journal article·2020-04

Properties of high-volume iron tailing powder concrete under different curing conditions

Fanghui Han, Ao Luo, Juanhong Liu, Zengqi Zhang

Publisher page

Abstract

Abstract The mechanical properties, microstructure and permeability of high-volume iron tailing powder (HVITP) concrete and high-volume fly ash (HVFA) concrete were comparatively investigated by measuring the adiabatic temperature rise, rate of temperature rise, compressive strength, splitting tensile strength and chloride permeability grade of concrete and determining the pore structure, bound water content and morphology of paste. The total adiabatic temperature rise of HVITP concrete are lower than that of HVFA concrete. But the early higher rate of temperature rise of HVITP concrete is obtained. The HVITP concrete shows low compressive strength and splitting tensile strength, coarse pore structure, loose microstructure and high chloride permeability compared with HVFA concrete with the same water/binder ratio. The early temperature matching curing (TMC) adversely affects the later-age properties development of HVITP concrete, but it promotes the properties development of HVFA concrete. The decrease in water/binder ratio or the partial replacement of ITP with slag improves the properties of HVITP concrete, especially for the early properties under TMC condition. But these two means still lead to properties difference between HVITP concrete and HVFA concrete due to the low reactivity of ITP.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Magnesium Oxide Properties and Applications · Concrete and Cement Materials Research · Advanced materials and composites

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (40)

Show source-provided references
1. Fresh properties, compressive strength and microstructure of fly ash geopolymer paste blended with iron ore tailing under thermal cycle10.1016/j.conbuildmat.2016.05.059 ↗
2. Effects of quartz-based mine tailings on characteristics and leaching behavior of ultra-high performance concrete10.1016/j.conbuildmat.2018.01.087 ↗
3. Characterization of mortars with iron ore tailings using destructive and nondestructive testes10.1016/j.conbuildmat.2016.11.065 ↗
4. Evaluation of iron ore tailings as replacement for fine aggregate in concrete10.1016/j.conbuildmat.2016.05.095 ↗
5. A comparative study on the practical utilization of iron tailings as a complete replacement of normal aggregates in dam concrete with different gradation10.1016/j.jclepro.2018.11.107 ↗
6. Development of green engineered cementitious composites using iron ore tailings as aggregates10.1016/j.conbuildmat.2013.03.088 ↗
7. Utilization of iron ore tailings as fine aggregate in ultra-high performance concrete10.1016/j.conbuildmat.2013.10.019 ↗
8. Test research on the effects of mechanochemically activated iron tailings on the compressive strength of concrete10.1016/j.conbuildmat.2016.05.020 ↗
9. Early-age hydration characteristics of composite binder containing ITP10.1016/j.powtec.2017.04.022 ↗
10. Innovative methodology for comprehensive utilization of iron ore tailings part 2: The residues after iron recovery from iron ore tailings to prepare cementitious material10.1016/j.jhazmat.2009.09.019 ↗
11. Properties of steam-cured precast concrete containing iron tailings powder10.1016/j.powtec.2019.01.007 ↗
12. Use of grounded iron ore tailings (GIOTs) and BaCO3 to improve sulfate resistance of pastes10.1016/j.conbuildmat.2017.05.209 ↗
13. Reuse of hazardous electrolytic manganese residue: detailed leaching characterization and novel application as a cementitious material10.1016/j.resconrec.2019.104645 ↗
14. A review on fly ash characteristics-towards promoting high volume utilization in developing sustainable concrete10.1016/j.jclepro.2017.01.114 ↗
15. Investigation on the poor fluidity of electrically conductive cement-graphite paste: experiment and simulation10.1016/j.matdes.2019.107679 ↗
16. Effect of fly ash microsphere on the rheology and microstructure of alkali-activated fly ash/slag pastes10.1016/j.cemconres.2018.04.008 ↗
17. Characteristics and applications of fly ash as a sustainable construction materials: a state-of-the-art review10.1016/j.resconrec.2018.04.010 ↗
18. Hydration of fly ash cement10.1016/j.cemconres.2004.09.008 ↗
19. Effect of size fraction and glass structure of siliceous fly ashes on fly ash cement hydration10.1016/j.jiec.2013.03.032 ↗
20. The differences among the roles of ground fly ash in the paste, mortar and concrete10.1016/j.conbuildmat.2015.05.117 ↗
21. Hydration kinetics of composite binder containing fly ash at different temperatures10.1007/s10973-016-5295-z ↗
22. Effect of fly ash on the kinetics of Portland cement hydration at different temperatures10.1016/j.cemconres.2011.02.005 ↗
23. Characteristics of the hydration heat evolution of composite binder at different hydrating temperature10.1016/j.tca.2014.04.010 ↗
24. The volumetric stability, chloride binding capacity and stability of the Portland cement-GBFS pastes: an approach from the viewpoint of hydration products10.1016/j.conbuildmat.2019.02.026 ↗
25. Comparison of the properties between high-volume fly ash concrete and high-volume steel slag concrete under temperature matching curing condition10.1016/j.conbuildmat.2015.08.134 ↗
26. Creep and thermal cracking of ultra-high volume fly ash mass concrete at early age10.1016/j.cemconcomp.2019.02.018 ↗
27. Influence of limestone on the hydration of ternary slag cements10.1016/j.cemconres.2017.05.013 ↗
28. Properties of high-volume limestone powder concrete under standard curing and steam-curing conditions10.1016/j.powtec.2016.05.054 ↗
29. Design and experimental study of a ternary blended cement containing high volume steel slag and blast-furnace slag based on Fuller distribution model10.1016/j.conbuildmat.2017.02.119 ↗
30. Effect of water/binder ratio on the hydration kinetics of composite binder containing slag or fly ash10.1007/s10973-016-6015-4 ↗
31. Hydration of slag-blended cements10.1016/j.cemconcomp.2012.05.007 ↗
32. Recent advances in understanding the role of supplementary cementitious materials in concrete10.1016/j.cemconres.2015.03.018 ↗
33. Hydration heat of slag or fly ash in the composite binder at different temperatures10.1016/j.tca.2017.07.002 ↗
34. Modeling the hydration of concrete incorporating fly ash or slag10.1016/j.cemconres.2010.03.001 ↗
35. Modeling of structural performances under coupled environmental and weather actions10.1007/BF02480352 ↗
36. Multi-level diffusion model for manufactured sand mortar considering particle shape and limestone powder effects10.1016/j.conbuildmat.2019.02.139 ↗
37. Comparative study of reaction degree of mineral admixture by selective dissolution and image analysis10.1016/j.conbuildmat.2016.03.221 ↗
38. Multi-scale modelling for diffusivity based on practical estimation of interfacial properties in cementitious materials10.1016/j.powtec.2016.11.036 ↗
39. Quantification of the influences of aggregate shape and sampling method on the overestimation of ITZ thickness in cementitious materials10.1016/j.powtec.2017.12.008 ↗
40. Composition and microstructure of 20-year-old ordinary Portland cement-ground granulated blast-furnace slag blends containing 0 to 100% slag10.1016/j.cemconres.2010.02.012 ↗