wang, Criteria for Analysis of Abradable Coatings, Surf. Coat. Technol., 1996, 79(1), p 71-7510.1016/0257-8972(95)02443-3 ↗
17. U. Bardi, C. Giolli, A. Scrivani, and G. Rizzi, Development and Investigation on New Composite and Ceramic Coatings as Possible Abradable Seals, J. Thermal Spray Technol., 2008, 17(5), p 805-81110.1007/s11666-008-9246-5 ↗
18. C.-J. Li, J. Zou, H.-B. Huo, and J.-T. Yao, Microstructure and Properties of Porous Abradable Alumina Coatings Flame-Sprayed with Semi-molten Particles, J. Thermal Spray Technol., 2016, 25(1), p 264-272
19. R.K. Schmid, F. Ghasripoor, M. Dofman, and X. Wei, An Overview of Compressor Abradables, Proc. 1st International Thermal Spray Conference, May 8-11, 2000 (Montreal, Canada), p 1087-1093.10.31399/asm.cp.itsc2000p1087 ↗
20. N. Fois and M.B.Marshall. Stringer, Adhesive Transfer in Aero-engine Abradable Lings Contact, Wear, 2013, 304, p 202-21010.1016/j.wear.2013.04.033 ↗
21. W.H. Xue, S.Y. Gao, and D.L. Duan, Material Transfer Behavior Between a Ti6Al4V Blade and An Aluminum Hexagonal Boron Nitride Abradable Coating During High-Speed Rubbing, Wear, 2015, 322-323, p 76-9010.1016/j.wear.2014.10.001 ↗
22. M. Bounazef, S. Guessasma, and B.A. Saadi, The Wear, Deterioration and Transformation Phenomena of Abradable Coating BN-SiAl-Bounding Organic Element, Caused by the Friction between the Blades and the Turbine Casing, Mater. Lett., 2004, 58(27-28), p 3375-338010.1016/j.matlet.2004.02.049 ↗