Properties of unfired, illitic-clay bricks for sustainable construction
Source abstract
Abstract
Illitic clays are used for brickmaking worldwide. This paper explores the feasibility of using these clays unfired, to lower the environmental impact of construction. The results suggest that illitic clay can be used unfired. The geotechnical parameters of the clay are within the limits considered suitable for earth construction, and the compressive and flexural strengths fall within recommended limits in earth standards. Masonry constructed with the unfired illitic brick, bound with a standard hydraulic-lime mortar would reach a 28-day strength of 2.45 N/mm2 which meets structural requirements in some European masonry standards. Stabilization improved durability but lowered strength and vapour permeability, and did not significantly change thermal properties. The results suggest that both the quantity and composition of the clay fraction in an earth material determine the success of stabilization. The strength reduction caused by lime stabilization is mainly attributed to the adsorption of the Ca2+ by the illite, which prevents free Ca2+ from taking part in the pozzolanic reaction that builds up strength. The extremely high specific surface area of the illitic clay particles (24 m2/g) enhanced lime adsorption consequently damaging pozzolanic reaction and strength development. If half of an annual production of 15 million brick was unfired, producers would economise over 4 million euros in kiln fuel and carbon tax in 10 years, and would approximately half their carbon emissions, lowering massively the global environmental impact of brick production.
Source: openalex_inverted_index · Quality: baseline
Research context
OpenAlex topics: Hygrothermal properties of building materials · Building materials and conservation · Recycling and utilization of industrial and municipal waste in materials production
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (93)
Show source-provided references
1. In-plant production of bricks containing waste foundry sand
2. U.S. Geological Survey (2019) Mineral Commodity Summaries. USA Dept of the Interior. February 19.
3. Flanagan · 2018
4. Comparative life cycle assessment of ceramic brick, concrete brick and cast-in-place reinforced concrete exterior walls10.1016/j.jclepro.2016.07.069 ↗
5. EU Ceramic Manufacturing Industry Report. European Commission. August 2007. https://eippcb.jrc.ec.europa.eu/reference/BREF/cer_bref_0807.pdf.
6. Carbon footprint of solid clay bricks fired in clamps of India10.1016/j.jclepro.2016.06.152 ↗
7. Engineering properties of unfired clay masonry bricks10.1016/j.enggeo.2009.05.002 ↗
8. Life cycle analysis of environmental impacts of earthen materials in the Portuguese context: Rammed earth and compressed earth blocks10.1016/j.jclepro.2019.118286 ↗
9. Low embodied energy cement stabilised rammed earth building—a case study10.1016/j.enbuild.2013.09.051 ↗
10. Embodied energy and CO2 analyses of mud-brick and cement-block houses10.3934/energy.2014.1.18 ↗
11. Cradle to site Life Cycle Assessment (LCA) of adobe bricks10.1016/j.jclepro.2015.09.016 ↗
12. Lime stabilization of clay minerals and soils10.1016/0013-7952(96)00028-2 ↗
13. Oti · 2010
14. S.K. Dash, Hussain, M. J. J. O. M. I. C. E. (2011) Lime stabilization of soils: reappraisal. 24, 707-714.10.1061/(ASCE)MT.1943-5533.0000431 ↗
15. The use of stabilised Spanish clay soil for sustainable construction materials10.1016/j.enggeo.2012.02.010 ↗
16. M. Al-Mukhtar, A. Lasledj, Alcover, J.-F. J. A. C. S. (2010) Behaviour and mineralogy changes in lime-treated expansive soil at 20 C. 50, 191-198.10.1016/j.clay.2010.07.023 ↗
17. Optimum lime content identification for lime-stabilised rammed earth10.1016/j.conbuildmat.2013.11.077 ↗
18. Earth concrete (2018) Stabilization revisited10.1016/j.cemconres.2017.02.035 ↗
19. BS 1377-2: 1990 Methods of test for soils for civil engineering purposes. Classification tests, BSI UK.
20. EN 933-1:2012 Tests for geometrical properties of aggregates. Determination of particle size distribution. Sieving method. CEN. Eupean Norm.
21. EN 459-1:2010 Building lime Part 1: Definitions, specifications and conformity criteria. CEN. Eupean Norm.
22. S. Dewaele, R. Ottenburgs, P. Van Oyen, W. Viaene, Prospection and Evaluation ofclay deposits in the Republic of Ireland In: Industrial minerals Resources, characteristics and applications. Ed. Degryse P, Elsen J, 13, 97-105, 2003.
23. EN ISO 17892-12:2018 Geotechnical investigation and testing - Laboratory testing of soil. Part 12: Determination of liquid and plastic limits. CEN. Eupean Norm.
24. EN 1015-18:2002 Methods of test for mortar for masonry. Part 18: Determination of water absorption coefficient due to capillary action of hardened mortar. CEN. Eupean Norm.
