Influence of cold weather during casting and curing on the stiffness and strength of concrete
Source abstract
Abstract
Abstract The supposition that casting and curing at near freezing temperatures leads to the loss of stiffness of the hardened concrete and causes microstructure disruption and abnormalities was investigated. The research programme reported here involved 25 concrete slabs, 750 × 750 × 300 mm, which were subjected to various curing regimes in the range of 20 °C to −5 °C. The extent of loss of stiffness and the degree of microcracking were quantified using the Stiffness Damage Test (SDT). This test method has previously been shown by one of the authors to be very effective in quantifying the extent of disruption to the microstructure of concrete caused by various damage mechanisms. In addition to the SDT, the cold-cured concrete was evaluated by the full stress–strain test as well as ultrasonic, dynamic, and petrographic methods. Concreting at temperatures near freezing resulted in approximately 20% reduction of the 28 day stiffness and a Damage Index of 5 as determined by the SDT. Cold weather curing resulted in the development of microcracks in the paste and adversely affected the interfacial zone. Storage of the constituents of concrete at near freezing conditions prior to mixing adversely affects the long term stiffness and strength of concrete. The water absorption of hardened concrete increased as a result of cold-curing. The loss of stiffness because of low temperature curing is not remedied by using stiff aggregate such as granite nor by PFA cement replacement.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Concrete Properties and Behavior · Innovative concrete reinforcement materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (22)
Show source-provided references
1. ACI 306 Committee. Guide to cold weather concreting. ACI 306R-10, American Concrete Institute, Farmington Hills, Michigan, USA; 2010, pp. 26.
2. Powers · 1962
3. Kosmatka · 2003
4. Influence of environmental temperatures on the concrete compressive strength: simulation of hot and cold weather conditions10.1016/j.cemconres.2005.01.004 ↗
5. Properties of early-stage concrete with setting-accelerating tablet in cold weather10.1016/j.msea.2011.10.066 ↗
6. Energy-efficient approach to cold-weather concreting10.1061/(ASCE)MT.1943-5533.0000262 ↗
7. BS 1881–111: 1983. Testing Concrete-Part 111: Methods of normal curing of test specimens (20°C method). British Standards Institute: London; 1983.
8. BS EN 12390-2:2009. Testing hardened concrete. British Standards Institute: London; 2009.
9. A new quantitative method for assessing fire-damaged concrete structures10.1680/macr.1995.47.172.271 ↗
10. Nassif AY. Assessment of the fractured state of fire damaged concrete. PhD Thesis, University of London; 1996.
11. A proposed new classification index for fire damaged concrete based on the strain energy dissipated in a hysteresis loop10.1680/macr.2000.52.4.287 ↗
12. Nassif A. Assessment of damaged and deteriorating concrete using the Stiffness Damage Test. In: Proceeding of the Eighth East Asia-Pacific conference on structural engineering & construction, Singapore, December 2001.
13. Postfire full stress–strain response of fire-damaged concrete10.1002/fam.911 ↗
14. BS1881-203:1986. Testing Concrete-Part203: Recommendations for measurements of velocity of ultrasonic pulses in concrete. British Standards Institute: London; 1986.
15. BS EN 12504-4:2004. Testing Concrete-Part 4: Determination of the ultrasonic pulse velocity. British Standards Institute: London; 2004.
16. BS 1881-209:1990. Testing Concrete-Part 209: Recommendation for the measurements of the dynamic modulus of elasticity. British Standards Institute: London; 2004.
17. DIN 52617:1987-05. Determination of the water absorption coefficient of construction materials.
18. DIN EN ISO 15148:2003-03. Hydrothermal performance of building materials and products – determination of water absorption coefficient by partial immersion (ISO 15148:2002); German version EN ISO 15148:2002.
19. BS 1881-12:1983. Testing concrete-Part 121: Method for determination of static modulus of elasticity in compression. British Standard Institute: London; 2003.
20. Aitcin · 1983
21. Klieger · 1958
22. Neville · 2000