Utilization of untreated-phosphogypsum as filling and binding material in preparing grouting materials
Source abstract
Abstract
Abstract The industrial by-product phosphogypsum (PG) is one of the bulk solid wastes with the risk of environmental pollution. Recycling PG as filling and binding material in preparing grouting materials is not only an effective solution to the PG disposal, but also a new approach to replacing the conventional cement-based grouts that conforms to the sustainable development. The flowability, setting time and early strength are vital characteristics for the grouts. Water-resistance should also be considered in underground construction. This paper works on the workability of the PG-based grouting slurry and the mechanical strength of the hardened paste. The water-resistance and permeability of the grouts are investigated. XRD analysis and SEM observation are used to study the hydration products and the microstructure. Experimental results show that the increase of water/binder ratio and PG dosage leads to a longer setting time and a higher flowability. The grouts with superplasticizer dosage of
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Tailings Management and Properties · Rock Mechanics and Modeling · Concrete and Cement Materials Research
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (60)
Show source-provided references
1. Recycling phosphogypsum and construction demolition waste for cemented paste backfill and its environmental impact10.1016/j.jclepro.2018.03.131 ↗
2. Pollutant flows from a phosphogypsum disposal area to an estuarine environment: an insight from geochemical signatures10.1016/j.scitotenv.2016.02.070 ↗
3. Study on the performance of FGD gypsum-metakaolin-cement composite cementitious system10.1016/j.conbuildmat.2016.09.134 ↗
4. Research on the incorporation of untreated flue gas desulfurization gypsum into magnesium oxysulfate cement10.1016/j.jclepro.2020.122497 ↗
5. Influence of steel slag on mechanical properties and durability of concrete10.1016/j.conbuildmat.2013.06.044 ↗
6. The role of fly ash microsphere in the microstructure and macroscopic properties of high-strength concrete10.1016/j.cemconcomp.2017.07.021 ↗
7. Dynamic mechanical analysis of cement mortar prepared with recycled cathode ray tube (CRT) glass as fine aggregate10.1016/j.jclepro.2017.11.057 ↗
8. Influence of freeze-thaw cycles on capillary absorption and chloride penetration into concrete10.1016/j.cemconres.2017.05.018 ↗
9. Analysing the co-benefits: case of municipal sewage management at Surat, India10.1016/j.jclepro.2013.07.035 ↗
10. Phosphogypsum as a soil fertilizer: ecotoxicity of amended soil and elutriates to bacteria, invertebrates, algae and plants10.1016/j.jhazmat.2015.03.034 ↗
11. Utilization of solidified phosphogypsum as Portland cement retarder10.1007/s10163-012-0065-x ↗
12. Investigation on the application of steel slag–fly ash–phosphogypsum solidified material as road base material10.1016/j.jhazmat.2008.07.125 ↗
13. Phosphogypsum recycling in the building materials industry: assessment of the radon exhalation rate10.1016/j.jenvrad.2017.04.002 ↗
14. Utilization of waste phosphogypsum to prepare hydroxyapatite nanoparticles and its application towards removal of fluoride from aqueous solution10.1016/j.jhazmat.2012.09.066 ↗
15. Phosphogypsum as a construction material10.1016/j.jclepro.2017.08.049 ↗
16. Utilization of the black tea powder as multifunctional admixture for the hemihydrate gypsum10.1016/j.jclepro.2018.10.304 ↗
17. Distribution of some trace metals in Syrian phosphogypsum10.1016/j.apgeochem.2003.09.014 ↗
18. Potential use of phosphogypsum in concrete10.1016/S0008-8846(99)00107-6 ↗
19. Effect of modified phosphogypsum on the hydration properties of the phosphogypsum-based supersulfated cement10.1016/j.conbuildmat.2019.04.052 ↗
20. Some aspects of the durability of a phosphogypsum-lime-fly ash binder10.1016/0950-0618(95)00085-2 ↗
21. A perspective study on fly ash–lime–gypsum bricks and hollow blocks for low cost housing development10.1016/S0950-0618(02)00034-X ↗
22. Activation of fly ash–lime systems using calcined phosphogypsum10.1016/j.conbuildmat.2006.12.005 ↗
23. Utilization of phosphogypsum as raw and calcined material in manufacturing of building products10.1016/j.conbuildmat.2007.04.024 ↗
24. Study on lime–fly ash–phosphogypsum binder10.1016/j.conbuildmat.2006.07.010 ↗
25. Stabilized phosphogypsum: Class C fly ash: Portland type II cement composites for potential marine application10.1021/es010520+ ↗
