journal article·2017-10

Effect of placement temperature and curing method on plastic shrinkage of plain and pozzolanic cement concretes under hot weather

Muhammad Nasir, Omar S. Baghabra Al-Amoudi, Mohammed Maslehuddin

Publisher page

Abstract

Abstract This paper reports the results of a study conducted to investigate the effect of concrete placement temperature and curing method on the plastic shrinkage of plain and pozzolanic cement concretes. The concrete specimens were cast at a temperature of 25, 32, 38 or 45 °C and exposed to the ambient summer conditions. The specimens were cured by applying a water-based curing compound or covering with a plastic sheet. The performance of ordinary Portland (Type I) cement, fly ash (FA), very fine fly ash (VFFA), silica fume (SF), blast furnace slag (BFS) and natural pozzolan (NP) was evaluated by measuring the plastic shrinkage strain. The results indicated that the curing compound was effective in decreasing the shrinkage strain in all concretes. It was also noted that the critical temperature at which the maximum shrinkage strain occurred was 25 °C and as the concrete temperature was approaching the ambient temperature, the shrinkage strain decreased. The 28-day compressive and split tensile strength and pulse velocity were also determined to study the effect of placement temperature on these properties. These data indicated that the critical placement temperature was both 25 and 45 °C while the optimum temperature for all cementitious materials was either 32 or 38 °C.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Concrete Properties and Behavior · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. Neville · 2010 · 844
2. Orchard · 1979
3. Rixom · 1986
4. Water evaporation from freshly placed concrete surfaces in hot weather10.1016/0008-8846(89)90035-5 ↗
5. Concrete Construction in Hot Weather
6. ACI Committee 305, Guide to Hot Weather Concreting, Farmingt. Hills, Mich. Am. Concr. Institute, 2010, pp. 23.
7. Soroka · 1979
8. Effect of environmental conditions on the properties of fresh and hardened concrete10.1016/S0958-9465(01)00007-5 ↗
9. Probable mechanism of crack formation at early ages of concretes: a literature survey
10. Saudi Building Code National Committee, Saudi Building Code 304°C, first ed, Arabia Saudi, 2007, pp. 290.
11. Evaporation of water from fresh mortar and concrete at different environmental conditions
12. Placing and shrinkage at extreme temperatures
13. Concrete mixture design for hot weather: experimental and statistical analyses10.1680/macr.1998.50.2.95 ↗
14. Shirley · 1980 · 7
15. Influence of cement composition and content on the corrosion behavior of reinforcing steel in concrete
16. Corrosion of reinforcing steel in concrete containing slag or pozzolans
17. Hot weather concreting with admixtures10.1016/S0958-9465(98)80005-X ↗
18. Effect of mix proportions on plastic shrinkage cracking of concrete in hot environments10.1016/S0950-0618(98)00019-1 ↗
19. Effect of casting temperature on strength and density of plain and blended cement concretes prepared and cured under hot weather conditions10.1016/j.conbuildmat.2016.02.211 ↗
20. Influence of practical curing methods on evaporation of water from freshly placed concrete in hot climates10.1016/S0360-1323(00)00048-2 ↗
21. Effectiveness of portland cement concrete curing compound10.3141/1834-08 ↗
22. Membrane curing of concrete: moisture loss10.1016/0008-8846(94)90160-0 ↗
23. Use of a new approach (design of experinments method) to study different procedures to avoid plastic shrinkage cracking of concrete in hot climates10.3151/jact.9.149 ↗
24. Effect of curing methods on the properties of plain and blended cement concretes10.1016/j.conbuildmat.2009.08.036 ↗
25. Effect of curing methods on shrinkage and corrosion resistance of concrete10.1016/j.conbuildmat.2012.12.064 ↗
26. Plastic shrinkage in hot and arid environments
27. Control of plastic shrinkage cracking in cold weather
28. Large pours - 2, heat generation and control