Properties of the mechanical in controlled low-strength rubber lightweight aggregate concrete (CLSRLC)
Source abstract
Abstract
Abstract In this study, waste rubber tire powder and reservoir silt lightweight aggregate were added to controlled low-strength material (CLSM) to produce a renewable building material. The results showed that the slump in the controlled low-strength rubber lightweight aggregate concrete (CLSRLC) containing different amounts of rubber was more than 190 mm. The compressive strength and drop-weight value decreased with rubber particle replacement percentages up to 20%, but the design strength requirement (>0.7 MPa) was still met. The lowest shrinkage in CLSRC was achieved at a rubber particle replacement percentage of 20%. The electrical resistivity was less than 10 kΩ-cm at an age of 91 days. The ultrasonic pulse velocity decreased as the rubber particle replacement percentage increased. Sulfate resistance increases with increasing rubber particle replacement percentage. The research results showed that rubber particle replacement percentages in the range of 10–20% are feasible in engineering practice. These special engineering materials can meet special requirements in Taiwan while contributing to the reduced consumption of natural resources and reduced damage to the natural environment, thus helping meet goals for waste recycling, energy savings, carbon reduction and safe and sustainable reuse of materials.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Innovative concrete reinforcement materials · Structural Behavior of Reinforced Concrete · Concrete and Cement Materials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (40)
Show source-provided references
1. A study of the engineering properties of CLSM with a new type of slag10.1016/j.conbuildmat.2015.10.198 ↗
2. Influence of high temperature high pressure curing on compressive strength and elasticity modulus of lightweight aggregate concrete
3. Wang · 2007 · 114
4. Study on durability of densified high-performance lightweight aggregate concrete10.12989/cac.2007.4.6.499 ↗
5. Engineering properties of lightweight aggregate concrete made from dredged silt10.1016/j.cemconcomp.2005.12.005 ↗
6. Performance characteristics of dredged silt and high-performance lightweight aggregate concrete10.12989/cac.2010.7.1.053 ↗
7. Lee Ming · 2005
8. The effects of cement fly ash ratios on the volcanic slag aggregate lightweight concrete masonry units10.1016/j.conbuildmat.2007.05.011 ↗
9. Investigation of properties of low-strength lightweight concrete for thermal insulation
10. Waste tire fiber modified concrete
11. Static and dynamic behavior of recycled tire rubber-filled concrete
12. Mechanical properties of concrete containing a high volume of tire-rubber particles10.1016/j.wasman.2008.01.015 ↗
13. Mechanical properties of concrete containing a high volume of tire-rubbk R, properties of concrete containing scrap tire rubber – an overview10.1016/j.wasman.2004.01.006 ↗
14. Correlation of strength, rubber content, and water to cement ratio in rubberized concrete10.1139/l05-063 ↗
15. Scrap-tyre-rubber replacement for aggregate and filler in concrete10.1016/j.conbuildmat.2008.09.020 ↗
16. Feasibility study of a soil-based rubberized CLSM10.1016/j.wasman.2008.06.017 ↗
17. Properties of crumb rubber concrete
18. Properties of concrete pedestrian block mixed with crumb rubber10.1016/j.conbuildmat.2005.01.040 ↗
19. Properties of concrete paving blocks incorporating crumb rubber and SBR latex10.1080/14680629.2009.9690188 ↗
20. Possibility of using waste tire rubber and fly ash with Portland cement as construction materials10.1016/j.wasman.2008.11.002 ↗
21. Improvement of chloride ion penetration resistance in cement mortars modified with rubber from worn automobile tires10.1016/j.cemconcomp.2009.04.004 ↗
22. Effects of rubber aggregates from grinded used tyres on the concrete resistance to cracking10.1016/j.jclepro.2011.09.016 ↗
23. A review of the fresh/hardened properties and applications of plain-(PRC) and self-compacting rubberized concrete (SCRC)10.1016/j.conbuildmat.2010.04.056 ↗
24. Experimental investigation of some fresh and hardened properties of rubberized self-compacting concrete10.1016/j.matdes.2008.12.011 ↗
25. Zheng Rui Bin, Technical Overview and History of CLSM, Taiwan Concrete Institute – Concrete Technology, vol. 8, no. 4, 2009, pp. 64–74.
26. Utilization of waste materials and by-products in producing controlled low-strength materials10.1016/j.resconrec.2009.06.001 ↗
27. Kuo · 2014
28. Kuo · 2013
29. High-carbon fly ash in manufacturing conductive CLSM and concrete10.1061/(ASCE)0899-1561(2006)18:6(743) ↗
30. Performance of industrial by-products in controlled low-strength materials (CLSM)10.1016/j.wasman.2007.03.030 ↗
31. Steel furnace slag aggregate expansion and hardened concrete properties10.1016/j.cemconcomp.2015.04.006 ↗
32. ASTM C150, Standard Specification for Portland Cement, USA, ASTM International.
33. ASTM C143, Standard Test Method for Slump of Hydraulic-Cement Concrete, USA, ASTM International.
34. ASTMC39, Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens, USA, ASTM International.
35. ASTM C597, Standard Test Method for Pulse Velocity Through Concrete, USA, ASTM International.
36. ASTM C157, Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete, USA, ASTM International.
37. ASTM C876, Standard Test Method for Corrosion Potentials of Uncoated Reinforcing Steel in Concrete, USA, ASTM International.
38. ASTM C1012, Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution, USA, ASTM International.
39. CNS 3763, Waterproof agent of cement for concrete construction, CNS Online Service.
40. CNS 13295, Compressed concrete paving units, CNS Online Service.