journal article·2016-04

Prediction of masonry compressive behaviour using a damage mechanics inspired modelling method

Tatheer Zahra, Manicka Dhanasekar

Publisher page

Abstract

Masonry under compression is affected by the properties of its constituents and their interfaces. In spite of extensive investigations of the behaviour of masonry under compression, the information in the literature cannot be regarded as comprehensive due to ongoing inventions of new generation products – for example, polymer modified thin layer mortared masonry and drystack masonry. As comprehensive experimental studies are very expensive, an analytical model inspired by damage mechanics is developed and applied to the prediction of the compressive behaviour of masonry in this paper. The model incorporates a parabolic progressively softening stress-strain curve for the units and a progressively stiffening stress-strain curve until a threshold strain for the combined mortar and the unit-mortar interfaces is reached. The model simulates the mutual constraints imposed by each of these constituents through their respective tensile and compressive behaviour and volumetric changes. The advantage of the model is that it requires only the properties of the constituents and considers masonry as a continuum and computes the average properties of the composite masonry prisms/wallettes; it does not require discretisation of prism or wallette similar to the finite element methods. The capability of the model in capturing the phenomenological behaviour of masonry with appropriate elastic response, stiffness degradation and post peak softening is presented through numerical examples. The fitting of the experimental data to the model parameters is demonstrated through calibration of some selected test data on units and mortar from the literature; the calibrated model is shown to predict the responses of the experimentally determined masonry built using the corresponding units and mortar quite well. Through a series of sensitivity studies, the model is also shown to predict the masonry strength appropriately for changes to the properties of the units and mortar, the mortar joint thickness and the ratio of the height of unit to mortar joint thickness. The unit strength is shown to affect the masonry strength significantly. Although the mortar strength has only a marginal effect, reduction in mortar joint thickness is shown to have a profound effect on the masonry strength. The results obtained from the model are compared with the various provisions in the Australian Masonry Structures Standard AS3700 (2011) and Eurocode 6.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Masonry and Concrete Structural Analysis · Hygrothermal properties of building materials · Building materials and conservation

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Mechanics of masonry in compression10.1061/(ASCE)0733-9445(1985)111:4(857) ↗
2. Mechanics of masonry in compression: results from a homogenisation approach10.1016/j.compstruc.2006.08.054 ↗
3. Standards Australia, AS3700 Australian Standards for Masonry Structures, 2011.
4. American Concrete Institute (ACI) · 2005
5. BSI, EN 1996-1-1:2005 Eurocode 6: design of masonry structures – Part 1–1: Common rules for reinforced and unreinforced masonry structures, Brussels, 2005.
6. Compression behavior and failure mechanisms of concrete masonry prisms
7. Experimental investigation and numerical analysis of tuff-brick listed masonry panels10.1617/s11527-012-9884-4 ↗
8. Characterization of the uniaxial compression behaviour of unreinforced masonry—Sensitivity analysis based on a numerical and experimental approach10.1016/j.acme.2014.06.007 ↗
9. Validation of analytical and continuum numerical methods for estimating the compressive strength of masonry10.1016/j.compstruc.2006.08.009 ↗
10. CDM model for residual strength of concrete under cyclic compression10.1016/S0958-9465(02)00090-2 ↗
11. Damage constitutive of concrete under uniaxial alternate tension–compression fatigue loading based on double bounding surfaces10.1016/j.ijsolstr.2004.01.026 ↗
12. Elasto-damage model for high strength concrete subjected to multiaxial loading10.1177/1056789506065914 ↗
13. Models for the compressibility of layered polymeric sponges10.1002/pen.760310212 ↗
14. Mechanical behaviour of brick masonry panels under uniaxial compression10.2140/jomms.2014.9.385 ↗
15. Mechanical behaviour of earthen materials: a comparison between earth block masonry, rammed earth and cob10.1016/j.conbuildmat.2014.03.009 ↗
16. A. Smith, F. Verhelst, C. Denayer, R. Givens, Quantifying the benefits of lime additions in cement based mortars, in: Proceedings of the IMC 2014, 9th International Masonry Conference, Guimarães, Portugal, 2014.
17. Compressive strength predictions of hollow concrete block masonry prisms
18. O.S. Izquierdo, M.R.S. Corrêa, I.I. Soto, The influence of mortar bedding on the compressive strength of concrete block masonry structures, in: Proceedings of the IB2MaC, 15th International Brick and Block Masonry Conference, Florianopolis, Brazil, 2012.
19. Influence of joint thickness and mortar-block elastic properties on the strength and stresses developed in soil–cement block masonry10.1061/(ASCE)0899-1561(2009)21:10(535) ↗
20. E.S. Fortes, M.J.A. Santos, R.L. Canato, G.A. Parsekian, Prisms strength built with thin joint polymeric mortar compared to regular mortar joint, in: Proceedings of 12th Canadian Masonry Symposium, Vancouver, British Columbia, 2013.
21. Study of the compressive strength of blockwork masonry
22. Assessment of compressive behaviour of concrete masonry prisms partially filled by general mortar10.1061/(ASCE)MT.1943-5533.0000956 ↗
23. R.P. Andolfato, J.S. Camacho, R.M. Mauricio, Study of structural masonry concrete block units and prisms varying the blocks cement quantity and degree of compaction, in: Proceedings of the 7th Australasian masonry conference, Newcastle, Australia, 2004, pp. 150–160. ISBN: 1 9207 0141 9.
24. On the compressive strength prediction for concrete masonry prisms10.1617/s11527-009-9492-0 ↗
25. L. Binda, A. Fontana, G. Frigerio, Mechanical behaviour of brick masonries derived from unit and mortar characteristics, in: Proceedings of 8th International Brick and Block Masonry Conference, Dublin, 1988.
26. Mechanical response of solid clay brickwork under eccentric loading. Part I: Unreinforced masonry10.1007/BF02479351 ↗
27. S. Das, J. Liu, M. El-Sayed, G. Sturgeon, Effect of height-to-thickness ratio on compressive strength of hollow concrete masonry, in: Proceedings of the CMS 2013, 12th Canadian Masonry Symposium, Vancouver, British Columbia, 2013.10.70803/001c.138228 ↗
28. G. Mohamed, Mechanics of hollow concrete block masonry ruptures (Master in Civil Engineering Dissertation), Federal University of Santa Catarina, Florianopolis, 1998.
29. Mechanics of hollow concrete block masonry prisms under compression: review and prospects10.1016/j.cemconcomp.2006.11.003 ↗
30. Effects of joint thickness adhesion and web shells to the face shell bedded concrete masonry loaded in compression10.7158/S12-035.2013.14.3 ↗
31. Sahlin · 1971
32. The prediction of compressive strength of ungrouted hollow concrete block masonry10.1016/j.conbuildmat.2014.01.025 ↗