journal article·2020-05

Physical and mechanical properties of natural rubber modified cement paste

Gampanart Sukmak, Patimapon Sukmak, Suksun Horpibulsuk, Teerasak Yaowarat, Kittipong Kunchariyakun, Orasa Patarapaiboolchai, Arul Arulrajah

Publisher page

Abstract

Abstract Cemented materials have high compressive strength but low toughness and flexural strength. This research evaluated improvement of toughness and flexural strength of cemented materials with the addition of natural rubber (NR), based on the results from extensive testing of the cemented pastes. While mixing with cement (C), Sodium dodecyl sulfate (SDS) was used as a surfactant admixture to provide stability to the NR particles. The natural rubber modified cement (NRMC) pastes were prepared by varying the influence factors, namely: SDS/C ratio, SDS to dry rubber content (SDS/DRC) ratio, and DRC/C ratio at the same water to cement (W/C) ratio of 0.55. The DRC/C ratios were varied in the range of 0–50%. The role of the influence factors on bulk density, setting time, temperature of setting paste, compressive and flexural strengths, and toughness of NRCM pastes were also studied in this research. Scanning electron microscopy (SEM) images and energy dispersive spectrometry (EDS) were carried out on the NRCM pastes to confirm on the presence of NR films and air bubble in the NRMC pastes. The bulk density was found to decrease in proportion to the increases in the SDS/C and DRC/C ratios. The addition of NR latex was found to improve the flexural strength and toughness, whilst retarding the setting time and hydration. The flexural strength was found to be increased with increasing DRC/C, up to the optimal value. Beyond this optimal value, the flexural strength decreased but with higher flexural deflection. The optimum SDS/DRC ratio of 10% and DRC/C ratio of 10 provided the highest compressive and flexural strengths of NMPC paste. The knowledge gained from this study provides useful information for further research and practice in infrastructure engineering applications such as earthquake-resistant lightweight cement wall and impact-resistance products.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Structural Behavior of Reinforced Concrete · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (42)

Show source-provided references
1. Experimental investigation of the effect of latex solid/water ratio on latex modified co-matrix mechanical properties10.1016/j.aej.2012.11.002 ↗
2. SBR latex modified mortar rheology and mechanical behaviour10.1016/j.cemconres.2003.09.006 ↗
3. Influence of polymer type on adhesion performance of a blended cement mortar10.1016/j.ijadhadh.2013.01.007 ↗
4. Polymer film formation in cement mortars modified with water-soluble polymers10.1016/j.cemconcomp.2014.11.015 ↗
5. Impact of admixtures on the hydration kinetics of Portland cement10.1016/j.cemconres.2011.03.005 ↗
6. Retardation effect of styrene-acrylate copolymer latexes on cement hydration10.1016/j.cemconres.2015.04.014 ↗
7. Influence of water-cement ratio and cement content on the properties of polymer-modified mortars10.1016/S0008-8846(99)00060-5 ↗
8. The use of wool as fiber-reinforcement in cement-based mortar10.1016/j.conbuildmat.2016.10.096 ↗
9. Experimental investigation of the behavior composite steel-concrete composite beams containing different amounts of steel fibres and conventional reinforcement10.1016/j.conbuildmat.2019.01.026 ↗
10. Experimental study on shear properties of aligned steel fiber reinforced cement-based composites10.1016/j.conbuildmat.2018.06.026 ↗
11. Optimization of fibre reinforcement for waste aggregate cement composite10.1016/j.conbuildmat.2012.09.057 ↗
12. Reinforcement effects of polyvinyl alcohol and polypropylene fibers on flexural behaviors of sulfoaluminate cement matrices10.1016/j.cemconcomp.2018.02.004 ↗
13. Uniaxial compression mechanical properties and fracture characteristics of brucite fiber reinforced cement-based composites10.1016/j.compstruct.2019.01.030 ↗
14. Physical and mechanical properties of styrene–butadiene rubber emulsion modified cement mortars10.1016/j.cemconres.2004.07.012 ↗
15. The AC response of polymer-coated mortar specimens10.1016/S0008-8846(02)00741-X ↗
16. Properties of latex blends and its modified cement mortars10.1016/S0008-8846(02)00813-X ↗
17. Laboratory and field performance of polymer-modified cement-based repair mortars in cold climates10.1016/S0950-0618(02)00027-2 ↗
18. Hong · 2015 · 379
19. An insight into Hevea – Phytophthora interaction: the story of Hevea defense and Phytophthora counter defense mediated through molecular signalling10.1016/j.cpb.2018.11.009 ↗
20. Mark · 2007
21. High performance natural rubber/thermally reduced graphite oxide nanocomposites by latex technology10.1016/j.compositesb.2014.08.010 ↗
22. Whiting · 1998
23. Preparation of composites of natural rubber latex–Portland cement for moulds10.1002/(SICI)1097-0126(199804)45:4<339::AID-PI930>3.0.CO;2-T ↗
24. Effect of surfactants on the yield stress of cement paste10.1016/j.cemconres.2017.04.015 ↗
25. The morphology of entrained air voids in hardened cement paste generated with different anionic surfactants10.1016/j.cemconcomp.2008.02.003 ↗
26. Unit weight, strength and microstructure of water treatment sludge-fly ash geopolymer lightweight cellular geopolymer10.1016/j.conbuildmat.2015.07.091 ↗
27. ASTM-C192, Standard practice for making and curing concrete test specimens in the laboratory, 2016.
28. ASTM-C39, Standard test method for compressive strength of cylin-drical concrete specimens, 2016.
29. ASTM-C293, Standard test method for flexural strength of concrete (using simple beam with center-point loading), 2016.
30. ASTM-C191, Standard test methods for time of setting of hydraulic cement by Vicat needle, 2013.
31. Interactions between organic and inorganic phases in PA- and PU/PA-modified-cement-based materials10.1061/(ASCE)MT.1943-5533.0000302 ↗
32. Effect of polyvinyl alcohol on the hydration of cement with rice husk ash10.1016/S0008-8846(00)00475-0 ↗
33. Compressive and flexural strength of polyvinyl alcohol–modified pavement concrete using recycled concrete aggregates10.1061/(ASCE)MT.1943-5533.0002233 ↗
34. Effects of the charge characteristics of polycarboxylate superplasticizers on the adsorption and the retardation in cement pastes10.1016/j.cemconres.2014.10.004 ↗
35. Numerical simulation of hydration and microstructural development in hardening cement-based materials (I) theory10.1016/0008-8846(95)00017-8 ↗
36. Methods for calculating activation energy for Portland cement
37. Change in reaction kinetics of a Portland cement caused by a superplasticizer — Calculation of heat flow curves from XRD data10.1016/j.cemconres.2011.10.005 ↗
38. Effects of the molecular architecture of comb-shaped superplasticizers on their performance in cementitious systems10.1016/j.cemconcomp.2006.12.006 ↗
39. S. Pourchet, C. Comparet, L. Nicoleau, A. Nonat, Influence of polycarboxylate superplasticizers on tricalciumsilicate hydration. Proceedings of the 12th International Congress on the Chemistry of Cement, Montréal, Canada, 2007, pp. 132–145.
40. Proposed structure for calcium silicate hydrate gel10.1111/j.1151-2916.1986.tb07446.x ↗
41. Kan, Effects of specimen size on strength and drying shrinkage of polymer-modified concrete10.1016/0262-5075(82)90026-4 ↗
42. Recycled concrete aggregate modified with polyvinyl alcohol and fly ash for concrete pavement applications10.1061/(ASCE)MT.1943-5533.0002751 ↗