26. Loess stabilization using cement, waste phosphogypsum, fly ash and quicklime for self-compacting rammed earth construction10.1016/j.conbuildmat.2019.117195 ↗
27. Experimental investigation of pressure grouting in sand10.1016/j.sandf.2016.02.001 ↗
28. Numerical and experimental investigation of pillar reinforcement with pressurized grouting and pre-stress10.1016/j.tust.2015.10.018 ↗
29. Study of cement-grout penetration into fractures under static and oscillatory conditions10.1016/j.tust.2014.08.003 ↗
30. On the viscous behavior of cement mixtures with clay, sand, lime and bottom ash for jet grouting10.1016/j.conbuildmat.2015.05.072 ↗
31. Freeze–thaw durability of cement-based geothermal grouting materials10.1016/j.conbuildmat.2014.01.051 ↗
32. Influence of cement grouts composition on the rheological behaviour10.1016/j.cemconres.2010.11.015 ↗
33. Investigations on the cementitious grouts containing supplementary cementitious materials10.1016/S0008-8846(02)00799-8 ↗
34. Harrison · 2013 · 175
35. Estimation of jet grouting parameters in Shahriar dam, Iran10.1016/S1674-5264(09)60228-3 ↗
36. In-line rheological measurements of cement grouts: effects of water/cement ratio and hydration10.1016/j.tust.2014.09.003 ↗
37. An investigation of rheological properties of cement-based grout mixed with rice husk ash (RHA)10.1016/j.conbuildmat.2015.05.025 ↗
38. Effect of sodium gluconate on dispersion of polycarboxylate superplasticizer with different grafting density in side chain10.1016/j.jiec.2017.06.032 ↗
39. A preliminary investigation of the properties of potassium magnesium phosphate cement-based grouts mixed with fly ash, water glass and bentonite10.1016/j.conbuildmat.2019.117501 ↗
40. Performance and hydration study of ultra-fine sulfoaluminate cement-based double liquid grouting material10.1016/j.conbuildmat.2016.11.135 ↗
41. ASTM C191, Standard Test Method for Time of Setting of Hydraulic Cement by Vicat Needle, ASTM Int. (2019).
42. ASTM C109/C109M, Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens), Chem. Anal. (2012).
43. An investigation into the effect of various chemical and physical treatments of a South African phosphogypsum to render it suitable as a set retarder for cement10.1016/S0008-8846(03)00036-X ↗
44. Multiproperty characterization of cleaner and energy-efficient vegetal concrete based on one-part geopolymer binder10.1016/j.jclepro.2019.119916 ↗
45. Experimental determination of the effective anionic charge density of polycarboxylate superplasticizers in cement pore solution10.1016/j.cemconres.2008.09.001 ↗
46. Study on the performance and mechanism of the liquid sodium aluminate accelerated agent (in Chinese)
47. Investigation on the potential of waste cooking oil as a grinding aid in Portland cement10.1016/j.jenvman.2016.10.027 ↗
48. Microstructural characterization of basalt fiber reinforced magnesium phosphate cement supplemented by silica fume10.1016/j.conbuildmat.2019.117795 ↗
49. Utilization of fly ash with silica fume and properties of Portland cement–fly ash–silica fume concrete10.1016/j.fuel.2009.10.003 ↗
50. Influence of curing conditions on properties of high calcium fly ash geopolymer containing Portland cement as additive10.1016/j.matdes.2013.07.018 ↗
51. Effect of silica fume on mechanical properties of high-strength concrete10.1016/S0958-9465(03)00017-9 ↗
52. Utilization of silica fume in concrete: review of durability properties10.1016/j.resconrec.2011.09.016 ↗
53. Optimisation of rheological parameters, induced bleeding, permeability and mechanical properties of supersulfated cement grouts10.1016/j.conbuildmat.2020.120078 ↗
54. Influence of silica fume replacement of cement on physical properties and resistance to sulfate attack, freezing and thawing, and alkali-silica reactivity
55. Influence of calcium compounds on the mechanical properties of fly ash geopolymer pastes10.1016/j.jhazmat.2008.12.121 ↗
56. Effect of triethanolamine hydrochloride on the performance of cement paste10.1016/j.conbuildmat.2018.12.124 ↗
57. Leakage behavior of toxic substances of naphthalene sulfonate-formaldehyde condensation from cement based materials10.1016/j.jenvman.2019.109934 ↗
58. Fresh and hardened properties of one-part fly ash-based geopolymer binders cured at room temperature: effect of slag and alkali activators10.1016/j.jclepro.2019.03.290 ↗
59. Performance and ITZ of pervious concrete modified by vinyl acetate and ethylene copolymer dispersible powder10.1016/j.conbuildmat.2019.117532 ↗
60. Effect of the combination of fly ash and silica fume on water resistance of magnesium–potassium phosphate cement10.1016/j.conbuildmat.2015.12.085 ↗