journal article·2018-10Open access

Lightweight hybrid organic-inorganic geopolymers obtained using polyurethane waste

L. Bergamonti, R. Taurino, L. Cattani, D. Ferretti, F. Bondioli

Abstract

Abstract Lightweight geopolymers from wastes with reduced thermal conductivity have become an important trend for green buildings sector. In this work, organic-inorganic hybrid geopolymers were prepared from polyurethane powders wastes (polyurethane foam and polyisocianurate foam). Chemical, physical and mechanical properties of geopolymers, manufactured with different percentages of polyurethane wastes are reported and discussed. The FTIR spectroscopy allowed to verify the influence of both polyurethane powders on the framework structure revealing H-bonds between polyurethane and inorganic phase. Flexural and compressive strengths showed that content and typology of the used polyurethane wastes affected the material behavior. The strength of hybrid geopolymers was maximized with polyisocianurate foam waste addition in a concentration lower than 14% in weight. Thermal conductivity was carried out on appropriate samples, showing that the hybrid geopolymers exhibit satisfactory isolation properties. The new materials proposed in this work represents an innovative solution, enhancing the thermal resistance of the buildings by using a waste intended for landfill.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Microbial Applications in Construction Materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (59)

Show source-provided references
1. Methods for polyurethane and polyurethane composites, recycling and recovery: a review10.1016/j.reactfunctpolym.2007.05.004 ↗
2. The effect of hard segment length on the thermal and mechanical properties of polyurethane/graphene oxide nanocomposites10.1016/j.compositesa.2014.11.010 ↗
3. Shedding new light on polyurethane degradation: assessing foams condition in design objects10.1016/j.polymdegradstab.2017.08.028 ↗
4. Rigid polyurethane foams with infused nanoclays: relationship between cellular structure and thermal conductivity10.1016/j.eurpolymj.2016.04.026 ↗
5. Plastics - the Facts 2016, an analysis of European plastics production, demand and waste data 2016 Accessed 16.9.2017.
6. R. Zevenhoven, Treatment and disposal of polyurethane wastes: options for recovery and recycling. Report TKK-ENY-19. June 2004.
7. PU foam derived from renewable sources: perspective on properties enhancement: an overview10.1016/j.eurpolymj.2017.08.022 ↗
8. Recycling and disposal methods for polyurethane foam wastes10.1016/j.proenv.2012.10.023 ↗
9. EC (European Commission) · 2013
10. Recycling of waste from polymer materials: an overview of the recent works10.1016/j.polymdegradstab.2013.09.025 ↗
11. Thermoplastic polyurethanes with glycolysate intermediates from polyurethane waste recycling10.1016/j.polymdegradstab.2017.09.001 ↗
12. Mechanical and chemical recycling of solid plastic waste10.1016/j.wasman.2017.07.044 ↗
13. Use of waste materials in the construction industry
14. Durability of lightweight masonry mortars made with white recycled polyurethane foam10.1016/j.cemconcomp.2012.07.006 ↗
15. Proportioning and characterization of lightweight concrete mixtures made with rigid polyurethane foam wastes10.1016/j.cemconcomp.2008.06.007 ↗
16. Lightweight mortar made with recycled polyurethane foam10.1016/j.cemconcomp.2010.07.017 ↗
17. Valorization of coarse rigid polyurethane foam waste in lightweight aggregate concrete10.1016/j.conbuildmat.2009.11.010 ↗
18. An overview on the potential of geopolymers for concrete infrastructure rehabilitation10.1016/j.conbuildmat.2012.07.003 ↗
19. Effect of elevated temperatures on geopolymer paste, mortar and concrete10.1016/j.cemconres.2009.10.017 ↗
20. Geopolymer mortars as sustainable repair material: a comprehensive review10.1016/j.rser.2017.05.076 ↗
21. Geopolymer concrete: a review of some recent developments10.1016/j.conbuildmat.2015.03.036 ↗
22. Davidovits · 2008
23. The solidification of aluminum production waste in geopolymer matrix10.1016/j.jclepro.2014.04.043 ↗
24. Enhancement of the properties of fly ash based geopolymer paste by incorporating ground granulated blast furnace slag10.1016/j.conbuildmat.2017.04.139 ↗
25. The development of Bayer derived geopolymers as artificial aggregates10.1016/j.hydromet.2016.05.001 ↗
