journal article·2000-01

THE EFFECT OF ZERO-CLEARANCE LANDS IN ORTHOGONAL MACHINING IN LIGHT OF AN INTERNALLY CONSISTENT MATERIAL MODEL

Roy J. Schimmel, William J. Endres, Robin Stevenson

Publisher page

Abstract

Abstract It is well known that the edge geometry of a cutting tool affects the forces measured during metal cutting. Two experimental methods have been suggested in the past to extract the ploughing (non-cutting) component from the (total) measured force: (1) an extrapolation approach; and (2) a dwell force technique. However, it has been shown that no ploughing (non-cutting, parasitic) components need be considered to analyze the cutting forces obtained using tools with a honed (radiused) edge and positive clearance. This study reports the influence of varying lengths of zero-clearance flank in combination with controlled edge radii. Analysis shows that zero-clearance flanks do introduce ploughing (non-cutting, parasitic) force components and that the magnitude of the parasitic force is a function of the length of the land. If these parasitic components are subtracted from the total forces, the analysis described by Schimmel et al. (I) may then be followed, effectively reducing the analysis to consideration of the hone alone. Thus, the effect of a zero-clearance land is strictly parasitic and does not affect the chip formation mechanisms. It was also noted that, in these tests, Coulomb's Law applies at the land-workpiece interface and that the coefficient of friction is independent of edge radius and rake angle.
Source: openalex_inverted_index · Quality: baseline

Research context

OpenAlex topics: Advanced machining processes and optimization · Tunneling and Rock Mechanics · Advanced Machining and Optimization Techniques

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (16)

Show source-provided references
1. Schimmel R. · ASME J. Mfg. Sci. Engg. · 1999
2. 10.1016/0890-6955(88)90021-110.1016/0890-6955(88)90021-1 ↗
3. Okushima K. · Bull, of the Japan Soc. Prec. Engg. · 1963 · 1
4. Kobayashi S. · ASME J. Engg. for Industry · 1960 · 82 · 32410.1115/1.3664240 ↗
5. Thomson E. G. · ASME J. Engg. for Industry · 1962 · 5310.1115/1.3667438 ↗
6. Coulomb C. A. · Memoires de Mathematique et du Physique de VAcademie Roy ale des Science. · 1785
7. Zorev , N. N. , 1966 , “ Metal Cutting Mechanics, ” Pergamon Press, Oxford , (Translated by H. S. H. Massey ).
8. 10.1016/0043-1648(75)90161-110.1016/0043-1648(75)90161-1 ↗
9. Palmer W. B. · 173 · 623
10. 10.1243/JMES_JOUR_1972_014_015_0210.1243/JMES_JOUR_1972_014_015_02 ↗
11. McAdams H. T. · ASME J. Engg. for Industry · 1961 · 50510.1115/1.3664580 ↗
12. 10.1115/1.343908110.1115/1.3439081 ↗
13. Schimmel R. J. · Proc. ASME IMECE · 1997 · 261
14. Oxley , P. L. B. , 1989 , The Mechanics of Machining: An Analytical Approach to Assessing Machinability, Ellis Horwood Limited, Chichester .
15. 10.1016/S0890-6955(97)00022-910.1016/S0890-6955(97)00022-9 ↗
16. Amontons G. · Memoires Academic Royale Science · 1699