journal article·2013-06

Analytical approach for the evaluation of minimum fibre factor required for steel fibrous concrete beams under combined shear and flexure

Constantin E. Chalioris

Publisher page

Abstract

Abstract The use of steel fibres as shear resistance mass reinforcement has been well-documented and the possibility of partially or even fully replacing of stirrups with steel fibres has been examined. However, issues of common engineering practice about the optimum content of steel fibres in shear-dominated fibrous concrete beams have not yet been fully clarified. This study presents an analytical approach to the aforementioned question. The proposed methodology is initially based on the calculations of the flexural and shear capacities of a steel fibrous concrete element and to the concept that a pure flexural response should be achieved. The target of this method is to evaluate the minimum fibre factor, F, required in order that a fibrous concrete beam to satisfy pre-set strength and ductility requirements. The well-known fibre factor expresses the effect of both the volume fraction and the geometrical characteristics of the used steel fibres and its calculation is achieved by a concluding cubic formula derived from the proposed procedure. Steel fibres can be used either as the only shear reinforcement or in combination with a minimum or a desirable amount of stirrups. A database of 256 tested beams collected from 17 existing works around the world is used to establish the validity of the proposed approach. Comparisons between experimental data and predicted results derived from the analytical procedure showed a very good agreement. Two numerical examples of a typical shear-critical beam and a rather short edge-loaded cantilever slab that illustrate the application of the described method are also presented herein. Further, analytical curves and design charts have been plotted by the implementation of the proposed approach as an analysis tool for parametrical study. The influence of the concrete strength, the span-to-depth ratio, the tension steel longitudinal reinforcement and the amount of the provided stirrups on the value of the fibre factor has also been investigated and discussed.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Structural Behavior of Reinforced Concrete · Concrete Corrosion and Durability

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (45)

Show source-provided references
1. ACI Committee 544. State-of-the-art on fiber reinforced concrete. ACI Manual of concrete practice. Farmington Hills (MI): American Concrete Institute; 1998.
2. Flexural analysis of reinforced concrete beams containing steel fibers10.1061/(ASCE)0733-9445(1992)118:10(2821) ↗
3. Shear strength of beams with deformed steel fibers
4. Shear performance of steel fibrous concrete beams10.1016/j.proeng.2011.07.259 ↗
5. Fiber reinforced concrete beams with circular section in torsion
6. Nonlinear analysis and tests of steel-fiber concrete beams in torsion10.12989/sem.2000.9.4.323 ↗
7. Effectiveness of the use of steel fibres on the torsional behaviour of flanged concrete beams10.1016/j.cemconcomp.2009.02.007 ↗
8. RILEM TC 162-TDF. Test and design methods for steel fibre reinforced concrete, σ-ε design method. Mater Struct/Mater Construct 2003;36(262):560–7.10.1617/14007 ↗
9. National Research Council. Guide for the design and construction of fiber-reinforced concrete structures. CNR-DT 204/2006, Rome; 2007.
10. Flexural performance of fibre reinforced concrete made with steel and synthetic fibres10.1016/j.conbuildmat.2012.06.042 ↗
11. Optimization of reinforced fibrous concrete beams
12. Size effect in shear failure of longitudinally reinforced beams
13. Experimental validation of smeared analysis for plain concrete in torsion10.1061/(ASCE)0733-9445(2000)126:6(646) ↗
14. Shear strength of fibrous concrete beams without stirrups10.1061/(ASCE)0733-9445(1986)112:9(2066) ↗
15. Use of steel fibers as shear reinforcement
16. Influence of steel fibres on the shear resistance of lightweight concrete T-beams
17. Shear strength of steel fiber-reinforced concrete beams without stirrups
18. Prediction of shear strength of steel fiber RC beams using neural networks10.1016/j.conbuildmat.2005.01.047 ↗
19. Shear stress prediction: steel fiber-reinforced concrete beams without stirrups
20. Shear behaviour of fiber reinforced concrete beams10.1016/S0958-9465(97)00031-0 ↗
21. Experimental and theoretical investigation on the shear of steel fibre reinforced concrete beams10.1016/S0141-0296(98)00049-2 ↗
22. Effectiveness of stirrups and steel fibres as shear reinforcement10.1016/j.cemconcomp.2003.07.001 ↗
23. The diagonal tension behavior of fiber reinforced concrete beams10.1016/j.cemconcomp.2006.12.009 ↗
24. Synergetic effect of steel fibers and shear-reinforcing bars on the shear-resistance mechanisms of RC linear members10.1016/j.conbuildmat.2010.05.009 ↗
25. Shear behavior of fiber-reinforced self-consolidating concrete slender beams
26. Replacing stirrups of self-compacting concrete beams with steel fibers10.1007/s12209-010-1416-0 ↗
27. The composite effect of steel fibres and stirrups on the shear behaviour of beams using self-consolidating concrete10.1016/j.engstruct.2010.09.023 ↗
28. Shear behaviour of steel fibre reinforced self-consolidating concrete beams based on the modified compression field theory10.1016/j.compstruct.2012.02.025 ↗
29. Predicting the shear strength of steel fiber reinforced concrete beams10.1016/j.conbuildmat.2011.06.042 ↗
30. Triaxial tests of fiber-reinforced concrete10.1061/(ASCE)0899-1561(2001)13:5(340) ↗
31. Acoustic emission characterization of the fracture process in fibre reinforced concrete10.1016/j.conbuildmat.2011.04.049 ↗
32. Influence of fiber chemical coating on the acoustic emission behavior of steel fiber reinforced concrete10.1016/j.cemconcomp.2011.07.003 ↗
33. Stirrup effectiveness in reinforced concrete beams under flexure and shear
34. Evaluation of shear strength of fibre reinforced concrete beams10.1016/0958-9465(90)90045-Y ↗
35. CEN. Eurocode 2. Design of concrete structures – Part 1–1: General rules and rules for buildings. EN 1992-1-1: 2004:E, 2004.
36. Analysis and experimental study for steel fibre pullout from cementitious matrices10.1177/096369350000900401 ↗
37. Shear strength of steel fiber-reinforced concrete beams without web reinforcement
38. Naaman AE, Reinhardt HW. High performance fiber reinforced cement composites: HPFRCC 4. In: RILEM Proceedings Pro 30. RILEM Publications S.A.R.L.; 2003. p. 95–113.10.1007/BF02479507 ↗
39. Shear strength of normal and high-strength fiber reinforced concrete beams without stirrups
40. Steel fibrous RC beams subjected to cyclic deformations under predominant shear10.1016/j.engstruct.2012.10.010 ↗
41. Shear and moment capacity of reinforced steel-fibre-concrete beams10.1680/macr.1987.39.140.148 ↗
42. Shear behavior of high-strength fiber reinforced concrete beams
43. Shear behavior of steel fiber reinforced concrete beams
44. Beams of fibrous concrete in shear and bending: experiment and model10.1061/(ASCE)0733-9445(2000)126:2(243) ↗
45. Zeris C, Vitalis A, Kontogiannis P. Experimental investigation of steel fiber reinforced concrete beams without shear reinforcement (in Greek). In: Proceedings sixteenth hellenic concrete conference, Pafos, Cyprus; 2009. Paper ID: m2456_zeris. .