25. EN 772-11:2011 Methods of test for masonry units. Determination of water absorption of aggregate concrete, autoclaved aerated concrete, manufactured stone and natural stone masonry units due to capillary action and the initial rate of water absorption of clay masonry units. CEN. Eupean Norm.
26. EN ISO 12572:2016 Hygrothermal performance of building materials and products - Determination of water vapour transmission properties. CEN. Eupean Norm.
27. EN 12667:2001 Thermal performance of building materials and products - Determination of thermal resistance by means of guarded hot plate and heat flow meter methods - Products of high and medium thermal resistance. CEN. Eupean Norm.
28. LINGL (2018) Laboratory Report. Raw materials of Lagan Brick, Kingscourt. Unpublished.
29. O. Alelweet, S. Pavia, An Evaluation of the Feasibility of Several Industrial Wastes and Natural Materials as Precursors for the Production of Alkali Activated Materials. World Academy of Science, Engineering and Technology, Int. J. Civil Environ. Eng., 13 (12) 741-748. waset.org/Publication/10010965. ISNI: 0000000091950263, 2019.
30. UNE 41410:2008. Bloques de tierra comprimida para muros y tabiques. Definiciones, especificaciones y métodos de ensayo. Compressed earth blocs for walls and partitions. Definitions, specifications and test methods. Spanish Norm. AENOR.
31. Mineralogical changes during firing of calcium-rich brick clays
32. Maggetti, M., 1982. Phase analysis and its significance for technology and origin. Archaeological ceramics. Ed. J.S.Olin and A.D. Franklin 121-133.
33. Effect of lime and fly ash on swelling percentage and Atterberg limits of sulfate-bearing clay10.1016/j.clay.2016.09.019 ↗
34. Effect of lime stabilisation on the strength and microstructure of clay10.9790/1684-638794 ↗
35. T.C. De Brito Galvão, A. Elsharief, Simões, G. F. J. J. O. E. E. Effects of lime on permeability and compressibility of two tropical residual soils. 130, 881-885, 2004.10.1061/(ASCE)0733-9372(2004)130:8(881) ↗
36. J. Kinuthia, S. Wild, Jones, G. J. A. C. S. Effects of monovalent and divalent metal sulphates on consistency and compaction of lime-stabilised kaolinite. 14, 27-45, 1999.10.1016/S0169-1317(98)00046-5 ↗
37. Effect of lime on plasticity, compaction and compressive strength characteristics of synthetic low cohesive (CL) and high cohesive (CH) clayey soils
38. The effects of hydrated lime on the linear shrinkage, free swell and soil suction of the tropical clay soils10.15623/ijret.2018.0702016 ↗
39. R.L. Buhler, A.B. Cerato, Stabilization of Oklahoma expansive soils using lime and class C fly ash. Problematic Soils and Rocks and In Situ Characterization, 2007.10.1061/40906(225)1 ↗
40. Soil property criteria for rammed earth stabilization10.1061/(ASCE)0899-1561(2008)20:3(264) ↗
41. Thermal performance and fitness of glacial till for Rammed Earth construction
42. The selection of soils for unstabilised earth building: a normative review10.1016/j.conbuildmat.2005.08.006 ↗
43. H. Houben, H. Guillaud, Earth Construction: A Comprehensive Guide. Intermediate Technology Publication, 1994.
44. Walker · 2005
45. Strength, durability and shrinkage characteristics of cement stabilised soil blocks10.1016/0958-9465(95)00019-9 ↗
46. CDI and CRATerre (1998) Compressed earth blocks: Standards – Technology series No.11, 1998.
47. XP P13-901 (2001) Compressed earth blocks for walls and partitions: definitions – Specifications – Test methods – Delivery acceptance conditions. Norme. French Standard.
48. HB 195: 2002 The Australian earth building handbook. Sydney. Published by Standards Australia International Ltd.
49. NZS 4298:1998 Materials and workmanship for earth buildings. Standards New Zealand.
50. J. Keable, R. Keable, Rammed earth structures: a code of practice. Publ. Intermediate Technology, 1996, 2011.10.3362/9781780440668.000 ↗
51. B. Little, T. Morton, Building with Earth in Scotland. Innovative Design and, 2001.
52. Compaction effect on the compressive strength and durability of stabilized earth blocks10.1016/j.conbuildmat.2017.12.074 ↗
53. SAZS 724: 2001. Standards Association Zimbabwe. Standard Code of Practice for Rammed Earth Structures. Harare: Standards Association of Zimbawbe, 2001.
54. IETcc. Obras de Fabrica, En: Prescripciones del Instituto Eduardo Torroja – PIET-70. Madrid: Instituto Eduardo Torroja de la Construccion y del Cemento, 1971.
