Macrotexture modeling and experimental validation for pavement surface treatments
Source abstract
Abstract
Abstract Surface treatments (chip seals, single or double binder application, cape seals, slurry seals, microsurfacing, fog seals, reinforced seals) are widely used in flexible pavements maintenance and rehabilitation because of the reduced costs and the easiness of application. This paper focuses on the evaluation of surface texture of pavement surface treatments. A model was formalized and validated. It allows predicting as-built macrotexture, based on a few input factors (aggregate application rate, emulsion application rate, aggregate gradation). In the pursuit of model validation, an experimental investigation was designed and carried out. Outcomes of this theoretical and experimental study can benefit both practitioners and researchers.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Infrastructure Maintenance and Monitoring · Asphalt Pavement Performance Evaluation · Innovations in Concrete and Construction Materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (100+)
Show source-provided references
1. Measurement of international roughness index by using 3-axis accelerometers and GPS
2. A probabilistic programming model for blending aggregates10.1016/0307-904X(80)90192-4 ↗
3. Mean profile depth analysis of field and laboratory traffic-loaded chip seal surface treatments10.1080/10298436.2013.851790 ↗
4. S. Shuler, A. Lord, A. Epps-Martin, D. Hoyt, Manual for emulsion-based chip seals for pavement preservation, TRB Report No. NCHRP 680 (2011).10.17226/14421 ↗
5. State of California, Department of Transportation Office of Pavement Preservation Division of Maintenance, Maintenance Technical Advisory Guide (TAG) – Chapter 5, Chip Seals (2003).
6. S. Li, S. Noureldin, Y. Jiang, Y. Sun, Evaluation of Pavement Surface Friction Treatments, Joint Transportation Research Program, Indiana Department of Transportation and Purdue University, Report No.: FHWA/IN/JTRP-2012/04, West Lafayette, Indiana, 2012.10.5703/1288284314663 ↗
7. M.S. Islam, M. Hossain, Evaluation of lightweight aggregates in chip seal, in: Proc. of the 91st TRB Annual Meeting, Washington D.C. (USA), 2012.
8. Developing a macrotexture prediction model for chip seals10.1016/j.conbuildmat.2012.12.019 ↗
9. Transit New Zealand. Chipsealing in New Zealand. Road Controlling Authorities, Roading New Zealand, Wellington, New Zealand, 2005 (ISBN 0-478-10562-2).
10. Texas Pavement Preservation Center, Newsletter Issue 25, Winter, 2012 ().
11. D. Gransberg, D.M. James, Chip seal best practices – a synthesis of highway practice. TRB Report No. NCHRP Synth., vol. 342, 2011.
12. Federal Highway Administration, Pavement Preservation Compendium, Publication No. FHWA-IF-03-21 2003.
13. Austroads Incorporated, Austroads Provisional Sprayed Seal Design Method- Revision 2000, Austroads Project No. N.T&E.9902. Austroads Publication No. AP-T09/01. © Austroads Inc., 2003.
14. W. Holtrop, Sprayed sealing practice in Australia, in: 1st International Sprayed Sealing Conference, Adelaide, South Australia, 27–29 July 2008.
15. J.M. Croteau, J.K. Davidson, G. Houston, Seal coat systems in Canada: performances and practice, in: Annual Conference of the Transportation Association of Canada. Calgary, Alberta, 2005.
16. M. Maher, C. Marshall, F. Harrison, K. Baumgaertner, Context sensitive roadway surfacing selection guide – appendix A: roadway surfacing options catalog, Publication No. FHWA-CFL/TD-05-004 2005.
17. A. Kucharek, Measuring the curing characteristics of chip sealing emulsions, in: Joint ARRA–ISSA–AEMA Meeting, Asphalt Emulsion Manufacturers Association and McAsphalt, 2007.
18. Nicholls · 2002
19. A. Alderson, Update of the Austroads Sprayed Seal Design Method. Austroads Technical Report AP-T68/06© Austroads Inc. 2006ISBN 1 921139 65 X, 2006.
