journal article·2020-01

Performance of AC mixtures containing flakes of LDPE plastic film collected from urban waste considering ageing

Arminda Almeida, Silvino Capitão, Rita Bandeira, Mariana Fonseca, Luís Picado-Santos

Publisher page

Abstract

Abstract This paper evaluates the performance of asphalt concrete (AC) mixtures containing flakes of low density polyethylene (LDPE) waste plastic film. After optimum plastic content was defined, moisture susceptibility and workability were assessed. Subsequently, performance was evaluated considering unaged and aged specimens by testing for stiffness, fatigue and rutting resistance. Compared with non-modified mixture, the unaged plastic-modified mixture presented fair moisture susceptibility, acceptable workability, better resistance to traffic-compaction, higher stiffness, higher rutting resistance and slightly lower fatigue resistance. After ageing, the modified mixture performed better in all these aspects. Therefore, incorporating LDPE waste into AC is feasible with environmental and technical benefits.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (71)

Show source-provided references
1. European Parliament News, Plastic waste and recycling in the EU: facts and figures, 2018.
2. Mepex Consult AS, Basic Facts Report on Design for Plastic Packaging Recyclability, 2017.
3. Plastic flexible films waste management – a state of art review10.1016/j.wasman.2018.04.023 ↗
4. European Commission, Plastic Waste: Ecological and Human Health Impacts (In-depth Reports), e European Commission’s Directorate-General Environment and edited by the Science Communication Unit, the University of the West of England (UWE), Bristol, 2011.
5. European Commission, REPORT FROM THE COMMISSION TO THE EUROPEAN PARLIAMENT, THE COUNCIL, THE EUROPEAN ECONOMIC AND SOCIAL COMMITTEE AND THE COMMITTEE OF THE REGIONS on the implementation of EU waste legislation, including the early warning report for Member States at risk of missing the 2020 preparation for re-use/recycling arget on municipal waste COM(2018) 656 final, 2018.
6. European Commission, A European Strategy for Plastics in a Circular Economy, 2018.
7. M. Crippa, B. De Wilde, R. Koopmans, J. Leyssens, J. Muncke, A.-C. Ritschkoff, K. Van Doorsselaer, C. Velis, M.A. Wagner, A circular economy for plastics – insights from research and innovation to inform policy and funding decisions, Directorate-General for Research and Innovation (European Commission), Brussels, Belgium, 2019.
8. European Commission, COMMUNICATION FROM THE COMMISSION TO THE EUROPEAN PARLIAMENT, THE COUNCIL, THE EUROPEAN ECONOMIC AND SOCIAL COMMITTEE AND THE COMMITTEE OF THE REGIONS – A European Strategy for Plastics in a Circular Economy – COM/2018/028 final, 2018.
9. Polymer modified asphalt binders10.1016/j.conbuildmat.2005.07.007 ↗
10. A review of using waste and virgin polymer in pavement10.1016/j.conbuildmat.2012.01.009 ↗
11. Using waste polymers as a reliable alternative for asphalt binder modification – performance and morphological assessment10.1016/j.conbuildmat.2018.11.279 ↗
12. Use of plastic wastes from greenhouse in asphalt mixes manufactured by dry process
13. Influence of aging on properties of polymer-modified asphalt10.1016/j.conbuildmat.2018.11.105 ↗
14. Laboratory evaluation of HMA with high density polyethylene as a modifier10.1016/j.conbuildmat.2010.12.037 ↗
15. Effect of HDPE based wastes on the performance of modified asphalt mixtures10.1016/j.proeng.2016.08.567 ↗
16. 12 – Recycling of PET in asphalt concrete
17. Effect of waste plastic bottles on the stiffness and fatigue properties of modified asphalt mixes10.1016/j.matdes.2014.04.046 ↗
