The Effect of Water Film Surrounding the Deposited Particle on Bonding Area: A Numerical Study
Source abstract
Abstract
Cold spray (CS) is a thermal spray method that deposits solid particles at high velocity at about room temperature using gases such as nitrogen or helium. Despite of CS’s unique advantages, it is expensive to operate due to its high gas consumption and the need for small particle sizes for deposition. To enhance cost-effectiveness, liquid cold spray (LCS) has been developed with the capability of depositing large particles with a wider size cut by using water as a propellant. Though LCS has demonstrated success in manufacturing copper coatings, it raises questions about how wetting of particles and/or substrate surfaces can affect adhesion. This paper addresses these concerns using a finite element method based on elastic–plastic theory. Results demonstrate that wetting the deposited particle reduces both particle and substrate deformation. Water film wetting the particle primarily affects the bonding area due to its presence in the interfacial area between the particle and substrate. In order to avoid interfacial water, this paper investigates the effect of four parameters as follows: particle velocity, particle size, water film thickness, and water temperature. The results demonstrate that the volume of interfacial water is reduced by increasing particle impact velocity and particle size and decreasing water film thickness. A rise in water temperature does not affect the amount of interfacial water; however, evaporation of interfacial water can increase.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: High-Temperature Coating Behaviors · Particle Dynamics in Fluid Flows · Fluid Dynamics and Heat Transfer
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (38)
Show source-provided references
1. X. Yan, C. Huang, C. Chen, R. Bolot, L. Dembinski, R. Huang, W. Ma, H. Liao, and M. Liu, Additive Manufacturing of WC Reinforced Maraging Steel 300 Composites by Cold Spray and Selective Laser Melting, Surf. Coat. Technol., 2019, 371, p 161-171.10.1016/j.surfcoat.2018.03.072 ↗
2. F. Khodabakhshi, B. Marzbanrad, H. Jahed, and A.P. Gerlich, Interfacial Bonding Mechanisms between Aluminum and Titanium during Cold Gas Spraying Followed by Friction-Stir Modification, Appl. Surf. Sci., 2018, 462, p 739-752.10.1016/j.apsusc.2018.08.156 ↗
3. D. Goldbaum, J.M. Shockley, R.R. Chromik, A. Rezaeian, S. Yue, J. Legoux, and E. Irissou, The Effect of Deposition Conditions on Adhesion Strength of Ti and Ti6Al4V Cold Spray Splats, J. Therm. Spray Technol., 2012, 21, p 288.10.1007/s11666-011-9720-3 ↗
4. S. Bagherifard, S. Monti, M.V. Zuccoli, M. Riccio, J. Kondas, and M. Guagliano, Cold Spray Deposition for Additive Manufacturing of Freeform Structural Components Compared to Selective Laser Melting, Mater. Sci. Eng. A, 2018, 721, p 339-350.10.1016/j.msea.2018.02.094 ↗
5. C. Chen, Y. Xie, X. Yan, S. Yin, H. Fukanuma, R. Huang, R. Zhao, J. Wang, Z. Ren, M. Liu, and H. Liao, Effect of Hot Isostatic Pressing (HIP) on Microstructure and Mechanical Properties of Ti6Al4V Alloy Fabricated by Cold Spray Additive Manufacturing, Addit. Manuf., 2019, 27, p 595-605.
6. P.L. Fauchais, J.V.R. Heberlein, and M.I. Boulos, Thermal Spray Fundamentals from Powders to Parts, 1st ed. Springer, New York, 2015.
