journal article·2017-08

Comparative assessment of support plates’ influences on delamination damage in micro-drilling of CFRP laminates

A. Dogrusadik, A. Kentli

Publisher page

Abstract

Abstract In this study, drilling induced delamination damage which occurs during micro-drilling of CFRP laminates was investigated experimentally under variable cutting speeds and feed rates. Unlike the previous studies, the delamination factors in micro-drilling of CFRP laminates were precisely calculated and compared for supported and unsupported cases. Using support plates which are placed front and rear sides of the CFRP laminate is one of the methods which limits the delamination damage. Two different setups of support plates were used in the experiments. In the first setup, the entry board was aluminum plate and the backing board was phenolic plate. In the second setup, the entry board was brass plate and the backing board was wooden plate. Hole pictures were taken from each CFRP laminate by using a digital microscope. The first, the middle and the last three holes were inspected from the front and rear sides of the CFRP laminate. Minitab was used to evaluate the experiments’ outputs, and response surface method was used to optimize the process parameters. It has been revealed that the delamination damage in micro-drilling differs from the delamination damage in conventional drilling of CFRP laminates. Obviously, the process exhibits unusual delamination behavior as process size decreases.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Advanced machining processes and optimization · Advanced Machining and Optimization Techniques · Advanced Surface Polishing Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (23)

Show source-provided references
1. Identification and control for micro-drilling productivity enhancement10.1016/S0890-6955(99)00019-X ↗
2. Size effect of depth of cut on chip formation mechanism in machining of CFRP10.1016/j.compstruct.2016.11.044 ↗
3. A review of mechanical drilling for composite laminates10.1016/j.compstruct.2011.11.024 ↗
4. The path towards delamination-free drilling of composite materials10.1016/j.jmatprotec.2005.06.039 ↗
5. Drill geometry and operating effects when cutting small diameter holes in CFRP10.1016/j.ijmachtools.2009.05.009 ↗
6. Numerical investigation of the effects of drill geometry on drilling induced delamination of carbon fiber reinforced composites10.1016/j.compstruct.2013.04.026 ↗
7. Effects of special drill bits on drilling-induced delamination of composite materials10.1016/j.ijmachtools.2005.10.004 ↗
8. The effect of chisel length and associated pilot hole on delamination when drilling composite materials10.1016/S0890-6955(03)00127-5 ↗
9. Workpiece damping and its effect on delamination damage in drilling thin composite laminates10.1016/S0924-0136(03)00812-4 ↗
10. Micro-drilling of CFRP plates using a high-speed spindle10.4028/www.scientific.net/KEM.523-524.1035 ↗
11. Characteristics of chip formation in the micro-drilling of multi-material sheets10.1016/j.ijmachtools.2011.08.017 ↗
12. Investigation of micro-cutting operations10.1016/j.ijmachtools.2005.05.015 ↗
13. Chatter stability of metal cutting and grinding10.1016/S0007-8506(07)60032-8 ↗
14. Analyses of forces and hole quality in micro-drilling of carbon fabric laminate composites10.1177/0021998312445594 ↗
15. Size effects in micro drilling of carbon fiber reinforced plastic composite10.1007/s11740-014-0526-2 ↗
16. Some experimental investigations in the drilling of carbon fiber-reinforced plastic (CFRP) composite laminates10.1016/S0890-6955(96)00095-8 ↗
17. A novel approach based on digital image analysis to evaluate the delamination factor after drilling composite laminates10.1016/j.compscitech.2006.10.009 ↗
18. Cutting edge rounding: an innovative tool wear criterion in drilling CFRP composite laminates10.1016/j.ijmachtools.2009.08.002 ↗
19. Measuring delamination in carbon/epoxy composites using a shadow moire laser based imaging technique10.1016/j.compstruct.2005.11.039 ↗
20. Utilizing internal icing force to reduce delamination in drilling composite tubes10.1016/j.compstruct.2015.11.043 ↗
21. Development of a micro-drilling burr-control chart for PCB drilling10.1016/j.precisioneng.2013.07.010 ↗
22. An investigation of burrs, chip formation, hole size, circularity and delamination during drilling operation of GLARE using ANOVA10.1016/j.compstruct.2016.10.015 ↗
23. Recent advances in drilling FRP/Ti composite: a state-of-the-art review10.1016/j.compstruct.2015.09.028 ↗