20. E.G. Williams, Asphalt surface treatments for local roads and streets, Manual KTC-88-4, 1998.
21. Texas Department of Transportation, TxDOT, Seal Coat and Surface Treatment Manual, 2010.
22. D. Gransberg, J.B. Carlisle, Evaluate TXDOT chip seal binder performance using pavement management information system and field measurement data San Antonio district, OU Transportation Research Report, 2004.
23. A.M. Johnson, Best practice Handbook on Asphalt Pavement Maintenance, Report No. MN/RC-2000-04, 2000.
24. A. Yamada, Asphalt seal coat treatments, Report No. 9977 1201 – SDTDC, U.S. Department of Agriculture, Forest Service, Technology and Development Program, 1999.
25. G. Hicks, S.B. Seeds, D.G. Peshkin, Selecting a preventive maintenance treatment for flexible pavements, FHWA Publication Number: FHWA-IF-00-027, 2000.
26. Wisconsin Transportation Information Center, Seal Coating & Other Asphalt Surfaces, Wisconsin Transportation Bulletin No. 10, 1992.
27. J.M. Croteau, F. Chaignon, M.A. Thompson, Four-year performance review of North American and international fibre-reinforced membrane systems, in: 52nd Annual Conference of the CTAA, Niagara Falls, Ontario, 2007.
28. ASTM E965-96 Standard Test Method for Measuring Pavement Macrotexture Depth Using a Volumetric Technique, 2006.
29. Determination of seal coat deterioration using image processing methods10.1016/j.conbuildmat.2013.11.090 ↗
30. Quantifying seal coat surface condition using digital image processing based on information theory10.1080/1029843021000101693 ↗
31. Using a New Zealand performance specification to evaluate U.S. chip seal performance10.1061/(ASCE)0733-947X(2007)133:12(688) ↗
32. Using a multi-phase model to predict flushing of sprayed seal pavements International
33. Effects of construction-related factors on chip seal performance10.1016/j.conbuildmat.2012.04.096 ↗
34. D.H. Woodward, A.R. Woodside, H. Yacoob, S.J. Maguire, Smaller stone size surface dressings for high stone surface mixes, in: Int. Surface Friction Conference – Roads and Runways, Christchurch, New Zealand, 2005.
35. J.C. Nicholls, D.P. Frankland, The long term performance of a surface dressing trial on A413, Amersham, TRL Report 261, Crowthorne, 1997.
36. Changes of surface dressing texture as related to time and chipping size
37. New Zealand Transport Agency, Performance based specification for reseals, Notes for the Specification for Bituminous Reseals, 2002 ().
38. Field evaluation of asphalt film thickness as a design parameter in Superpave mix design
39. B.A. Chadboum, E.L. Skok, D.E. Newcomb, B.L. Crow, S. Spindler, The effect of voids in mineral aggregate (VMA) on hot-mix asphalt pavements, University of Minnesota, Report No. MN/RC- 2000-13, 1999.
40. F.L. Roberts, P.S. Kandhal, E.R. Brown, D. Lee, T.W. Kennedy, Hot-mix asphalt materials, mix design, and construction, NAPA Education Foundation, Lanham, Maryland, 1991.
41. J.W. Oliver, Prediction of the life of sprayed seals and the effect of climate, durability and seal size, in: 6th International Conference on Managing Pavements, Brisbane, Queensland, 2004.
42. P.S. Kandhal, K.Y. Foo, R.B. Mallick, A critical review of VMA requirements in Superpave, National Center for Asphalt Technology, NCAT Report No. 98-1, 1998.
43. Department of Infrastructure, Energy and Resources, Tasmania Roadworks Specification R50 – Guide Notes for Bituminous Surfacing Specifications, 2011.
44. The relationship between voids, surface area, film thickness, and stability in bituminous paving mixtures
45. Read · 2003
46. New approaches for computing film thickness
47. F. Norme, Couches d’assis: Enrobé, à élevé. NF P98–140, NF, Paris, 1991.
48. P.S. Kandhal, S. Chakraborty, Evaluation of voids in the mineral aggregate for HMA paving mixtures, National Center for Asphalt Technology, NCAT Report No. 96-4, 1996.
