journal article·2014-12Open access

The temperature behaviour inside the mat of wood-based panel during hot pressing under various manufacturing conditions

Muhammad Navis Rofii, Noriko Yamamoto, Sachio Ueda, Yoichi Kojima, Shigehiko Suzuki

Journal of Wood Science· Volume 60· Issue 6

Abstract

This study focused on the heat transfer involved in hot pressing. The temperature behaviour inside the mat of wood-based panels according to the manufacturing conditions—such as mat moisture level, furnish material, and press temperature—was characterised. Hinoki strands and ring-flaker recycled wood particles were used for experimental panel production. Temperature behaviour was measured at the surface and the centre of the mat. The results indicate that the manufacturing condition affected the temperature behaviour of the mat during hot pressing. Plateau time increased with increasing mat moisture content and utilisation of hinoki strands but decreased with increasing press temperature. Use of hinoki strands resulted in a higher plateau temperature than did recycled wood particles. The higher mat moisture content and press temperature resulted in a higher plateau temperature. Furnish type also affected heat conductivity in the mat centre after the completion of the plateau.
Source: europepmc · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Wood Treatment and Properties · Textile materials and evaluations

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (18)

Show source-provided references
1. Kamke FA (2004) Physic of hot pressing. In: Proceedings of Fundamentals of Composite Processing. General Technical Report. FPL-149. USDA Forest Service, Forest Products Laboratory, Madison, pp 3–18
2. Kavazovic Z, Deteix J, Cloutier A, Fortin A (2010) Sensitivity study of a numerical model of heat and mass transfer involved during the medium-density fibreboard hot pressing process. Wood Fiber Sci 42:130–149
3. Zombori BG, Kamke FA, Watson LT (2003) Simulation of the internal conditions during the hot-pressing process. Wood Fiber Sci 35:2–23
4. Cai Z, Birkeland M, Wescott JM, O’Dell J, Winandy JE (2009) Effects of press size on internal steam pressure during particleboard hot-pressing process. Forest Prod J 59:40–4410.13073/0015-7473-59.10.40 ↗
5. Wong ED, Zhang M, Wang Q, Kawai S (1998) Effects of mat moisture content and press closing speed on the formation of density profile and properties of particleboard. J Wood Sci 44:287–29510.1007/BF00581309 ↗
6. Kamke FA, Casey LJ (1988) Fundamentals of flakeboard manufacture: internal-mat conditions. Forest Prod J 38:38–44
7. Cai Z, Muehl JH, Winandy JE (2006) Effects of panel density and mat moisture content on processing medium density fibreboard. Forest Prod J 56:20–25
8. Kelly MW (1977) Critical literature review of relationships between processing parameters and physical properties of particleboard. USDA General Technical Report of the Forest Products Laboratory, Madison, pp 36–44
9. Dai C, Wang S (2004) Press control for optimized wood composite processing and properties Part 1: pressing variables and sensors. In: Proceedings of Fundamental of Composite Processing. General Technical Report. FPL-149. USDA Forest Service, Forest Products Laboratory, Madison, pp 54–64
10. Korai H, Ling N, Osada T, Yasuda O, Sumida A (2011) Development of air-injection press for preventing blowout of particleboard I: effects of an air-injection press on board properties. J Wood Sci 57:401–40710.1007/s10086-011-1191-0 ↗
11. Korai H, Saotome H (2013) Blowout conditions and properties of isocyanate resin bonded particleboard manufactured from high-moisture particles using an air-injection press. J Wood Sci 59:42–4910.1007/s10086-012-1298-y ↗
12. Bolton AJ, Humphrey PE, Kavrouras PK (1989) The hot pressing of dry-formed wood-based composites Part III: predicted vapour pressure and temperature variation with time, compared with experimental data for laboratory boards. Holzforschung 43:265–27410.1515/hfsg.1989.43.4.265 ↗
13. Garcia PJ, Avramidis S, Lam F (2001) Internal temperature and pressure responses to flake alignment during hot-pressing. Holz Roh Werkst 59:272–27510.1007/s001070100218 ↗
14. Wu J, Yu Z, Chen T (2006) Heat-transfer process during hot-pressing of flakeboard. Front For China 3:343–34710.1007/s11461-006-0007-7 ↗
15. Miyamoto K, Nakahara S, Suzuki S (2002) Effect of particle shape on linear expansion of particleboard. J Wood Sci 48:185–19010.1007/BF00771365 ↗
16. Hata T, Subiyanto B, Kawai S, Sasaki H (1989) Production of particleboard with steam-injection Part 1: temperature behaviour in particle mat during hot-pressing and steam-injection pressing. Wood Sci Tech 23:361–36910.1007/BF00353252 ↗
17. Dai C, Wasylciw W, Jin J (2004) Comparison of the pressing behaviour of wood particleboard and strawboard. Wood Sci Tech 38:529–53710.1007/s00226-004-0256-2 ↗
18. Sanjari E (2013) A new method for accurate calculation of saturated vapour pressure. Thermochim Acta 560:12–1610.1016/j.tca.2013.03.002 ↗