Optimization of FDM printing parameters for high-speed fabrication of PLA-ABS Bi-layer laminate structures
Source abstract
Abstract
The present study investigates the influence of Fused Deposition Modelling (FDM) process parameters on the mechanical properties and surface quality of multi-material PLA-ABS Bi-layer Laminate Structures fabricated at elevated printing speeds. A Taguchi L9 orthogonal array was used to evaluate the effects of printing speed (150–250 mm/s), layer height (0.1–0.3 mm), and infill pattern (concentric, octagram spiral, and Hilbert curve) on tensile properties and surface roughness. The results show that a printing speed of 150 mm/s, a layer height of 0.1 mm, and concentric infill provided optimal mechanical performance, yielding a Young’s modulus of 1252.29 MPa, an ultimate tensile strength of 42.17 MPa, and an elongation at break of 5.79%. Surface roughness analysis indicated the minimum roughness (R a = 3.4 µm) at a printing speed of 250 mm/s and a layer height of 0.2 mm using concentric infill. Statistical evaluation using mean effect plots, signal-to-noise ratios, and ANOVA revealed that layer height predominantly governs surface quality, while infill pattern and printing speed significantly influence tensile behaviour. Optical fractography and scanning electron microscopy showed that fracture initiation occurred at interlayer interfaces and inter-raster voids. Well-bonded specimens exhibited ductile micro-void coalescence, whereas poorly bonded samples failed by interlayer separation and brittle fracture propagation. These findings demonstrate that appropriate selection of layer height and infill pattern enables rapid fabrication of PLA-ABS Bi-layer Laminate components with improved mechanical performance and surface finish.
Source: crossref · Quality: baseline
Research context
OpenAlex topics: Additive Manufacturing and 3D Printing Technologies · biodegradable polymer synthesis and properties · Cellular and Composite Structures
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
Affiliations
Thapar Institute of Engineering and Technology
References (68)
Show source-provided references
1. 10.3390/polym1407136710.3390/polym14071367 ↗
2. Patel S, Gupta S, Saket H, et al. Effect of infill pattern on the mechanical properties of PLA and ABS specimens prepared by FDM 3D printing. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering. 2024 Jun; 11: 09544089241258744. https://doi.org/10.1177/09544089241258744
3. 10.1007/s00170-023-11566-z10.1007/s00170-023-11566-z ↗
4. Hiremath S, Dsouza JF, Chiniwar DS, et al. Exploring the impact of epoxy coated 3D-printed polymers on surface roughness and mechanical behavior: an experimental and numerical study. Results in Engineering. Sep; 2024123: 102779. https://doi.org/10.1016/j.rineng.2024.102779
5. 10.3390/jcs605012110.3390/jcs6050121 ↗
6. Qayyum H, Saqib K, Hussain G, et al. Predicting flexural properties of 3D-printed composites: a small dataset analysis using multiple machine learning models. Elsevier. https://www.sciencedirect.com/science/article/pii/S2352492824031179 (accessed 6 March 2026).
7. 10.1016/j.jmapro.2024.09.09810.1016/j.jmapro.2024.09.098 ↗
8. Kamer MS, Temiz Ş, Yaykaşli H, et al. Comparison of mechanical properties of tensile test specimens produced with ABS and PLA material at different printing speeds in 3D printer. J Facult Eng Archit Gazi Univ 2022; 37: 1197–1211.
9. Sultana MN Sarker OS Dhar NR. Parametric optimization and sensitivity analysis of the integrated Taguchi-CRITIC-EDAS method to enhance the surface quality and tensile test behavior of 3D printed PLA and ABS parts. Heliyon. 2025 Jan 15;11(1). https://doi.org/10.1016/j.heliyon.2024.e4128910.1016/j.heliyon.2024.e41289 ↗
10. 10.1177/0892705725133924610.1177/08927057251339246 ↗
11. 10.1007/s00170-023-11435-910.1007/s00170-023-11435-9 ↗
12. Dairabayeva D Perveen A Talamona D. Tensile properties of the mono-material and multi-material PLA and ABS sandwich structures. In: 2024 15th international conference on mechanical and intelligent manufacturing technologies ICMIMT 2024 Cape town South Africa 17-19 May 2024. Institute of Electrical and Electronics Engineers Inc. 2024 pp. 168–172.10.1109/ICMIMT61937.2024.10585814 ↗
13. 10.1016/j.ijlmm.2020.03.00310.1016/j.ijlmm.2020.03.003 ↗
14. 10.1002/pc.2961710.1002/pc.29617 ↗
15. 10.1007/s40964-023-00411-010.1007/s40964-023-00411-0 ↗
16. 10.1007/s40430-024-05189-y10.1007/s40430-024-05189-y ↗
17. 10.1177/089270572199789210.1177/0892705721997892 ↗
18. 10.1007/s11340-018-00467-y10.1007/s11340-018-00467-y ↗
19. 10.1177/089270572199789210.1177/0892705721997892 ↗
20. 10.1177/089270572096456010.1177/0892705720964560 ↗
21. Sumalatha M, Supraja Reddy B, Chennaiah MB, et al. Experimental investigation on combined ABS and PLA materials using 3D printing FDM machine. In: Lecture Notes in Mechanical Engineering. Springer Science and Business Media Deutschland GmbH, 2024, pp. 371–382.
