Hardened behavior of mortar based on recycled aggregate: Influence of saturation state at macro- and microscopic scales
Source abstract
Abstract
Abstract The influence of saturation state of recycled concrete aggregate (RCA) on the hardened behavior of mortar was investigated at macroscopic and microscopic scales. At the macroscopic scale, a good adhesion between the RCA and the new cement matrix at 28 days of hydration is observed. However due to its intrinsic strength; a limiting effect of the RCA is found in comparison to natural aggregates (NA). This effect limits the strength of mortars for small values of effective water to cement ratio. In parallel, a low influence of moisture condition of used RCA on the mechanical properties is observed. The microstructure of interfacial transition zone (ITZ) is characterized by image analysis of backscatter scanning electron microscopy (SEM) images at 2 and 28 days of hydration and nano-indentation test under SEM at 28 days of hydration. For mortars based on RCA, the average porosities in the ITZ of mortars with dried and over-saturated aggregates are identical. But the saturation state of aggregates has a significant influence on the distribution of porosity in the ITZ. The porosity in the ITZ of mortars containing RCA is larger than that of mortars made with NA. This difference can be explained by a higher effective water to cement ratio in the mortar based on RCA. This excess may be due to a lower value of absorption of RCA than that provided by the absorption estimated on RCA. The nano-indentation test under the SEM shows that the initial saturation state of recycled sand (dry or over-saturated) does not influence the micro-hardness of the new cement matrix.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Recycled Aggregate Concrete Performance · Innovative concrete reinforcement materials · Concrete and Cement Materials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (36)
Show source-provided references
1. Life Cycle Assessment guidelines for the sustainable production and recycling of aggregates: the Sustainable Aggregates Resource Management project (SARMa)10.1016/j.jclepro.2012.01.020 ↗
2. Characterisation of interfacial microstructure
3. Interfacial transition zone in concrete10.1016/1065-7355(95)90037-3 ↗
4. Computer Modelling of Interfacial Transition Zone: Microstructure and Properties
5. The interfacial transition zone (ITZ) between cement paste and aggregate10.1023/B:INTS.0000042339.92990.4c ↗
6. Experimental study on interfacial strength of the high performance recycled aggregate concrete
7. An overview of study on recycled aggregate concrete in China (1996–2011)10.1016/j.conbuildmat.2011.12.074 ↗
8. Recycled concrete a source for new aggregate10.1520/CCA10349J ↗
9. Microstructural analysis of recycled aggregate concrete produced from two-stage mixing approach10.1016/j.cemconres.2004.10.025 ↗
10. Microstructure analysis of hardened recycled aggregate concrete10.1680/macr.2006.58.10.683 ↗
11. Study on interfacial transition zone properties of recycled aggregate by micro-hardness test10.1016/j.conbuildmat.2012.09.114 ↗
12. The influence of aggregate on the compressive strength of normal- and high-strength concrete
13. The effect of limestone aggregate porosity and saturation degree on the interfacial zone
14. Influence of fine recycled concrete aggregates on the properties of mortars10.1016/j.conbuildmat.2015.02.037 ↗
15. Dao · 2012
16. Recybéton, Projet National Recybéton, http://www.pnrecybeton.fr/, 2012.
17. EN 196-1 · 2006
18. Influence of hardened cement paste content on the water absorption of fine recycled concrete aggregates
19. Fresh behavior of mortar based on recycled sand – influence of moisture condition10.1016/j.conbuildmat.2015.12.071 ↗
20. NF EN 413-2 · 2006
21. Comparison of methods for arresting hydration of cement10.1016/j.cemconres.2011.06.003 ↗
22. Microstructural Gradients in Cement Paste around Aggregate Particles10.1557/PROC-114-77 ↗
23. Considerations in image analysis as applied to investigations of the ITZ in concrete10.1016/S0958-9465(00)00085-8 ↗
24. Influence of coarse aggregate on the permeation, durability and the microstructure characteristics of ordinary Portland cement concrete10.1016/j.conbuildmat.2005.02.022 ↗
25. Influence of aggregate size, water cement ratio and age on the microstructure of the interfacial transition zone10.1016/S0008-8846(03)00205-9 ↗
26. Hemavibool · 2007
27. Automated identification of the aggregate–paste interfacial transition zone in mortars of silica sand with Portland or alkali-activated slag cement paste10.1016/S0008-8846(00)00254-4 ↗
28. Pore segmentation of cement-based materials from backscattered electron images10.1016/j.cemconres.2005.10.006 ↗
29. Delesse · Ann. Mines · 1848 · 13 · 379
30. Overestimation of the interface thickness around convex-shaped grain by sectional analysis10.1016/j.actamat.2007.03.009 ↗
31. Characterising aggregate surface geometry in thin-sections of mortar and concrete10.1016/j.cemconres.2008.04.004 ↗
32. Determining the water absorption of recycled aggregates utilizing hydrostatic weighing approach10.1016/j.conbuildmat.2011.08.018 ↗
33. Combined experimental methods to assess absorption rate of natural and recycled aggregates
34. The contact zone between Portland cement paste and glass ‘aggregate’ surfaces10.1016/0008-8846(78)90012-1 ↗
35. Backscattered electron imaging of cementitious microstructures: understanding and quantification10.1016/j.cemconcomp.2004.02.029 ↗
36. Saporta · 1990