journal article·1997-05

Experimental Analysis and Process Window Development for Continuous Filament-Wound APC-2

D. L. James, W. Z. Black

Publisher page

Abstract

A small-scale filament winding apparatus was built so that surface temperature distributions could be determined during actual filament winding runs and the resulting temperatures could be compared to those predicted by a numerical model. Several experimental runs were performed using various combinations of infrared energy input and prepreg tape velocities. Infrared thermography was used to determine the surface temperature of the composite during each experiment. The field of view of the infrared camera included approximately 90 degrees of the mandrel in the angular direction and two-thirds of the axial length of the composite on the mandrel. The numerical and experimental results in this paper suggest that varying the position of the infrared lamp, changing the prepreg tape velocity (winding speed), or the heat flux incident on the composite have a major impact on the temperature distribution throughout the composite; these factors may therefore be used to alter the physical properties and overall quality of a filament-wound part. Improved consolidation will likely occur if a low-power infrared lamp is used to preheat the prepreg tape prior to contact with the mandrel and another infrared preheater is focused on the mandrel at an angular location prior to the tape-mandrel interface. The majority of the composite heating should be achieved by a high-power lamp located such that the energy is focused on the mandrel in the vicinity of the prepreg tape-mandrel interface but displaced in the direction opposite the axial velocity of the tape. Therefore, the location of the lamp must move relative to the tape when the crosshead feed mechanism changes directions. By displacing the axial location of the lamp slightly downstream (in the direction of motion of the crosshead feed mechanism) of the tape-mandrel interface, preheating of the composite on the mandrel occurs prior to the tape being laid on the mandrel. The numerical model is used to identify processing windows that lead to a wellconsolidated part. The processing window is defined by upper temperature limits that will damage the part and lower temperature limits that will leave the part unconsolidated. The temperature limits are selected from a knowledge of the autohesive characteristics of APC-2 (complete intimate contact and void-free prepreg tape are assumed). The model is then used to identify winding conditions such as infrared energy input, winding speed, and composite substrate thickness that result in a consolidated product.
Source: crossref · Quality: baseline

Research context

OpenAlex topics: Electronic Packaging and Soldering Technologies · 3D IC and TSV technologies · Engineering Applied Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

Affiliations

Texas Tech University, Dept. of Mechanical Engineering, Box 41021, Lubbock, TX 79409-1021

School of Mechanical Engineering, Georgia Institute of Technology, Atlanta, GA 30332-0405

References (25)

Show source-provided references
1. 10.1177/08927057920050020310.1177/089270579200500203 ↗
2. Agarwal, V. 1991. "The Role of Molecular Mobility in the Consolidation and Bonding of Thermoplastic Composite Materials, Ph.D. dissertation, University of Delaware, (August):123-129.
3. 10.1177/00219983900240020210.1177/002199839002400202 ↗
4. Argus International
5. 10.1115/1.325050210.1115/1.3250502 ↗
6. 10.1177/08927057880010010910.1177/089270578800100109 ↗
7. Brage, A. · SAMPE Quarterly · 1988 · 19 · 31
8. 10.1016/0032-3861(83)90144-110.1016/0032-3861(83)90144-1 ↗
9. Carpenter, C. 1992. On-Line Consolidation Mechanisms for Thermoplastic Composites, Master's thesis, Department of Mechanical Engineering, Georgia Institute of Technology, (May).
10. Dara, P H. and A. C. Loos. 1985. "Thermoplastic Matrix Composite Processing Model," CCMS Report 85-10, Center for Composite Materials and Structures, Virginia Polytechnic Institute, pp. 5-52, (Sept.).
11. 10.1016/0010-4361(88)90124-310.1016/0010-4361(88)90124-3 ↗
12. Heng, S. F. 1988. Experimental and Theoretical Thermal Analysis of Microelectronic Devices, Ph.D. dissertation, School of Mechanical Engineering, Georgia Institute of Technology, pp. 164-170.
13. Inframetrics Instruction Manual · 1981
14. James, D. L. 1992. 77Termnal Analysis of the Continuous Filament Winding Process, Ph.D. dissertation, School of Mechanical Engineering, Georgia Institute of Technology.
15. 10.1177/08927057960090010510.1177/089270579600900105 ↗
16. Krempel, L. A. 1988. Experimental Temperature Measurements of Microelectronic Computer Boards Using an lml-aretl Camnera, Master's thesis, School of Mechanical Engineering, Georgia Institute of Technology, pp. 46-58.
17. Leach, D. 1991. An E&perimental Study of the Processing Parameters in Thermoplastic Filament Winding, Master's thesis, School of Mechanical Engineering, Georgia Institute of Technology, (August).
18. Muzzy, J. D. · 1
19. 10.1177/08927057910040010210.1177/089270579100400102 ↗
20. 10.1115/1.291056210.1115/1.2910562 ↗
21. Pitchumani, R. · 223
22. Pitchumani, R. · 71
23. Springer, G. S. · 661
24. Thammongkol, V. 1989. Electrostatic Fluidized Bed Prepregging of Carbon Fiber wt ith PEEK, M.S. thesis, Dept. of Chemical Engineering, Georgia Institute of Technology, (March).
25. Warner Electric