49. East Valley Asphalt Committee, Hot asphalt mix criteria, 2006. (accessed July 10).
50. R. Roque, B.T. Birgisson, B. Nukunya, Evaluation of Superpave Criteria for VMA and Fine Aggregate Angularity, vol. 1, University of Florida, USA, 2002.
51. P.S. Khandal, K.Y. Foo, R.B. Mallick, A critical review of voids in mineral aggregate requirement in Superpave, NCAT Report No. 98-1, TRR 1609, 1998, pp. 21–27.10.3141/1609-03 ↗
52. F.L. Robert, P.S. Khandal, E.R. Brown, L. Dah-Yinn, T.W. Kennedy, Hot mix asphalt materials, mixture design and construction, second ed. National Asphalt Pavement Association, Research and Education Foundation, Lanham, Maryland, USA, 1996.
53. B.J. Coree, W.P. Hislop, A laboratory investigation into the effects of aggregate related factors of critical VMA in asphalt paving mixture. Iowa DOT Project TR-415, CTRE Management Project 98-20, Center for Transportation Research and Education, Iowa State University, 2000.
54. B. Birgisson, R. Roque, A. Varadhan, T. Thai, L. Jaiswal, Evaluation of thick open graded and bonded friction courses for Florida, Florida Department of Transportation, University of Florida, UF Project No.: 4504-968-12 (00026875), 2006.
55. B.J. Ajay Prakashm, R.S. Jaya, T.S. Umesha, A study on the variation of viscosity and film thickness of modified binders at various temperatures, in: Proc. of National Conference CRDCE13, SVIT, Vasad, 2013.
56. J.F. Goode, L.A. Lufsey, Voids, Permeability, Film Thickness vs. Asphalt Hardening, in: Proceedings, AAPT, vol. 34, 1965.
57. Analytical formulas for film thickness in compacted asphalt mixture
58. Validity of asphalt binder film thickness concept in hot-mix asphalt
59. P.D. Cenek, N.J. Jamieson, Sensitivity of in-service skid resistance performance of chipseal surfaces to aggregate and texture characteristic, in: Proc. International Surface Friction Conference, Christchurch, New Zealand, 2005.
60. S. Senadheera, R.W. Tock, M. Shabbir Hossain, B. Yazgan, S. Das, A testing and evaluation protocol to assess seal coat binder-aggregate compatibility, Report No. FHWA/TX-06/0-4362-1, 2006.
61. P.E. Krugler, C.K. Estakhri, C.M. Chang-Albitres, C.H. Sasser, Synthesis study on transverse variable asphalt application rates for seal coats, Report No. FHWA/TX-09/0-5833-1, 2009.
62. Washington state chip seal study
63. M. Zaman, D. Gransberg, R. Bulut, S. Commuri, D. Pittenger, Develop draft chip seal cover aggregate specification based on aims angularity, shape and texture test result, Report No. OTCREOS11.1-65-F, The University of Oklahoma, Office of Research Services, 2013.
64. Transportation Research Board, Progress Toward Performance-Graded Emulsified Asphalt Specifications, Transportation Research Circular E-C182, 2014.
65. A general method of design for seal coats and surface treatments
66. Austroads Austroads Test Method AG:PT/T051 – Average Least Dimension of Aggregate by Direct Measurement (Nominal Size 10 mm or Greater), 2005.
67. Jackson · 1963
68. F.J. Benson, B.M. Gallaway, Retention of Cover Stone by Asphalt Surface Treatments, vol. 133, Texas Engineering Experiment Station, Texas A&M University System, College Station, Bulletin, 1953, pp. 1–58.
69. Properties of geometrically cubical aggregates and its mixture design
70. R.L. Mchattie, Asphalt Surface Treatment Guide, Alaska Department of Transportation, 2001.
71. D.W. Janisch, F.S. Gaillard, Minnesota Seal Coat Handbook, Minnesota Department of Transportation, 1998.
72. Y.R. Kim, J. Lee, Quantifying the benefits of improved rolling of chip seals, Report No. FHWA/NC/2006-63, 2008.
73. Standard Specification for Road Work, Jabatan Kerja, Raya Malaysia, Kuala Lumpur, 2008.
74. D.R. Salomon (Assembled by), Asphalt Emulsion Technology, Transportation Research Circular E-C102 TRB, 2006.
75. M. Wade, R. Desombre, D. Peshkin, High volume/high speed asphalt roadway preventive maintenance surface treatments, South Dakota Department of Transportation, Report No. SD99-09, 2001.
