journal article·2021-01

High Rate Deposition in Cold Spray

Ozan C. Ozdemir, Patricia Schwartz, Sinan Muftu, Forest C. Thompson, Grant A. Crawford, Aaron T. Nardi, Victor K. Champagne, Christian A. Widener

Journal of Thermal Spray Technology· Volume 30· Issue 1-2
Publisher page

Abstract

Industrialization of cold spray introduces concerns regarding the cost and time efficiency of cold spray procedures. In this work, high rate deposition of tantalum was studied computationally and experimentally. Quasi-1D multiphase fluid simulations predicted minimal effects on the bonding conditions of particles with 5% to 14% increase in powder-to-gas mass flow ratio. Experimental specimens were produced to observe the mechanical and microstructural effects of increased powder stream loading. Adhesion and hardness tests as well as thermal conductivity, optical microscopy, and electron backscatter diffraction examinations only exhibited minor differences in the mechanical and microstructural properties of the specimens. The increased powder stream loading rate, however, allows a significant reduction in the time required for depositing the same amount of tantalum by a factor of three. The results of the study enable shorter cold spray deposition time. This leads to significant cost savings associated with consumption of helium and labor, while facilitating shorter turn-around times for repairing components and manufacturing of cold-sprayed products.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Fluid Dynamics and Heat Transfer · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (41)