7. S. Rahmati and B. Jodoin, Physically Based Finite Element Modeling Method to Predict Metallic Bonding in Cold Spray, J. Therm. Spray Technol., 2020, 29, p 611-629.10.1007/s11666-020-01000-1 ↗
8. Y. Xie, S. Yin, C. Chen, M. Planche, H. Liao, and R. Lupoi, New Insights into the Coating/Substrate Interfacial Bonding Mechanism in Cold Spray, Scripta Mater., 2016, 125, p 1-4.10.1016/j.scriptamat.2016.07.024 ↗
9. W. Li, H. Liao, C. Li, H. Bang, and C. Coddet, Numerical Simulation of Deformation Behavior of Al Particles Impacting on Al Substrate and Effect of Substrate Oxide Films on Interfacial Bonding in Cold Spraying, Appl. Surf. Sci., 2007, 253, p 5084-5091.10.1016/j.apsusc.2006.11.020 ↗
10. T. Schmidt, F. Gartner, H. Assadi, and H. Kreye, Development of a Generalized Parameter Window for Cold Spray Deposition, Acta Mater., 2006, 54, p 729-742.10.1016/j.actamat.2005.10.005 ↗
11. M. Hassani-Gangaraj, D. Veysset, V.K. Champagne, K.A. Nelson, and C.A. Schuh, Adiabatic Shear Instability is not Necessary for Adhesion in Cold Spray, Acta Mater., 2018, 158, p 430-439.10.1016/j.actamat.2018.07.065 ↗
12. C.J. Huang, H.J. Wu, Y.C. Xie, W.Y. Li, C. Verdy, M.P. Planche, H.J. Liao, and G. Montavon, Advanced Brass-Based Composites via Cold-Spray Additive-Manufacturing and its Potential in Component Repairing, Surf. Coat. Technol., 2019, 371, p 211-223.10.1016/j.surfcoat.2019.02.034 ↗
13. S. Yin, P. Cavaliere, B. Aldwell, R. Jenkins, H. Liao, W. Li, and R. Lupoi, Cold Spray Additive Manufacturing and Repair: Fundamentals and Applications, Addit. Manuf., 2018, 21, p 628-650.
14. A. Sova, S. Grigoriev, A. Okunkova, and I. Smurov, Potential of Cold Gas Dynamic Spray as Additive Manufacturing Technology, Int. J. Adv. Manuf. Technol., 2013, 69, p 2269-2278.10.1007/s00170-013-5166-8 ↗
15. N.H. Tariq, L. Gyansah, J.Q. Wang, X. Qiu, B. Feng, M.T. Siddique, and T.Y. Xiong, Cold Spray Additive Manufacturing: A Viable Strategy to Fabricate Thick B4C/Al Composite Coating for Neutron Shielding Application, Surf. Coat. Technol., 2018, 339, p 224-236.10.1016/j.surfcoat.2018.02.007 ↗
16. J. Xie, Simulation of Cold Spray Particle Deposition Process. Thèse, Le Grade de Docteur, L’institut national des sciences appliquées de Lyon, 2014.
17. R. Chakrabarty and J. Song, Crystal Plasticity Finite Element Investigation of Deformation of Single Crystal Copper During Cold Spay, Addit. Manuf., 2022, 49, p 102484.
18. Y. Kim and K. Lee, Effect of Carrier Gas Species on the Microstructure and Compressive Deformation Behaviors of Ultra-Strong Pure Copper Manufactured by Cold Spray Additive Manufacturing, J. Mater. Sci. Technol., 2022, 97, p 264-271.10.1016/j.jmst.2021.04.062 ↗
19. S. Rahmati, R.G.A. Veiga, A. Zuniga, and B. Jodoin, A Numerical Approach to Study the Oxide Layer Effect on Adhesion in Cold Spray, J. Therm. Spray Technol., 2021, 30(7), p 1777.10.1007/s11666-021-01245-4 ↗
20. T. Butler, Liquid Accelerated Cold Spray, Cold Spray Action Team (CSAT), 2011.
21. T. Butler, Liquid Accelerated Cold Spray, Cold Spray Action Team (CSAT), 2012.
22. A. Akbarnozari, S. Garmeh, F. Ben Attouil, A. Dolatabadi, S. Desaulniers, L. Pouliot, and C. Moreau, Recent Advance in Liquid Cold Spray (LCS), North American Cold Spray Conference, (New Orleans, 2022).
