journal article·2016-09

Fibre distribution and orientation of macro-synthetic polyolefin fibre reinforced concrete elements

M.G. Alberti, A. Enfedaque, J.C. Gálvez, V. Agrawal

Publisher page

Abstract

Abstract Fracture behaviour of polyolefin fibre reinforced concrete (PFRC) has proved to be suitable for structural design in construction elements. As in other fibre reinforced materials, the tensile behaviour is strongly affected by the positioning of the fibres. Previous research has assessed this influence by means of fracture tests, showing reliable results. These were obtained by changing the most influencing parameters: the fibre length, the pouring and compaction methods, the concrete type and specimen sizes. However, the influence of these factors in fracture results is merely limited to the fracture surfaces, while the positioning of the fibres in the rest of the piece may be a key factor for design in structural elements. Furthermore, examination of the orientation factor within the whole piece provides relevant information about the behaviour of the fibres during the pouring processes. It may also allow preparation of future models to predict the final positioning of the fibres. This paper examines the positioning and orientation of the fibres in elements which provided fracture results previously reported in the literature. In addition to counting the fibres located in the fracture surfaces, the specimens were divided in portions. The fibre-positioning maps obtained provide sound and useful conclusions that may be considered in future design of PFRC elements. The data gathered showed how the orientation-factor varied with the flux and vibration, absence of any tendency to float and the noticeable influence of the pouring point in fibre distribution. It also showed that this type of fibre is suitable for structural-size elements, improving the orientation factor for longer distances when using self-compacting concrete.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Innovations in Concrete and Construction Materials · Structural Behavior of Reinforced Concrete

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. Tensile strength of concrete affected by uniformly distributed and closely spaced short lengths of wire reinforcement
2. Design of FRC tunnel segments considering the ductility requirements of the MC-2010 – Application to the BarcelonaMetro Line 9
3. Steel fibers reinforcement for precast lining in tunnels with different diameters
4. Simplified method for concrete pavement design with discrete structural fibers10.1016/j.conbuildmat.2006.08.008 ↗
5. Structural cast-in-place SFRC: technology, control criteria and recent applications in Spain10.1617/s11527-009-9540-9 ↗
6. First ultra-high-performance fibre-reinforced concrete footbridge in Spain: design and construction10.2749/101686614X13830788505793 ↗
7. Fibre-reinforced concrete in fib Model Code 2010: principles, models and test validation10.1002/suco.201300021 ↗
8. fib Model Code, Model Code, Paris: Fédération Internationale du Béton fib/International Federation for Structural Concrete, 2010.
9. CNR-DT 204 · 2006
10. EHE-08 · 2008
11. Ugbolue · 2009
12. Structural application of polyolefin fiber reinforced concrete
13. McIntyre · 2004
14. On the mechanical properties and fracture behavior of polyolefin fiber-reinforced self-compacting concrete10.1016/j.conbuildmat.2014.01.024 ↗
15. Alberti · 2015
16. Plastic fibres as the only reinforcement for flat suspended slabs: experimental investigation and numerical simulation10.1016/j.conbuildmat.2014.01.082 ↗
17. Comparison between polyolefin fibre reinforced vibrated conventional concrete and self-compacting concrete10.1016/j.conbuildmat.2015.03.007 ↗
18. Polyolefin fiber-reinforced concrete enhanced with steel-hooked fibers in low proportions10.1016/j.matdes.2014.03.050 ↗
19. Application of high performance polypropylene fibers in concrete lining of water tunnels10.1016/j.matdes.2013.09.075 ↗
20. Durability of cracked fibre reinforced shotcrete
21. The use of steel and synthetic fibres in concrete under extreme conditions
22. Use of macro plastic fibres in concrete: a review10.1016/j.conbuildmat.2015.05.105 ↗
23. Open-loop recycling: a LCA case study of PET bottle-to-fibre recycling10.1016/j.resconrec.2010.06.014 ↗
24. Investigation of fiber distribution in concrete batches discharged from ready-mix truck10.1007/s40069-014-0083-2 ↗
25. Development of recycled PET fiber and its application as concrete-reinforcing fiber10.1016/j.cemconcomp.2007.02.002 ↗
26. A life cycle assessment of recycled polypropylene fibre in concrete footpaths
27. Effect of inclining angle, bundling and surface treatment on synthetic fibre pull-out from a cement matrix10.1016/0010-4361(90)90005-H ↗
28. Pull-out behaviour of hooked steel fibres10.1007/BF02483148 ↗
29. Pull-out behaviour and interface critical parameters of polyolefin fibres embedded in mortar and self-compacting concrete matrixes10.1016/j.conbuildmat.2016.02.128 ↗
30. Electromagnetic quality control of steel fiber concrete10.1016/j.conbuildmat.2014.09.101 ↗
31. Assessment of fibre orientation in reinforced concrete using Fourier image transform10.1046/j.1365-2818.1998.00393.x ↗
32. Ponikiewski · 2014
33. Automatic image analysis and morphology of fibre reinforced concrete10.1016/S0958-9465(99)00025-6 ↗
34. Flowability of fibre-reinforced concrete and its effect on the mechanical properties of the material10.1016/j.conbuildmat.2010.02.025 ↗
35. Rebound and orientation of fibers in wet sprayed concrete applications10.1016/j.conbuildmat.2013.07.051 ↗
36. Framework to predict the orientation of fibers in FRC: a novel philosophy10.1016/j.cemconres.2012.02.013 ↗
37. Placing conditions, mesostructural characteristics and post-cracking response of fibre reinforced self-compacting concretes10.1016/j.conbuildmat.2009.11.008 ↗
38. Fracture mechanics of polyolefin fibre reinforced concrete: study of the influence of the concrete properties, casting procedures, the fibre length and specimen size10.1016/j.engfracmech.2015.12.032 ↗
39. Fibre distribution in macro-plastic fibre reinforced concrete slab-panels10.1016/j.conbuildmat.2014.04.067 ↗
40. Reliability of polyolefin fibre reinforced concrete beyond laboratory sizes and construction procedures10.1016/j.compstruct.2015.12.068 ↗
41. EN 197-1 · 2012
42. EN 14651:2007+A1 · 2007
43. RILEM TC-162-TDF · 2002
44. Simple tools for fiber orientation prediction in industrial practice10.1016/j.cemconres.2011.05.008 ↗
45. Fibre spacing and specific fibre surface
46. Distribution and orientation of fibers in steel fiber reinforced concrete
47. The effect of fibre distribution characteristics on the flexural strength of steel fibre-reinforced ultra high strength concrete10.1016/j.conbuildmat.2010.11.057 ↗
48. Distribution of steel fibres in rectangular sections10.1016/j.cemconcomp.2004.03.005 ↗
49. Characterization of the orientation profile of steel fiber reinforced concrete10.1617/s11527-010-9686-5 ↗
50. On flow properties, fibre distribution, fibre orientation and flexural behaviour of FRC10.1617/s11527-007-9229-x ↗
51. Round-robin analysis of the RILEM TC 162-TDF beam-bending test: Part 3—Fibre distribution10.1007/BF02483283 ↗
52. Spatial distribution of steel fibres in sprayed and cast concrete10.1680/macr.2003.55.3.225 ↗
53. Measurement of energy dissipation mechanisms in fracture of fiber-reinforced ultrahigh-strength cement-based composites