journal article·2018-12

Influence of mix parameters on design of cold bituminous mix

Swayam Siddha Dash, Mahabir Panda

Publisher page

Abstract

Abstract In the absence of design uniformity, it is difficult to form reliable correlations between experimental results for Cold Bituminous Mixes (CBM) reported by different researchers/agencies/organizations. This paper presents a study on effects of various mix parameters such as aggregate gradation, method and level of compaction, variation in filler materials on performance of CBM. Dense (BC) and Gap (SMA) graded CBM were produced by both Marshall and gyratory method with varying level of compaction. Also, variations in filler materials (cement, lime, fly-ash) were done to evaluate the property of CBM. Finally, hot bituminous mixes were produced with same gradations (BC and SMA). A comparative study on test results has been made on basis of the Marshall Stability and air voids content of compacted mixes. It is observed that optimum residual bitumen content (ORBC) of cold mixes is not much affected by factors such as initial residual bitumen content (IRBC) and optimum total liquid content (OTLC). Rather, it mostly depends on the aggregate gradation. Considering all the selected parameters it is observed that only in case of gyratory compaction 3%–5% range of air voids can be achieved in CBM. Besides, though each and every parameter has contributed to increase the Marshall Stability of CBM, the most significant improvement as comparable with hot mixes is found to be caused by cement filler in comparison with other parameters. Also, higher load sustaining capacity of dense graded CBM is observed by its superior Marshall properties in comparison to gap graded CBM.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Asphalt Pavement Performance Evaluation · Infrastructure Maintenance and Monitoring · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (32)

Show source-provided references
1. Institute Manual Series No. 14 (AI MS 14) (1997). Asphalt cold mix manual, Third Edition, Part IV, Appendix F, USA, pp. 106–122.
2. Ministry of Road Transport and Highways (MORTH) (2013). Bituminous cold mix: Specifications for Road and Bridge Works, Fifth Revision, Section 500 (Cl.518), IRC, New Delhi, India, pp. 234–242.
3. Review and recommendation of cold asphalt emulsion mixtures (CAEMs) design
4. Effect of cement on emulsified asphalt mixtures10.1007/s11665-007-9095-2 ↗
5. A laboratory study on cold-mix, cold-lay emulsion mixtures
6. Cold Mix design of Semi dense bituminous concrete
7. Green Bituminous Asphalt relevant for highway and airfield pavement10.1016/j.conbuildmat.2011.12.065 ↗
8. Mechanical properties of an upgrading cold-mix asphalt using waste materials10.1061/(ASCE)MT.1943-5533.0000540 ↗
9. Investigating filler characteristics in upgrading cold bituminous emulsion mixtures10.2478/ijpeat-2013-0012 ↗
10. Performance of gap graded cold asphalt containing cement treated filler10.1016/j.conbuildmat.2014.07.081 ↗
11. Optimizing the mix design of cold bitumen emulsion mixtures using response surface methodology10.1016/j.conbuildmat.2015.12.073 ↗
12. Mechanical, durability and microstructure properties of Cold Asphalt Emulsion Mixtures with different types of filler10.1016/j.conbuildmat.2016.03.112 ↗
13. New developments with cold asphalt concrete binder course mixtures containing binary blended cementitious filler (BBCF)10.1016/j.conbuildmat.2016.07.114 ↗
14. High performance cold asphalt concrete mixture for binder course using alkali-activated binary blended cementitious filler10.1016/j.conbuildmat.2017.02.155 ↗
15. Goyer · 2012 · 1
16. Pundhir, N.K.S., 2012. Construction of rural road with cationic bitumen emulsion based cold mix technology. Workshop on Non-Conventional Materials/Technologies, Technical Papers, Central Road Research Institute, pp. 48–55.
17. Field experience of cold mix asphalt during 15 years
18. Bureau of Indian Standards (BIS) (1963). Methods of Test for Aggregates for Concrete Part-III: Specific Gravity, Density, Voids, Absorption, Bulking, IS 2386 (Part III), New Delhi, India.
19. American Society for Testing Materials (ASTM) (1995). Standard Test Method for Density of Hydraulic Cement, ASTM C 188, Philadelphia, USA.
20. Bureau of Indian Standards (BIS) (1978). Indian Standard Methods for Testing Tar and Bituminous Materials: Determination of Specific Gravity, IS 1202, New Delhi, India.
21. Bureau of Indian Standards (BIS) (1963). Methods of Test for Aggregates for Concrete Part-I: Particle size and shape, IS 2386 (Part I), New Delhi, India.
22. Bureau of Indian Standards (BIS) (1963). Methods of Test for Aggregates for Concrete Part-IV: Mechanical properties, IS 2386 (Part IV), New Delhi, India.
23. Bureau of Indian Standards (BIS) (2004). Bitumen emulsion for roads (cationic type) – Specification, Second Revision, IS 8887, New Delhi, India.
24. Bureau of Indian Standards (BIS) (1978). Indian Standard Methods for Testing Tar and Bituminous Materials: Determination of Penetration, IS 1203, New Delhi, India.
25. Bureau of Indian Standards (BIS) (1978). Indian Standard Methods for Testing Tar and Bituminous Materials: Determination of Ductility, IS 1208, New Delhi, India.
26. American Society for Testing Materials (ASTM) (1994). Standard Test Method for Saybolt Viscosity, ASTM D 88, Philadelphia, USA.
27. Bureau of Indian Standards (BIS) (1978). Indian Standard Methods for Testing Tar and Bituminous Materials: Determination of Softening Point, IS 1205, New Delhi, India.
28. American Society for Testing Materials (ASTM) · 2006
29. Indian Roads Congress (IRC) (2008). Tentative Specification for Stone Matrix Asphalt, IRC SP – 79, New Delhi, India.
30. American Society for Testing Materials (ASTM) · 1989
31. Brown, E.R., 1992. Experience with stone matrix asphalt in the United States. Report 93-04, National Center for Asphalt Technology, Auburn University, Alabama, US.
32. Mike Hemsley Jnr (2002). Cold Mix Design. AEMA Annual Conference, Bermuda.