18. Value-added application of waste PET based additives in bituminous mixtures containing high percentage of reclaimed asphalt pavement (RAP)10.1016/j.jclepro.2018.06.119 ↗
19. A.F. Ahmad, A.R. Razali, I.S.M. Razelan, Utilization of polyethylene terephthalate (PET) in asphalt pavement: a review, IOP Conference Series: Materials Science and Engineering 203 (2017) 012004 10.1088/1757-899x/203/1/012004.10.1088/1757-899X/203/1/012004 ↗
20. The effect of polypropylene fibers on asphalt performance10.1016/j.buildenv.2007.02.011 ↗
21. Impact of polypropylene application method on long-term aging of polypropylene-modified HMA10.1061/(ASCE)MT.1943-5533.0000105 ↗
22. 6 – Polypropylene fiber-reinforced bitumen
23. Incorporation of waste plastic in asphalt binders to improve their performance in the pavement
24. A sustainable approach: utilization of waste PVC in asphalting of roads10.1016/j.conbuildmat.2013.12.050 ↗
25. Rutting behavior of hot mix asphalt modified by polyvinyl chloride powder10.1080/10916466.2017.1336772 ↗
26. R. F, R. H, M. L, Caracterización dinámica de una mezcla densa en caliente modificada con un desecho de policloruro de vinilo (PVC), XV Congreso Ibero Latinoamericano del Asfalto, Lisbon, Portugal, 2009.
27. Laboratory evaluation of ethylene vinyl acetate modified bitumens and mixtures based upon performance related parameters10.1016/j.conbuildmat.2012.09.109 ↗
28. Engineering properties of EVA-modified bitumen binder for paving mixes10.1061/(ASCE)0899-1561(1999)11:2(131) ↗
29. Rheological properties and stability of ethylene vinyl acetate polymer-modified bitumen10.1002/pen.23462 ↗
30. Rheology and stability of bitumen/EVA blends10.1016/j.eurpolymj.2004.06.001 ↗
31. D.N. Little, Enhancement of Asphalt Concrete Mixtures to Meet Structural Requirements through the Addition of Recycled Polyethylene, in: H.F. Waller (Ed.), ASTM International, West Conshohocken, PA, 1993, pp. 210-230.10.1520/STP19852S ↗
32. Utilization of reclaimed polyethylene in bituminous paving mixes10.1061/(ASCE)0899-1561(2002)14:6(527) ↗
33. The use of polyethylene in hot asphalt mixtures10.3844/ajassp.2007.390.396 ↗
34. Behavior of asphalt concrete mixtures with reclaimed polyethylene as additive10.1061/(ASCE)0899-1561(2007)19:6(500) ↗
35. Effect of low-density polyethylene on fracture toughness of asphalt concrete mixtures10.1061/(ASCE)MT.1943-5533.0000106 ↗
36. Recycling waste packaging tape into bituminous mixtures towards enhanced mechanical properties and environmental benefits10.1016/j.jclepro.2019.04.409 ↗
37. Using polymers to improve the rutting resistance of asphalt concrete10.1016/j.conbuildmat.2014.12.060 ↗
38. Laboratory and in-situ tests for estimating improvements in asphalt concrete with the addition of an LDPE and EVA polymeric compound10.1016/j.conbuildmat.2018.11.152 ↗
39. IPQ, NP EN 13108-1. Misturas betuminosas Especificações dos materiais Parte 1: Betão betuminoso (Bituminous mixtures – Material specifications – Part 1: Asphalt concrete), 2011.
40. IPQ, NP EN 12591: Betumes e ligantes betuminosos – Especificações para betumes de pavimentação (Bitumen and bituminous binders – Specifications for paving grade bitumens), 2011.
41. Improving asphalt mixture performance by partially replacing bitumen with waste motor oil and elastomer modifiers10.3390/app7080794 ↗
42. Asphalt rubber concrete fabricated by the dry process: laboratory assessment of resistance against reflection cracking10.1016/j.conbuildmat.2017.11.081 ↗
43. IP, Paving Materials Specifications (in Portuguese), Infraestruturas de Portugal, 2014.