22. 10.1016/j.addma.2022.10307610.1016/j.addma.2022.103076 ↗
23. 10.1007/s40964-022-00295-610.1007/s40964-022-00295-6 ↗
24. 10.1002/pc.3007110.1002/pc.30071 ↗
25. 10.1007/s40032-022-00848-210.1007/s40032-022-00848-2 ↗
26. 10.1007/s40964-024-00575-310.1007/s40964-024-00575-3 ↗
27. 10.1080/2374068X.2021.191252710.1080/2374068X.2021.1912527 ↗
28. 10.1007/s00170-024-14232-010.1007/s00170-024-14232-0 ↗
29. 10.17977/um016v7i22023p09610.17977/um016v7i22023p096 ↗
30. 10.1002/pc.2693710.1002/pc.26937 ↗
31. Sudin MN, Shamsudin SA, Daud NM, et al. Examining the effect of annealing parameters on surface quality and tensile strength of ABS 3D-Printed materials. El-Cezeri Journal of Science and Engineering 2024; 11: 307–316.
32. 10.1038/s41598-025-13866-810.1038/s41598-025-13866-8 ↗
33. 10.1016/j.prostr.2021.12.01110.1016/j.prostr.2021.12.011 ↗
34. 10.3390/polym1318305710.3390/polym13183057 ↗
35. 10.1108/RPJ-07-2022-022110.1108/RPJ-07-2022-0221 ↗
36. 10.1007/s12206-021-0708-810.1007/s12206-021-0708-8 ↗
37. 10.1007/s11831-024-10220-510.1007/s11831-024-10220-5 ↗
38. Ekrem M Yilmaz M Bilgisi M et al. Yüksek hızlı 3B Yazıcıda basılmış PLA. PETG ve ABS Numunelerin Mekanik Özellikleri; 7: 2667–7989.
39. Chouhan V, Raj Singh RK, Mudgal D. Investigation of tensile properties of FDM-printed PLA-CF infill in PLA shell components. J Thermoplast Compos Mater. 2025 Dec 19; 08927057261421156. https://doi.org/10.1177/08927057261421156
40. 10.1007/s10965-025-04754-w10.1007/s10965-025-04754-w ↗
41. 10.1007/s00170-025-15478-y10.1007/s00170-025-15478-y ↗
42. Ayrilmis N Kariz M Šernek M et al. Effects of sandwich core structure and infill rate on mechanical properties of 3D-printed wood/PLA composites. https://doi.org/10.1007/s00170-021-07382-y/Published
43. 10.1080/15376494.2023.224494310.1080/15376494.2023.2244943 ↗
44. 10.1038/s41598-022-20782-810.1038/s41598-022-20782-8 ↗
45. 10.1007/s00170-021-08350-210.1007/s00170-021-08350-2 ↗
46. 10.1177/0731684425131497910.1177/07316844251314979 ↗
47. 10.1016/j.matpr.2022.05.42210.1016/j.matpr.2022.05.422 ↗
48. 10.1016/j.jcomc.2023.10039210.1016/j.jcomc.2023.100392 ↗
49. Gómez Amador AM Venturini Avendano RA González AQ et al. Mechanical characterization and testing of multi-polymer combinations in 3D printing. Heliyon. 2025 Feb 15;11(3). https://doi.org/10.1016/j.heliyon.2025.e4242010.1016/j.heliyon.2025.e42420 ↗
50. Yousefi KA Kennedy A. Experimental and numerical analysis of additively manufactured foamed sandwich beams. Compos Struct. 2023 May 15; 312:116866. https://doi.org/10.1016/j.compstruct.2023.11686610.1016/j.compstruct.2023.116866 ↗
51. 10.1080/10426914.2024.243775310.1080/10426914.2024.2437753 ↗
52. 10.1016/j.prostr.2024.01.03710.1016/j.prostr.2024.01.037 ↗
53. Bharat N Jain R Bose PSC. A comprehensive overview on additive manufacturing processes: materials applications and challenges. In: International conference on production and industrial engineering Jalandhar India 10-12 March 2023. Springer 2024 pp. 95–105.10.1007/978-981-99-6094-1_10 ↗
54. 10.1016/j.polymertesting.2020.10677010.1016/j.polymertesting.2020.106770 ↗
55. 10.1007/s40430-023-04199-610.1007/s40430-023-04199-6 ↗
56. 10.2478/bipcm-2022-002210.2478/bipcm-2022-0022 ↗
57. 10.1177/089270571987486010.1177/0892705719874860 ↗
58. 10.1002/app.5308910.1002/app.53089 ↗
59. 10.1007/s12206-023-2307-310.1007/s12206-023-2307-3 ↗
60. 10.1016/j.chaos.2025.11610710.1016/j.chaos.2025.116107 ↗
61. 10.1002/app.5033810.1002/app.50338 ↗
62. 10.1007/s40964-024-00767-x10.1007/s40964-024-00767-x ↗
63. 10.1007/s11665-024-10122-410.1007/s11665-024-10122-4 ↗
64. 10.1016/j.rinma.2022.10034810.1016/j.rinma.2022.100348 ↗
65. 10.1177/0892705723117079010.1177/08927057231170790 ↗
66. Moradi M, Hashemi R, Kasaeian-Naeini M. Experimental investigation of parameters in fused filament fabrication 3D printing process of ABS plus using response surface methodology. Int J Adv Manuf Technol. 2023 May; 1: 1–8. https://doi.org/10.1007/s00170-023-11468-0
67. 10.1007/s11665-022-07250-010.1007/s11665-022-07250-0 ↗
68. Morales MA Porras J Maranon A et al. Effect of polypropylene-grafted-maleic anhydride and rice husk particle size on 3D-Printing filament composites from recycled polypropylene. Polym Compos. 2025 Nov 10;46(16):15125-41. https://doi.org/10.1002/pc.3011810.1002/pc.30118 ↗