journal article·2011-09

Creep behavior of pultruded GFRP elements – Part 1: Literature review and experimental study

Mário F. Sá, Augusto M. Gomes, João R. Correia, Nuno Silvestre

Composite Structures· Volume 93· Issue 10
Publisher page

Abstract

Abstract This paper first presents a state-of-the-art review about the viscoelastic time-dependent – creep behavior of fibre reinforced polymer (FRP) materials in general, and pultruded glass fibre reinforced polymers (GFRPs) in particular, at different element scales. The literature review aims at pointing out the present gaps regarding the understanding of this phenomenon and guiding the future developments lines for the application of pultruded GFRP in civil infrastructure, including bridges and buildings. The paper then presents results of experimental investigations carried out on pultruded GFRP material made of polyester and E-glass fibres at two different scales: (i) laminate and (ii) full-scale profile. The test programme included (i) flexural creep tests on 8 mm thick small-scale specimens with a span of 160 mm, subjected to sustained loads corresponding to stress levels ranging from 20% to 80% of their ultimate stress; and (ii) a flexural creep test on an I-profile (150 × 75 × 8 mm) with a span of 1800 mm, subjected to a constant load of 1/3 of its ultimate load. The deflections and axial strains over time, measured in laboratory environmental conditions, were recorded for time durations up to 1600 h. The results obtained confirm an important effect of the creep phenomenon on pultruded GFRP profiles, with small-scale specimens having failed for load levels as low as 50% of the ultimate stress; in addition, the creepocity measured on both types of elements was quite significant after the first hours, even for an average load level of 30%. Subsequently, the experimental results were used for material characterisation by means of empirical and phenomenological formulations (Part 2).
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Structural Behavior of Reinforced Concrete · Concrete Corrosion and Durability · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (36)

Show source-provided references
1. Bank · 2006
2. Keller T. Use of fibre reinforced polymers in bridge construction. In: Structural Engineering Documents, vol. 7. IABSE, Zurich; 2003.10.2749/sed007 ↗
3. Creep behavior of FRP composites: a review of technical literature10.1177/073168449501400603 ↗
4. Sá MF. Mechanical and structural behavior of FRP – Pultruded GFRP elements. Master’s Thesis in Structural Engineering. IST, Technical University of Lisbon; 2007 [in Portuguese].
5. Correia JR. GFRP pultruded profiles in Civil Engineering: hybrid solutions, bonded connections and fire behavior. Ph.D. Thesis in Civil Engineering. IST, Technical University of Lisbon; 2008.
6. Guedes RM. Life prediction of materials polymer matrix composites. Ph.D. Thesis in Mechanical Engineering. FEUP, University of Porto; 1997 [in Portuguese].
7. Daniali S. Short-term and long-term behavior of two types of reinforced plastic beams. In 46th Annual Conference, Composites Institute; February 1991: 13-A-1-5.
8. Creep and failure of a full-size fibre reinforced plastic pultruded frame10.1016/0961-9526(92)90005-Q ↗
9. 26-year creep and recovery of poly (vinyl chloride) and polyethylene10.1002/pen.760270809 ↗
10. Short- and long-term structural properties of pultruded beam assemblies fabricated using adhesive bonding10.1016/0263-8223(93)90186-T ↗
11. Effect of hybridization on the creep and stress relaxation characteristics of pultruded composites10.1177/073168449801700303 ↗
12. Viscoelastic creep characteristics of neat thermosets and thermosets reinforced with E-glass10.1520/CTR10500J ↗
13. Flexural creep properties of E-glass reinforced polymers10.1016/j.compstruct.2003.09.022 ↗
14. Deflection creep of pultruded composite sheet piling10.1061/(ASCE)1090-0268(2004)8:5(471) ↗
15. Spence BR. Compressive viscoelastic effects (creep) of a unidirectional glass/epoxy composite material. In 35th international SAMPE symposium; April 1990. p. 1490–3.
16. Compression creep of pultruded E-glass reinforced plastic angles10.1061/(ASCE)0899-1561(1995)7:4(269) ↗
17. Compression creep of a pultruded e-glass/vinylester composite10.1016/S0266-3538(98)00009-8 ↗
18. Creep rupture of a GFRP composite at elevated temperatures10.1016/S0045-7949(99)00176-5 ↗
19. Time-dependent deformation of pultruded fibre-reinforced polymer composite columns10.1061/(ASCE)1090-0268(2003)7:4(356) ↗
20. Bennet EA. Influence of creep on the stability of pultruded E-glass/polyester composite columns at elevated service temperatures. MSc Thesis in Civil Engineering. School of Civil Engineering, Georgia Institute of Technology, Atlanta, GA; 2005.
21. Smith KJ. Compression creep of a pultruded E-glass/polyester composite at elevated service temperatures. MSc Thesis in Civil Engineering. School of Civil Engineering, Georgia Institute of Technology, Atlanta, GA; 2005.
22. Compression creep rupture behavior of a glass/vinyl ester composite laminate subject to fire loading conditions10.1016/j.compscitech.2007.04.009 ↗
23. ISO 527. Determination of tensile properties. Part 1: general principles. International Standards Organization, Genève; 1993.
24. ISO 527. Determination of tensile properties. Part 4: Test conditions for isotropic and orthotropic fibre-reinforced plastic composites. International Standards Organization, Genève; 1997.
25. ISO 14125. Fibre-reinforced plastic composites. Determination of flexural properties. International Standards Organization, Genève; 1998.
26. ASTM D695. Standard test method for compressive properties of rigid plastics. American Society for Testing and Materials, West Conshohocken, PA; 2002.
27. ASTM D2344. Standard test method for short-beam strength of polymer matrix composite materials and their laminates. West Conshohocken, PA: American Society for Testing and Materials; 2000.
28. ISO 1172. Textile–glass-reinforced plastics – Prepregs, moulding compounds and laminates – Determination of the textile–glass and mineral filler content – Calcination methods. International Standards Organization, Genève; 1996.
29. Jones · 1999
30. Experimental and theoretical study of the creep behavior of GFRP-reinforced polymer concrete10.1016/j.compscitech.2003.10.004 ↗
31. ISO 899-2. Determination of creep behavior. Part 2: Flexural creep by 3-PB. International Standards Organization, Genève; 2003.
32. CEN. EN 13706. Reinforced plastics composites – Specifications for pultruded profiles. Part 1: designations; Part 2: methods of test and general requirements; Part 3: specific requirements. Brussels: European Committee for Standardisation; 2002.
33. Correia JR, Branco FA, Silva N, Camotim D, Silvestre N. First-order, buckling and post-buckling behavior of GFRP pultruded beams – Part 1: experimental Study. Comput Struct (Provisionally accepted).
34. Silva N, Camotim D, Silvestre N, Correia JR, Branco FA. First-order, buckling and post-buckling behavior of gfrp pultruded beams – Part 2: numerical Study. Comput Struct (Provisionally accepted).
35. Flexural and shear moduli of full-section fibre reinforced plastic (FRP) pultruded beams10.1520/JTE11531J ↗
36. Sá MF, Gomes AM, Correia JR, Silvestre NP. Creep behavior of pultruded GFRP elements – Part 2: analytical study. Compos Struct (Accepted for publication).