44. CEN, EN12697-30. Bituminous mixtures – Test methods for hot mix asphalt – Part 30: Specimen prepared by impact compactor, 2012.
45. CEN, EN12697-6. Bituminous mixtures - Test methods for hot mix asphalt - Part 6: Determination of bulk density of bituminous specimens, 2012.
46. CEN, EN12697-34. Bituminous mixtures – Test methods for hot mix asphalt – Part 34: Marshall test, 2004.
47. CEN, EN12697-5. Bituminous mixtures – Test methods for hot mix asphalt – Part 5: Determination of the maximum density, 2018.
48. CEN, EN12697-8. Bituminous mixtures – Test methods for hot mix asphalt – Part 8: Determination of void characteristics of bituminous specimens, 2012.
49. CEN, EN12697-12. Bituminous mixtures – Test methods for hot mix asphalt – Part 12: Determination of the water sensitivity of bituminous specimens, 2018.
50. CEN, EN12697-23. Bituminous mixtures – Test methods for hot mix asphalt – Part 23: Determination of the indirect tensile strength of bituminous specimens, 2017.
51. Assessment of the workability of bituminous mixtures
52. Austroads, Development of an Asphalt Workability Index: Pilot Study, 2006.
53. D. Gardete, L. Picado-Santos, S. Capitão, Avaliação da trabalhabilidade de misturas betuminosas com base nas curvas de compactação (Evaluation of the workability of asphalt mixtures using compaction curves), In Proceedings of the 8°Congresso Rodoviário Português (8th Portuguese Road Conference), Lisbon, Portugal, 2016.
54. Compactibility of hot bituminous mixtures made with crumb rubber-modified binders10.1016/j.conbuildmat.2007.02.005 ↗
55. Optimization of constructibility and resistance to traffic: a new design approach for HMA using the superpave compactor
56. CEN, EN12697-10. Bituminous mixtures – Test methods for hot mix asphalt – Part 10: Compactability, 2017.
57. Faheem · 2004
58. CEN, EN12697-26. Bituminous mixtures – Test methods for hot mix asphalt – Part 26: Stiffness, 2004.
59. CEN, EN12697-24. Bituminous mixtures – Test methods for hot mix asphalt – Part 24: Resistance to fatigue, 2007.
60. Design temperature on flexible pavements10.1080/14680629.2000.12067148 ↗
61. CEN, EN12697-22. Bituminous mixtures – Test methods for hot mix asphalt – Part 22: Wheel tracking, 2007.
62. AASHTO, Standard Practice for Mixture Conditioning of Hot Mix Asphalt (HMA) – AASHTO Designation: R 30-02, American Association of State Highway and Transportation Officials, 2015.
63. Dynamic modulus and phase angle prediction of laboratory aged asphalt mixtures10.1016/j.conbuildmat.2018.09.160 ↗
64. Effect of long-term ageing on properties of RAP inclusive WMA mixes10.1016/j.conbuildmat.2019.02.087 ↗
65. Influence of short and long term aging on chemical, microstructural and macro-mechanical properties of recycled asphalt mixtures10.1016/j.conbuildmat.2013.11.004 ↗
66. CEN, EN 13108-1. Bituminous mixtures – Material specifications – Part 1: Asphalt Concrete, 2011.
67. Optimization of warm mix asphalts using different blends of binders and synthetic paraffin wax contents10.1016/j.conbuildmat.2010.02.030 ↗
68. Recycled asphalt mixtures produced with high percentage of different waste materials10.1016/j.conbuildmat.2015.03.063 ↗
69. Mechanical performance of asphalt concrete modified with nanoparticles: nanosilica, zero-valent iron and nanoclay10.1016/j.conbuildmat.2018.06.052 ↗
70. Effect of aging conditions on the fatigue behavior of hot and warm mix asphalt10.1016/j.conbuildmat.2018.08.119 ↗
71. Evaluation of the durability of asphalt concrete modified with nanomaterials using the TEAGE aging method10.1016/j.conbuildmat.2019.04.121 ↗