SURFACE FINISH AND TOOL WEAR CHARACTERIZATION IN HARD TURNING USING A MATHEMATICAL CUTTING TOOL REPRESENTATION
Source abstract
Abstract
Abstract The development of a general 3D model for a corner-radiused, chamfered, edge-honed cutting worn tool is elaborated. The surface of the cutting tool was constructed using one angular scalar specifying location on the corner radius and leading/trailing edges and another non-dimensional scalar for specifying location on the relief, edge-hone, chamfer and tool-top. Then, for given geometric parameters and cutting conditions, the angular extremities of contact on the corner radius and leading/trailing edges was obtained and validated. The kinematic surface finish on the workpiece surface including the Brammertz and sideflow effects was then simulated in typical hard turning. The model was expanded to allow wiper edges and flank wear. A simplified crater wear model was adopted for continuous hard turning to allow virtual cross-sectioning. Accurate estimation of flank and crater wear volume was also enabled. The model results for the fresh tool agreed with well-known trends from 2D modeling. Preliminary results indicate that there exists a geometric basis for higher Ra and Rt for a worn tool. The Brammertz effect simulation, though not in agreement with the data of Knuefermann (Citation2003) corroborated the modification proposed therein. Keywords: edge honekinematichard turningsurface finishtool wear ACKNOWLEDGMENTS The author acknowledges the advice and guidance of his doctoral thesis advisor Prof. William Endres of Michigan Technological University and Gustavo Delfino, a former graduate student, whose term paper at University of Michigan provided the starting point and motivation for this work. Notes 1Mathematica is the registered trademark of Wolfram Research, Inc. The author presented an outline of the work in a recent conference (Kountanya, R., Citation2011. A Computer Model For Worn Cutting Edge In Hard Turning, Intertech 2011, Chicago, IL.). 2Wyko is the registered trademark of Veeco Instruments Inc. *Note: Currently with United Technologies Research Center, Process Modeler.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Advanced machining processes and optimization · Metal Alloys Wear and Properties · Advanced Surface Polishing Techniques
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. Brammertz P. · Industrie-Anzeiger · 1961 · 83 · 25
2. Chen , S. ; Jawahir , I. ( 2008 ) The influence of cutting edge radius on surface integrity and size effects in dry turning of automotive aluminum alloy A356 with diamond tools. Proceedings of the 11th CIRP Conference on Modelling of Machining Operations, Gaithersburg, MD, 16–17 September 2008, pp. 247–254 .
3. 10.1016/j.cirpj.2008.09.00110.1016/j.cirpj.2008.09.001 ↗
4. 10.1016/j.cirp.2008.03.12110.1016/j.cirp.2008.03.121 ↗
5. Danzl , R. ; Helmli , F. ; Scherer , S. ( 2009 ) Focus variation–a new technology for high resolution optical 3d surface metrology,Application of Contemporary Non-Destructive Testing in Engineering, The 10th International Conference of the Slovenian Society for Non-Destructive Testing, Ljubljana, Slovenia, 1–3 September 2009, pp. 484–491 .
6. 10.1016/j.ijmachtools.2004.08.02210.1016/j.ijmachtools.2004.08.022 ↗
7. 10.1016/S0043-1648(03)00384-310.1016/S0043-1648(03)00384-3 ↗
8. Doyle , J.A. ( 2009 ) Analysis and comparison of metrology methods for quantifying micro-endmills.Mechanical Engineering, Massachussetts Institute of Technology, Cambridge, MA, p. 65 .
9. 10.1016/S0007-8506(07)60372-210.1016/S0007-8506(07)60372-2 ↗
10. Knuefermann , M.M.W. ( 2003 ) Machining surfaces of optical quality by hard turning, School of Applied Sciences, Cranfield University, Cranfield, Bedfordshire, UK .
11. 10.1016/S0007-8506(07)60654-410.1016/S0007-8506(07)60654-4 ↗
12. Knuefermann M.M.W. · Industrial Diamond Review · 2001 · 2 · 87
13. 10.1243/09544054JEM104210.1243/09544054JEM1042 ↗
14. Kountanya R. · 2011
15. 10.1016/j.jmatprotec.2009.02.01110.1016/j.jmatprotec.2009.02.011 ↗
16. 10.1016/j.wear.2005.02.05610.1016/j.wear.2005.02.056 ↗
17. 10.1016/0020-7357(66)90021-710.1016/0020-7357(66)90021-7 ↗
18. 10.1016/S1526-6125(07)70107-X10.1016/S1526-6125(07)70107-X ↗
19. Shaw M.C. · 1996
20. Sood , R. ; Guo , C. ; Malkin , S. ( 1999 ) Turning of hardened steel, 3rd International Machining and Grinding: ‘Turning of Hardened Steel'. SME, Dearborn, MI, USA, Cincinnati, OH, USA Oct 4–Oct 7 1999, pp. 1–12 .
21. 10.1016/0020-7357(67)90008-X10.1016/0020-7357(67)90008-X ↗