76. National Cooperative Highway Research Program, NCHRP, Guide for mechanistic-empirical design of new and rehabilitated pavement structures – Part 3 – Design Analysis, 2004.
77. K.L. Smith, D. Peshkin, A. Wolters, J. Krstulovich, J. Moulthrop, C. Alvarad, Guidelines for the Preservation of High-Traffic-Volume Roadways, TRB, SHRP 2 Report S2-R26-RR-2, 2011.10.17226/14487 ↗
78. Binder Specification and Testing, Superpave Series SP-1, Asphalt Institute, Lexington, KY, 1997.
79. A.L. Epps, C.J. Glover, R. Barcena, A performance-graded binder specification for surface treatments, Texas Department of Transportation, Report No. FHWA/TX-02/1710-1, 2001.
80. L.F. Walubita, A. Epps Martin, C.J. Glover, A surface performance-graded (SPG) specification for surface treatment binders: development and initial validation, Texas Department of Transportation, Report No. FHWA/TX-05/0-1710-2, 2005.
81. State of California, Department of Transportation, Office of Pavement Preservation, Division of Maintenance, Maintenance Technical Advisory Guide – vol. I – Flexible Pavement Preservation – second ed., 2008.
82. F.G. Praticò, R. Vaiana, Permeable friction courses: area-based vs. line-based surface performance and indicators, in: INTER-NOISE 2013, the 42nd Int. Congress and Exposition on Noise Control Engineering, 15–18 September, Innsbruck, Austria, 2013 (ISBN: 978-163266267-5).
83. EN 13036-1, Road and airfield surface characteristics – test methods – Part 1: Measurement of pavement surface macrotexture depth using a volumetric patch technique, 2010.
84. UNI EN 12697-33, Bituminous mixtures – test methods for hot mix asphalt – Part 33: Specimen prepared by roller compactor, 2007.
85. EN 1428, Bitumen and bituminous binders – determination of water content in bituminous emulsions – azeotropic distillation method, 2012.
86. EN 1431, Bitumen and bituminous binders – determination of residual binder and oil distillate from bitumen emulsions by distillation, 2009.
87. EN 1429, Bitumen and bituminous binders, determination of residue on sieving of bituminous emulsions, and determination of storage stability by sieving, 2009.
88. EN 12847, Bitumen and bituminous binders – determination of settling tendency of bituminous emulsions, 2009.
89. EN 12850, Bitumen and bituminous binders – determination of the pH value of bitumen emulsions, 2004.
90. EN 1426, Bitumen and bituminous binders – determination of needle penetration, 2007.
91. EN 1427, Bitumen and bituminous binders – determination of the softening point – ring and ball method, 2007.
92. EN 12593, Bitumen and bituminous binders – determination of the Fraass breaking point, 2007.
93. EN 13398, Bitumen and bituminous binders – determination of the elastic recovery of modified bitumen, 2010.
94. EN 1097-2, Tests for mechanical and physical properties of aggregates – Part 2: Methods for the determination of resistance to fragmentation, 2010.
95. EN 15326, Bitumen and bituminous binders – measurement of density and specific gravity – capillary-stoppered pycnometer method, 2009.
96. EN 1097-8, Tests for mechanical and physical properties of aggregates – Part 8: Determination of the polished stone value, 2009.
97. EN 933-8, Tests for geometrical properties of aggregates – Part 8: Assessment of fines – sand equivalent test, 2012.
98. EN 1097-1, Tests for mechanical and physical properties of aggregates – Part 1: Determination of the resistance to wear (micro-Deval), 2011.
99. EN 933-4, Test for geometrical properties of aggregates – Part 4: Determination of particle shape – shape index, 2008.
100. CNR B.U.95/84, Determinazione dell’indice di forma, Norme Tecniche – Bollettino Ufficiale, 1984.