Show source-provided references
1. K. Woock, Safeguarding our helium supply, Imaging Economicsed., 2013, p 8
2. The World Is Constantly Running Out Of Helium. Here’s Why It Matters., (NPR) https://www.npr.org/2019/11/01/775554343/the-world-is-constantly-running-out-of-helium-heres-why-it-matters. (Accessed 18 February 2020 2020)
3. O.C. Ozdemir, C.A. Widener, M.J. Carter, and K.W. Johnson, Predicting the Effects of Powder Feeding Rates on Particle Impact Conditions and Cold Spray Deposited Coatings, J. Therm. Spray Technol., 2017, 26(7), p 1598-161510.1007/s11666-017-0611-0 ↗
4. O. Stier, Fundamental Cost Analysis of Cold Spray, J. Therm. Spray Technol., 2014, 23(1), p 131-13910.1007/s11666-013-9972-1 ↗
5. H. Gabel, Kinetic metallization compared with HVOF. (Tech Spotlight), Adv. Mater. Processes, 2004, 162(5), p 47
6. M.C. Meyer, S. Yin, K.A. McDonnell, O. Stier, and R. Lupoi, Feed Rate Effect on Particulate Acceleration in Cold Spray Under Low Stagnation Pressure Conditions, Surf. Coat. Technol., 2016, 304, p 237-24510.1016/j.surfcoat.2016.07.017 ↗
7. K. Taylor, B. Jodoin, J. Karov, Particle Loading Effect in Cold Spray, J. Therm. Spray Technol., 15(2), (2005)10.1361/105996306X108237 ↗
8. D.L. Gilmore, R.C. Dykhuizen, R.A. Neiser, T.J. Roemer, and M.F. Smith, Particle Velocity and Deposition Efficiency in the Cold Spray Process, J. Therm. Spray Technol., 1999, 8(4), p 576-58210.1361/105996399770350278 ↗
9. T. Schmidt, H. Assadi, F. Gartner, H. Richter, T. Stoltenhoff, H. Kreye, and T. Klassen, From Particle Acceleration to Impact and Bonding in Cold Spraying, J. Therm. Spray Technol., 2009, 18(5–6), p 794-80810.1007/s11666-009-9357-7 ↗
10. V. Champagne, The Cold Spray Materials Deposition Process: Fundamentals and Applications, Woodhead Publishing Limited, Sawston, 2007, p 1-36210.1201/9781439824122 ↗
11. A. Moridi, S.M. Hassani-Gangaraj, S. Vezzu, and M. Guagliano, Number of Passes and Thickness Effect on Mechanical Characteristics of Cold Spray Coating, Procedia Eng., 2014, 74, p 449-45910.1016/j.proeng.2014.06.296 ↗
12. S. Rech, A. Trentin, S. Vezzù, E. Vedelago, J.-G. Legoux, and E.J.J.O.T.S.T. Irissou, Different Cold Spray Deposition Strategies: Single- and Multi-layers to Repair Aluminium Alloy Components, J Thermal Spray Technol, 2014, 23(8), p 1237-125010.1007/s11666-014-0141-y ↗
13. S.M. Cardonne, P. Kumar, C.A. Michaluk, and H.D. Schwartz, Tantalum and Its Alloys, Int. J. Refract. Met. Hard Mater., 1995, 14, p 187-19410.1016/0263-4368(95)94023-R ↗
14. J. Kim, G. Bae, and C. Lee, Characteristics of Kinetic Sprayed Ta in Terms of the Deposition Behavior, Microstructural Evolution and Mechanical Properties: Effect of Strain-Ratedependent Response of Ta at High Temperature, Mater. Charact., 2018, 141, p 49-5810.1016/j.matchar.2018.04.023 ↗
15. M.D. Trexler, R. Carter, W.S. De Rosset, D. Gray, D. Helfritch, and V.K. Champagne, Cold Spray Fabrication of Refractory Materials for Gun Barrel Liner Applications, Mater. Manuf. Processes, 2012, 27, p 820-82410.1080/10426914.2011.648690 ↗
16. Spotlight on Turbulence: STAR-CCM + v11.06, (Siemens PLM Software) https://steve.cd-adapco.com/articles/en_US/FAQ/Spotlight-on-Turbulence
17. STAR-CCM + Release Notes v11.06, (Siemens PLM Software) https://steve.cd-adapco.com/. (Accessed 4 Jul 2017 2017)
18. J.D.J. Anderson, Computational Fluid Dynamics: The Basics with Applications, McGraw-Hill Inc., New York, 1995, p 1-547
19. R.B. Bird, W.E. Stewart, E.N. Lightfoot, Transport Phenomena, 2 ed., John Wiley and Sons, Inc, 2002, p 27, 276, 439
20. F.R. Menter, Review of the Shear Stress Transport Turbulence Model Experience from an Industrial Perspective, Int. J. Comput. Fluid Dyn., 2009, 23(4), p 305-31610.1080/10618560902773387 ↗
21. H. Schlichting, Boundary Layer Theory, 7 ed., F.J. Cerra, Ed., McGraw-Hill Book Company, Inc, 1987, p 596–667
22. J.F. Wendt, Computational Fluid Dynamics: An Introduction, 3rd ed., Springer, Berlin, 200910.1007/978-3-540-85056-4 ↗
23. S. Martin and J.R. Williams, Multiphase Flow Research, Nova Science Publishers Inc., New York, 2009
24. J.D. Anderson, Modern Compressible Flow with Historical Perspective, McGraw-Hill Inc., New York, 2012
25. T. Schmidt, F. Gartner, H. Assadi, and H. Kreye, Development of a Generalized Parameter Window for Cold Spray Deposition, Acta Mater., 2006, 54, p 729-74210.1016/j.actamat.2005.10.005 ↗
26. ASTM, Standard Guide for Preparation of Metallogrophic Specimens, ASTM E3, ASTM International 2017
27. ASTM, Standard Methods for Determining Area Percentage Porosity in Thermally Sprayed Coatings, ASTM E2109 - 01, ASTM International 2014
28. ImageJ, https://imagej.net/ImageJ. (Accessed 7 Jan 2019 2019)
29. B. Li, L. Hou, R. Wu, J. Zhang, X. Li, M. Zhang, A. Dong, and B. Sun, Microstructure and Thermal Conductivity of Mg-2Zn-Zr Alloy, J. Alloys Compd., 2017, 722, p 772-77710.1016/j.jallcom.2017.06.148 ↗
30. E. Vandersluis, A. Lombardi, C. Ravindran, A. Bois-Brochu, F. Chiesa, and R. MacKay, Factors Influencing Thermal Conductivity and Mechanical Properties in 319 Al Alloy Cylinder Heads, Mater. Sci. Eng. A, 2015, 648, p 40110.1016/j.msea.2015.09.091 ↗
31. C. Yang, F. Pan, X. Chen, N. Luo, B. Han, and T. Zhou, Thermal Conductivity and Mechanical Properties of Sm-Containing Mg-Zn-Zr Alloys, Mater. Sci. Technol., 2018, 34(2), p 138-14410.1080/02670836.2017.1366707 ↗
32. D. Seo, K. Ogawa, K. Sakaguchi, N. Miyamoto, and Y. Tsuzuki, Parameter Study Influencing Thermal Conductivity of Annealed Pure Copper Coatings Deposited by Selective Cold Spray Processes, Surf. Coat. Technol., 2012, 206(8–9), p 2316-232410.1016/j.surfcoat.2011.10.010 ↗
33. S.E. Gustafsson, Transient Plane Source Techniques for Thermal Conductivity and Thermal Diffusivity Measurements of Solid Materials, Rev. Sci. Instrum., 1991, 62(3), p 797-80410.1063/1.1142087 ↗
34. Hot Disk Thermal Constants Analyser Instruction Manual, Hot Disk, Göteborg, Sweden, 2019
35. V. Livescu, J.F. Bingert, and T.A. Mason, Deformation Twinning in Explosively-Driven Tantalum, Mater. Sci. Eng. A, 2012, 556, p 155-16310.1016/j.msea.2012.06.071 ↗
36. ASM Handbook Volume 02 - Properties and Selection: Nonferrous Alloys and Special-Purpose Materials, ed., ASM International, 1990
37. G. Bolelli, B. Bonferroni, H. Koivuluoto, L. Lusvarghi, and P. Vuoristo, Depth-Sensing Indentation for Assessing the Mechanical Properties of Cold-Sprayed Ta, Surf. Coat. Technol., 2010, 205(7), p 2209-221710.1016/j.surfcoat.2010.08.146 ↗
38. S. Kumar, V. Vidyasagar, A. Jyothirmayi, and S. Joshi, Effect of Heat Treatment on Mechanical Properties and Corrosion Performance of Cold-Sprayed Tantalum Coatings, J. Therm. Spray Technol., 2016, 25(4), p 745-75610.1007/s11666-016-0388-6 ↗
39. M.R. Rokni, S.R. Nutt, C.A. Widener, V.K. Champagne, R.H. Hrabe, Review of Relationship Between Particle Deformation, Coating Microstructure, and Properties in High-Pressure Cold Spray, J. Therm. Spray Technol., (2017)10.1007/s11666-017-0575-0 ↗
40. C.A. Widener, M.J. Carter, O.C. Ozdemir, R.H. Hrabe, B. Hoiland, T.E. Stamey, V.K. Champagne, and T.J. Eden, Application of High-Pressure Cold Spray for an Internal Bore Repair of a Navy Valve Actuator, J. Therm. Spray Technol., 2016, 25(1–2), p 193-20110.1007/s11666-015-0366-4 ↗
41. B.L. James, B-1 Cold Spray Initiative, Cold Spray Action Team Meeting, (Worcester, MA, USA, 2016)