55. McHenry · 1984
56. V. Rigassi, CRATerre-EAG: Compressed earth blocks, vol. 1: manual of production. Braunschweig, Allemagne: Friedrich Vieweg & Sohn, 1995.
57. E.W. Smith, G.S. Austin, Adobe, pressed-earth and rammed earth industries in New Mexico, Bulletin 159. Socorro, NM: New Mexico Bureau of Mines and Mineral Resources, 1996.10.58799/B-159 ↗
58. P. Walker, Maniatidis, V. J. N. B. T. G. A review of rammed earth construction. Department Of Architecture & Civil Engineering, U. O. B., UK, 2003.
59. ACI 1999. Building code requirements for masonry structures. American Concrete Institute, Detroit, MI., ISBN, 1929081022. Masonry Standards Joint Committee The masonry Society USA.
60. Lime fixation in clayey soils
61. Lime modification of clay soils for construction expediency10.1680/igeng.1997.29660 ↗
62. A critical appraisal of the role of clay mineralogy in lime stabilization10.1007/s40891-015-0009-3 ↗
63. Flexural tensile strength of construction elements made out of cement stabilized rammed earth10.1016/j.proeng.2015.07.049 ↗
64. Durability of lime stabilized earth blocks
65. Minke · 2006
66. J. McPadden, S. Pavía, An assessment of raw materials for earth construction in Co. Offaly, Ireland.Congreso Euro - Americano Rehabend. Patología de la Construcción, Tecnología de la Rehabilitación y Gestión del Patrimonio,Burgos,Ed. E.T.S. Ing. Caminos, Canales y Puertos, Santander, 2016.
67. Lime–and sand–stabilization of clayey materials from the Logone valley (Lake Chad basin) for their utilisation as building materials10.1016/j.jobe.2018.06.003 ↗
68. Microstructure and physical properties of lime-clayey adobe bricks10.1016/j.conbuildmat.2007.09.002 ↗
69. DIN 18945: 2013-08 Earth blocks - terms, requirements, test methods. German Standard.
70. Hygrothermal properties of earth bricks10.1016/j.enbuild.2014.05.024 ↗
71. The moisture buffering capacity of unfired clay masonry10.1016/j.buildenv.2014.09.027 ↗
72. Hygrothermal behaviour and relative humidity buffering of unfired and hydrated lime-stabilised clay composites in a Mediterranean climate10.1016/j.buildenv.2012.12.006 ↗
73. Mechanical and hygrothermal properties of compressed stabilized earth bricks (CSEB)
74. Conditions affecting the moisture buffering measurement performed on compressed earth blocks10.1016/j.buildenv.2014.01.009 ↗
75. Thermal performance of a selection of insulation materials suitable for historic buildings10.1016/j.buildenv.2015.07.033 ↗
76. L. Soudani, M. Woloszyn, A. Fabbri, J.-C. Morel, Grillet, A.-C. J. S. E. Energy evaluation of rammed earth walls using long term in-situ measurements. 141, 70-80, 2017.10.1016/j.solener.2016.11.002 ↗
77. Analysis of indoor performance of houses using rammed earth walls
78. Thermophysical properties of stabilised soil building blocks10.1016/0360-1323(94)00041-P ↗
79. Minke · 2012
80. Houben · 1994
81. Stabilization effects on the thermal conductivity and sorption behavior of earth bricks10.1016/j.conbuildmat.2018.02.063 ↗
82. EN 12524: 2000 Building materials and products – Hygrothermal properties – Tabulated design values. CEN. Eupean Norm.
83. Optimizing thermal and mechanical performance of compressed earth blocks (CEB)10.1016/j.conbuildmat.2015.12.024 ↗
84. Effect of mix design on compressed earth block strength10.1016/j.conbuildmat.2017.10.005 ↗
85. Mechanical and thermal performance characterisation of compressed earth blocks10.3390/en13112978 ↗
86. An experimental evaluation of prediction models for the mechanical behaviour of unreinforced, lime-mortar masonry under compression10.1016/j.jobe.2015.10.001 ↗
87. EN 1996-1-2: 2006 Eurocode 6. Design of masonry structures. Part 1-1. General rules for reinforced and unreinforced masonry structures. Part 2. Design, selection of materials and execution.
88. BS 5628-1: 2005 Code of practice, use of masonry. Structural use of unreinforced masonry, BSI UK.
89. Earth construction: lessons from the past for future eco-efficient construction10.1016/j.conbuildmat.2011.10.054 ↗
90. Effect of presence of salt on hygric performance of ceramic bricks10.1007/s11242-015-0461-5 ↗
91. Hygric performance of contemporary and historical ceramic bricks
92. Durability of rammed earth walls exposed for 20 years to natural weathering10.1016/j.buildenv.2008.07.001 ↗
93. Global distribution of clay-size minerals on land surface for biogeochemical and climatological studies10.1038/sdata.2017.103 ↗