Strengthening of steel–concrete composite girders using carbon fiber reinforced polymer plates
Source abstract
Abstract
Abstract Strengthening and rehabilitation of structures is a major concern for researchers in the civil engineering community in recent years due to the aging of these structures and the need for effective methods of strengthening. This paper presents the results of an experimental study of the behavior of strengthened steel–concrete composite girders using Carbon Fiber Reinforced Polymers (CFRP) plates. Strengthening was achieved by attaching the CFRP plates to the bottom flange and in some beams the CFRP plates were also attached to the beam web. Two different types of CFRP plates were used being mainly different in the tensile modulus of elasticity. Shear stress distribution along the bond line between CFRP plates and steel was recorded and reported. The test results showed that using lightweight CFRP plates could enhance the strength and stiffness of steel–concrete composite girders up to 45% of the original strength.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Structural Load-Bearing Analysis · Concrete Corrosion and Durability
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (13)
Show source-provided references
1. Federal Highway Adminstration (FHWA). Available from: , Washington, DC; 2001.
2. Klaiber FW, Dunker KF, Wipf TJ, Sanders WW. Methods of strengthening existing highway bridges. NCHRP Report No. 293, TRB, National Research Council, Washington, DC; 1987. p. 114.
3. Dorton RA, Reel R. Methods for increasing live load capacity of existing highway bridges. NCHRP Synthesis 249, TRB, National Research Council, Washington, DC; 1997. p. 66.
4. Stress analysis and failure properties of carbon-fibre-reinforced-plastic/steel lap joints10.1080/00218468608073238 ↗
5. Adams · 1997
6. 1983
7. Springer GS. Environmental effects on epoxy matrix composites. In: Tsai SW, editor. Proceedings of the fifth conference on composite materials: testing and design. ASTM STP 674, American Society for Testing and Materials; 1979. p. 291–312.10.1520/STP36915S ↗
8. Chajes MJ, Mertz DR, Thomson TA, Farschman CA. Durability of composite materials reinforcement. In: Basham KD, editor. Proceedings of the third materials engineering conference on infrastructure: new materials and methods of repair. San Diego, California; 1994. p. 598–605.
9. Roy A, Grontcharova-Benard E, Gacougnolle J-L, Davies, P. Hygrothermal effects on failure mechanisms of composites/steel bonded joints. In: Schapery RA, Sun CT, editors. Time dependent and nonlinear effects in polymer and composites, West Coshhocken, PA: ASTM STP 1357, American Society for Testing and Materials; 2000. p. 357–71.10.1520/STP15843S ↗
10. Accelerated marine aging of composites and composite/metal joints
11. Sen R, Liby L, Spillet K, Mullins G. Strengthening steel composite bridge members using CFRP laminates. In: Taerwe L, editor. Proceedings of the second international RILEM symposium on non-metallic (FRP) reinforcement for concrete structures, Ghent, Belgium; 1995. p. 551–8.
12. Mertz DR, Gillespie JW. Rehabilitation of steel bridge girders through the application of advanced composites materials. Final Report, NCHRP –93-ID011, TRB. Washington, DC: National Research Council; 1996. p. 30.
13. Hognestad E. A study of combined bending and axial load in reinforced concrete members. Bulletin No. 399, University of Illinois Engineering Experimental Station; 1951.