journal article·2014-10-04

Mechanical Properties of Cu-0.1Ag Alloys Deposited by Cold Spray with Various Powder Feed Rate and Heat Treatment

Pierre Coddet, Christophe Verdy, Christian Coddet, François Debray

Publisher page

Abstract

This work focuses on the properties of Cu-Ag alloys deposited by a cold spray process. Helium was used as the carrier gas and main gas to reach particles velocity of 823 m/s, which is in the middle range of the deposition window for Cu alloys. A closed loop circuit avoiding costly helium losses was implemented. Thus, deposition efficiency higher than 95%, porosity below 0.1%, and oxygen content below 150 ppm were obtained. The influence of the deposition parameters on microstructure, mechanical properties (ultimate tensile strength, yield strength, elongation, hardness), and residual stress level in the material was studied. Intensive work hardening mechanisms are involved by comparison with classically forged material allowing a large tailoring of the material’s properties through specific heat treating.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: High-Temperature Coating Behaviors · Advanced materials and composites · Advanced ceramic materials synthesis

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (19)

Show source-provided references
1. A.N. Papyrin, Cold Spray Technology—Cold Spray Products High Quality Coatings for a Wide Spectrum of Applications, Adv. Mater. Process., 2001, 159, p 49-51
2. D.L. Gilmore, R.C. Dykhuizen, R.A. Neiser, T.J. Roemer, and M.F. Smith, Particle Velocity and Deposition Efficiency in the Cold Spray Process, J. Therm. Spray Technol., 1999, 8, p 576-58210.1361/105996399770350278 ↗
3. Safety Standard for Hydrogen and Hydrogen Systems, NASA, NSS 1740.16, 1997
4. G. Ghosh, J. Miyake, and M.E. Fine, The Systems-Based Design of High-Strength, High-Conductivity Alloys, JOM, 1997, 49(3), p 56-6010.1007/BF02914659 ↗
5. R.L. Mehan, M.R. Jackson, J.R. Rairden, and W.T. Carter, The Use of a Ring Tensile Test to Evaluate Plasma Deposited Metals, J. Mater. Sci., 1987, 22, p 4476-448310.1007/BF01132050 ↗
6. C. Verdy, H. Liao, O. Landemarre, and C. Coddet, Development of a Low Cost System for the Cold Spray Process with Helium, Proceedings of the International Thermal Spray Conference 2008: Thermal Spray Crossing Borders, E. Lugscheider, Ed., DVS-Verlag, p 1302-130510.31399/asm.cp.itsc2008p1290 ↗
7. D. Hamana, M. Hachouf, L. Boumaza, and Z. El Abidine Biskri, Precipitation Kinetics and Mechanism in Cu-7 wt%Ag Alloy, Materials Sciences and Application, 2011, 2, p 899-91010.4236/msa.2011.27120 ↗
8. R. Wirth and H. Gleiter, Is Discontinuous (cellular) Precipitation an Effect of a Structural Transformation in the Migrating Phase Boundary?, Acta Metall., 1981, 29, p 1825-183010.1016/0001-6160(81)90108-5 ↗
9. W. Gust, J. Beuers, J. Steffen, S. Stiltz, and B. Predel, Diffusion Along Migrating and Stationary Grain Boundaries in the Cu-Ag System, Acta Metall., 1986, 34, p 1671-168010.1016/0001-6160(86)90113-6 ↗
10. D. Hamana and H. Choutri, Effect of Plastic Deformation on the Kinetics and Mechanism of Cellular Precipitation, Scripta Metall. Mater., 1991, 25, p 859-86410.1016/0956-716X(91)90238-V ↗
11. F. Gärtner, C. Borchers, T. Stoltenhoff, H. Kreye, and H. Assadi, Numerical and Microstructural Investigations of the Bonding Mechanisms in Cold Spraying, Thermal Spray 2003: Advancing the Science and Applying the Technology, C. Moreau and B. Marple, Ed., ASM International, Materials Park, OH, 2003, p 1-810.31399/asm.cp.itsc2003p0001 ↗
12. H. Fukanuma, N. Ohno, B. Sun, and R. Huang, In-flight partice velocity measurements with DPV-2000 in cold spray, Surf. Coat. Technol., 2006, 201, p 1935-194110.1016/j.surfcoat.2006.04.035 ↗
13. X.J. Ning, J.-H. Jang, and H.-J. Kim, The Effects of Powder Properties on In-Flight Particle Velocity and Deposition Process During Low Pressure Cold Spray Process, Appl. Surf. Sci., 2007, 253, p 7449-745510.1016/j.apsusc.2007.03.031 ↗
14. T. Schmidt, F. Gärtner, T. Stoltenhoff, H. Kreye, and H. Assadi, High Velocity Impact Phenomena and Coating Quality in Cold Spraying, Proceedings of the International Thermal Spray Conference 2005, Basel, Switzerland, 2005, E. Lugscheider, Ed., DVS-Verlag, p 232-23810.31399/asm.cp.itsc2005p0232 ↗
15. J. Karthikeyan, C.M. Kay, J. Lindeman, R.S. Lima, and C.C. Berndt, Cold spray processing of titanium powder, Proceedings of the International Thermal Spray Conference 2000: Surface Engineering Via Applied Research, C.C. Berndt, Ed., Pub. ASM international, Materials Park, OH, 2000, p 255-26210.31399/asm.cp.itsc2000p0255 ↗
16. C.-J. Li, W.-Y. Li, and H. Liao, Examination of the Critical Velocity for Deposition of Particles in Cold Spraying, J. Therm. Spray Technol., 2006, 15(2), p 212-22210.1361/105996306X108093 ↗
17. P. Coddet, C. Verdy, C. Coddet, F. Lecouturier, and F. Debray, Comparison of the Properties of Cold-Sprayed Cu-0.5Cr-0.05Zr Alloys After Various Heat Treatments Versus Forged and Vacuum Plasma Sprayed Alloys, J. Therm. Spray Technol., 2014, 23(3), p 486-49110.1007/s11666-013-0028-3 ↗
18. Y. Watanabe, Y. Ichikawa, I. Nonaka, and H. Miura, Characterization of Cold-Sprayed Copper Coatings with New Evaluation Parameter of EBSD Method, Proceedings of the International Thermal Spray Conference 2013: Innovative Coating Solutions for the Global Economy, R.S. Lima et al., Ed., p 132-13710.31399/asm.cp.itsc2013p0132 ↗
19. K. Ito and K. Ogawa, Effects of Spark-Plasma Sintering Treatment on Cold-Sprayed Copper Coatings, J. Therm. Spray Technol., 2014, 23(1-2), p 104-11310.1007/s11666-013-0047-0 ↗