Experimental investigation of utilizing waste flue gas desulfurized gypsum as backfill materials
Source abstract
Abstract
Abstract Flue gas desulfurized gypsum (FGDG) is a waste material produced in the power stations during the flue gas desulfurization process. In China, a small amount of FGDG is used as cement additives or for gypsum boards, but there still exist a mass of FGDG due to the lack of reusing methods. Also, the waste fly ash (WFA) is another waste material from the power plant. To alleviate the accompanying environmental issues, large-volume utilizations such as in civil engineering applications are usually adopted to consume these materials. However, these materials cannot achieve high strength due to the lack of amorphous content. In this study, combined with WFA, a large volume of waste FGDG was investigated for the utilizations as backfill materials. With using two types of activators, sodium hydroxide and water glass, in small doses, mixtures with various ratios of FGDG and WFA were included to investigate the mechanical, chemical, microscopic, and softening properties at different curing periods. Then the field experiments including the dynamic cone penetration test and the load plate test were conducted to evaluate the bearing capacity, settlement and compaction effect of the compacted mixtures. The experimental results showed that the NaOH activated mixture (FGDG: WFA = 50:50) could acquire acceptable mechanical properties for backfill applications, which can serve as a practical option for the large-volume utilization of FGDG and WFA.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Recycled Aggregate Concrete Performance
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (41)
Show source-provided references
1. Compressive strength and microstructural characteristics of class C fly ash geopolymer10.1016/j.cemconcomp.2009.11.003 ↗
2. Gypsum for agricultural use in Ohio: sources and quality of available products, Ohio State University Extension Fact Sheet
3. Evaluation of permeability characteristics of FGD materials10.1016/S0016-2361(98)00138-0 ↗
4. Flue gas desulfurization gypsum: study of basic mechanical, hydric and thermal properties10.1016/j.conbuildmat.2006.05.009 ↗
5. Use of waste gypsum to replace natural gypsum as set retarders in portland cement10.1016/j.wasman.2008.11.014 ↗
6. Alternative calcium-sulfate-bearing materials as cement retarders: Part II. FGD gypsum10.1016/j.cemconres.2004.03.021 ↗
7. Microstructure and strength of blended FBC-PCC fly ash geopolymer containing gypsum as an additive10.2306/scienceasia1513-1874.2012.38.175 ↗
8. Improved geopolymerization of bottom ash by incorporating fly ash and using waste gypsum as additive10.1016/j.cemconcomp.2012.04.001 ↗
9. Use of gypsum as a preventive measure for strength deterioration during curing in class F fly ash geopolymer system10.3390/ma8063053 ↗
10. Preparation of α-calcium sulfate hemihydrate from FGD gypsum in K, Mg-containing concentrated CaCl2 solution under mild conditions10.1016/j.fuel.2009.01.004 ↗
11. Thermal treatment and utilization of flue gas desulphurization gypsum as an admixture in cement and concrete10.1016/j.conbuildmat.2007.04.001 ↗
12. Mineralogical and engineering characteristics of dry flue gas desulfurization products
13. Verification of lime and water glass stabilized FGD gypsum as road sub-base10.1016/j.fuel.2009.11.029 ↗
14. Utilization of fly ash blends from pulverized coal and fluidized bed combustions in geopolymeric materials10.1016/j.cemconcomp.2010.09.017 ↗
15. Strength, microstructure, efflorescence behavior and environmental impacts of waste glass geopolymers cured at ambient temperature10.1016/j.jclepro.2019.119610 ↗
16. Strength properties of geopolymers derived from original and desulfurized red mud cured at ambient temperature10.1016/j.conbuildmat.2016.08.144 ↗
17. Mechanical and microstructural characterization of geopolymers derived from red mud and fly ashes10.1016/j.jclepro.2018.03.086 ↗
18. Investigation of the strength development of cast-in-place geopolymer piles with heating systems10.1016/j.jclepro.2019.01.155 ↗
19. Stabilization/solidification of hazardous wastes using fly ash10.1061/(ASCE)0733-9372(1996)122:10(935) ↗
20. Chemically stabilized soft clays for road-base construction10.1061/(ASCE)MT.1943-5533.0001156 ↗
21. Utilization of marble dust, fly ash and waste sand (Silt-Quartz) in road subbase filling materials10.1007/s12205-012-1526-4 ↗
22. Mechanical property and microstructure characteristics of geopolymer stabilized aggregate base10.1016/j.conbuildmat.2018.10.081 ↗
23. Feasible use of recycled concrete aggregates and crushed clay brick as unbound road sub-base10.1016/j.conbuildmat.2005.01.045 ↗
24. Sustainable stabilization/solidification of municipal solid waste incinerator fly ash by incorporation of green materials10.1016/j.jclepro.2019.03.057 ↗
25. Recycling dredged sediment into fill materials, partition blocks, and paving blocks: technical and economic assessment10.1016/j.jclepro.2018.07.165 ↗
26. Value-added recycling of construction waste wood into noise and thermal insulating cement-bonded particleboards10.1016/j.conbuildmat.2016.08.053 ↗
27. A novel type of controlled low strength material derived from alum sludge and green materials10.1016/j.conbuildmat.2018.01.078 ↗
28. Select engineering characteristics of crushed glass10.1061/(ASCE)0899-1561(2004)16:6(526) ↗
29. Evaluation of glass powder-based geopolymer stabilized road bases containing recycled waste glass aggregate10.1177/0361198119898695 ↗
30. Construction of a test embankment using a sand-tire shred mixture as fill material10.1016/j.wasman.2005.10.009 ↗
31. Use of light-weight treated soils made of waste soil in airport extention project10.2208/jscej.2000.644_13 ↗
32. Engineering characteristics of rubber-added lightweight soil as a flowable backfill material10.1061/(ASCE)MT.1943-5533.0000307 ↗
33. Stabilization of expansive soil using waste ceramic dust
34. Effect of source and particle size distribution on the mechanical and microstructural properties of fly Ash-Based geopolymer concrete10.1016/j.conbuildmat.2018.01.193 ↗
35. Shear and deformation characteristics of municipal waste combustor bottom ash for highway applications10.3141/1577-13 ↗
36. Geotechnical engineering properties of incinerator ash mixes10.1080/10473289.2004.10470959 ↗
37. GB 51004-2015. Code for acceptance of construction quality of building foundation, Ministry of Construction of the People’s Republic of China.
38. China highway research institute and Ministry of transport. Technical Guidelines for Construction of Highway Road Bases (2015).
39. Characteristics and applications of fly ash as a sustainable construction material: a state-of-the-art review10.1016/j.resconrec.2018.04.010 ↗
40. Enhancing the engineering properties of expansive soil using bagasse ash and hydrated lime
41. Plasticity, swell-shrink, and microstructure of phosphogypsum admixed lime stabilized expansive soil10.1155/2016/9798456 ↗