26. Stiffness and deformation properties of spent coffee grounds based geopolymers10.1016/j.conbuildmat.2017.01.082 ↗
27. Designing water resistant lightweight geopolymers produced from waste materials10.1016/j.matdes.2011.09.016 ↗
28. Physical and mechanical properties of lightweight aerated geopolymer10.1016/j.conbuildmat.2015.01.043 ↗
29. Lightweight geopolymer made of highly porous siliceous materials with various Na2O/Al2O3 and SiO2/Al2O3 ratios10.1016/j.msea.2011.04.044 ↗
30. Lightweight geopolymer concrete containing aggregate from recycle lightweight block10.1016/j.matdes.2013.06.001 ↗
31. Lightweight concretes of activated metakaolin-fly ash binders, with blast furnace slag aggregates10.1016/j.conbuildmat.2009.12.024 ↗
32. Thermal treatment of kaolin clay to obtain metakaolin10.2298/HEMIND100322014I ↗
33. Synthesis and mechanical properties of metakaolinite-based geopolymer10.1016/j.colsurfa.2005.01.016 ↗
34. EN-1015-11:2007 “Methods of test for mortar for masonry. Part 11 - Determination of flexural and compressive strength of hardened mortars”.
35. DIN 18555-9:1998 Testing of mortars containing mineral binders - Hardened mortars – Part 9: Determination of the mortar compressive strength in the bed joint - 1998.
36. Influence of sample thickness and capping on characterization of bedding mortars from historic masonries by double punch test (DPT)10.4028/www.scientific.net/KEM.624.322 ↗
37. Estimation of soil and grout thermal properties through a TSPEP (two-step parameter estimation procedure) applied to TRT (thermal response test) data10.1016/j.energy.2010.12.031 ↗
38. Inverse heat conduction problem: sensitivity coefficient insights, filter coefficients, and intrinsic verification10.1016/j.ijheatmasstransfer.2016.02.034 ↗
39. A simplex method for function minimization10.1093/comjnl/7.4.308 ↗
40. Influence of degree of dehydroxylation on the pozzolanic activity of metakaolin10.1016/j.clay.2009.01.014 ↗
41. Infrared spectroscopy study of structural nature of geopolymeric products10.1007/s11595-007-4522-7 ↗
42. Geopolymers from jordanian metakaolin: influence of chemical and mineralogical compositions on the development of mechanical properties
43. Synthesis and characterization of polyurethane elastomers10.1177/0095244307085540 ↗
44. Organically modified montmorillonite hyperbranched polyurethane–urea hybrid composites10.1016/j.porgcoat.2007.07.001 ↗
45. Water-dispersed polymers for the conservation and restoration of Cultural Heritage: a molecular, thermal, structural and mechanical characterisation10.1016/S0142-9418(00)00027-1 ↗
46. Physico-mechanical and WAXS studies of PU/PS semi interpenetrating polymer networks10.1016/j.eurpolymj.2006.11.004 ↗
47. Rietveld refinement of the kaolinite structure at 1.5 k10.1346/CCMN.1993.0410613 ↗
48. Preparation and properties of alkali activated metakaolin-based geopolymer10.3390/ma9090767 ↗
49. Geopolymer technology for application-oriented dense and lightened materials. Elaboration and characterization10.1016/j.ceramint.2015.06.140 ↗
50. Thermal treatment of kaolin: the effect of mineralogy on the pozzolanic activity10.1016/S0169-1317(01)00040-0 ↗
51. Optimization of the metakaolin geopolymer preparation for maximized ammonium adsorption capacity10.1007/s10853-017-1156-9 ↗
52. Bulk composition and microstructure dependence of effective thermal conductivity of porous inorganic polymer cements10.1016/j.jeurceramsoc.2011.12.030 ↗
53. Mortar compressive strength estimation by applying various experimental test methods10.1016/j.proeng.2017.02.172 ↗
54. The geopolymerisation of alumino-silicate minerals10.1016/S0301-7516(99)00074-5 ↗
55. Hybrid organic-inorganic materials: a land of multidisciplinary10.1039/JM9960600511 ↗
56. Novel hybrid organic-geopolymer materials10.1016/j.clay.2012.11.001 ↗
57. Non-standard testing of mechanical characteristics of historic mortars10.1080/15583051003717788 ↗
58. An intermingled fractal units model to evaluate pore size distribution influence on thermal conductivity values in porous materials10.1016/j.applthermaleng.2014.01.037 ↗
59. Porosity and pore size distribution influence on thermal conductivity of yttria-stabilized zirconia: experimental findings and model predictions10.1016/j.ceramint.2015.12.122 ↗