23. S. Rahmati and A. Ghaei, The Use of Particle/Substrate Material Models in Simulation of Cold-Gas Dynamic-Spray Process, J. Therm. Spray Technol., 2014, 23, p 530-540.10.1007/s11666-013-0051-4 ↗
24. B. Buck, Y. Tang, N.G. Deen, J.A.M. Kuipers, and S. Heinrich, Dynamics of Wet Particle-Wall Collisions: Influence of Wetting Condition, Chem. Eng. Res. Des., 2018, 135, p 21-29.10.1016/j.cherd.2018.05.014 ↗
25. L. Zhang and C. Wu, Discrete Element Analysis of Normal Elastic Impact of Wet Particles, Powder Technol., 2020, 362, p 628-634.10.1016/j.powtec.2019.12.021 ↗
26. D. Wu, P. Zhou, G. Wang, T. Howes, and W. Chen, A Theoretical Study of Particle Coalescence Criteria for Inelastic Collision of Wet Particles, Chem. Eng. Sci., 2021, 243, p 116770.10.1016/j.ces.2021.116770 ↗
27. T. Kondo and K. Ando, Simulation of High-Speed Droplet Impact Against a Dry/Wet Rigid Wall for Understanding the Mechanism of Liquid Jet Cleaning, Phys. Fluids, 2019, 31, p 013323.10.1063/1.5079282 ↗
28. B. Buck, Y. Tang, S. Heinrich, N.G. Deen, and J.A.M. Kuipers, Collision Dynamics of Wet Solids: Rebound and Rotation, Powder Technol., 2017, 316, p 218-224.10.1016/j.powtec.2016.12.088 ↗
29. C. Henry and J. Minier, Progress in Particle Resuspension from Rough Surfaces by Turbulent Flows, Prog. Energy Combust. Sci., 2014, 45, p 1-53.10.1016/j.pecs.2014.06.001 ↗
30. B. Buck, J. Lunewski, Y. Tang, N.G. Deen, J.A.M. Kuipers, and S. Heinrich, Numerical Investigatoin of Collision Dynamics of Wet Particles via Force balance, Chem. Eng. Res. Des., 2018, 132, p 1143-1159.10.1016/j.cherd.2018.02.026 ↗
31. P. Khamsepour, A. Akbarnozari, S. Garmeh, C. Moreau, and A. Dolatabadi, The Effect of Water Layer Covering Substrate Surface on the Deformation of the Impacting Particle Deposited by Liquid Cold Spray, Canadian Society for Mechanical Engineering International Congress, Alberta, 2022.
32. Y. Liu, C.X. Li, X.F. Huang, K. Ma, X.T. Luo, and C.J. Li, Effect of Water Environment on Particle Deposition of Underwater Cold Spray, Appl. Surf. Sci., 2020, 506, p 144542.10.1016/j.apsusc.2019.144542 ↗
33. Y. Meng, H. Saito, C. Bernard, Y. Ichikawa, and K. Ogawa, Parametric Study to Repair Leaks in Water Pipe Using the Low-Pressure Cold Spray Technique, J. Therm. Spray Technol., 2022, 31, p 2560-2576.10.1007/s11666-022-01469-y ↗
34. J. Xie, D. Nelias, H.W. Berre, K. Ogawa, and Y. Ichikawa, Simulation of the Cold Spray Particle Deposition Process, Journal of Tribology, 2015, 137, p 041101.10.1115/1.4030257 ↗
35. Dassault Systemes, ABAQUS Analysis User’s Manuel, 6.9. Simulia, Johnston, 2011.
36. O.C. Oxdemir, J.M. Conahan, and S. Muftu, Particle Velocimetry CFD, and the Role of Particle Sphericity in Cold Spray, Coatings, 2020, 10, p 1254.10.3390/coatings10121254 ↗
37. P. Khamsepour, C. Moreau, and A. Dolatabadi, Numerical Simulation of the Effect of Particle and Substrate Pre-Heating on Porosity Level and Residual Stress of As-Sprayed Ti6Al4V Components, J. Therm. Spray Technol., 2021, 13, p 1-14.
38. H. Assadi, T. Schmidt, H. Richter, J.-O. Kliemann, K. Binder, F. Gärtner, T. Klassen, and H. Kreye, On Parameter Selection in Cold Spraying, J. Therm. Spray Technol., 2011, 20, p 1161-1176.10.1007/s11666-011-9662-9 ↗