journal article·2011-02

Effect of fiber type and content on bleeding of steel fiber reinforced concrete

Tayfun Uygunoğlu

Publisher page

Abstract

Abstract In general, the addition of fibers in concrete mix significantly improves many of the engineering properties of concrete. On the other hand, steel fibers reduce the workability of concrete. This paper presents the effect of steel-fiber length (aspect ratio) and content on bleeding of steel fiber reinforced concrete (SFRC). Two different steel fiber types (both is hooked-end) were used at a ratio of 0% (control), 0.3%, 0.64%, 1% and 1.3% by volume. Slump, Ve-Be test, air content and unit weight were determined experimentally. Specimens were poured in the standard moulds and the bleeding water content was measured 30 min, 60 min, 90 min, 120 min, 150 min and 180 min after starting the test. The results indicated that the workability of concrete significantly reduced as the fiber dosage rate increases. This was assessed through standard slump test and Ve-Be consistometer test. The bleeding water content was increased by increase of the fiber volume fraction and fiber aspect ratio according to experimental results. Also, a bleeding coefficient value for SFRC made with and without steel fiber was proposed as a result of this study.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Innovations in Concrete and Construction Materials · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (28)

Show source-provided references
1. Bleeding of concrete as an ageing consolidation process10.1016/j.cemconres.2004.10.006 ↗
2. The influence of ground granulated blast furnace slag (GGBS) additions and time delay on the bleeding of concrete10.1016/S0958-9465(00)00024-X ↗
3. An experimental study on bleeding and channelling of cement paste and mortar10.1680/adcr.1998.10.1.1 ↗
4. Influence of concrete properties on bleeding and evaporation10.1016/j.cemconres.2003.07.004 ↗
5. Plastic shrinkage cracking of blended cement concretes in hot environments10.1680/macr.1999.51.4.241 ↗
6. Ravindrarajah RS, Bleeding of fresh concrete containing cement supplementary materials. In: The ninth east Asia-Pacific conference on structural engineering and construction, Bali, Indonesia; 16–18 December, 2003.
7. Experimental methodology to study plastic shrinkage cracks in high strength concrete
8. Effect of mix proportions on plastic shrinkage cracking of concrete in hot environments10.1016/S0950-0618(98)00019-1 ↗
9. Plastic shrinkage of steel fibre reinforced concrete10.1007/BF02473017 ↗
10. Investigation of microstructure and flexural behavior of steel–fiber reinforced concrete10.1617/s11527-007-9341-y ↗
11. Seismic behaviour and shear strength of framed joint using steel–fiber reinforced concrete10.1061/(ASCE)0733-9445(1992)118:2(341) ↗
12. Study of the fatigue performance and damage mechanism of steel fiber reinforced concrete
13. Fatigue behaviour of steel fiber reinforced concrete in uniaxial and biaxial compression
14. ACI 544. Design considerations for steel fiber reinforced concrete. Report 544.4R-88, American Concrete Institute, Farmington Hills, USA; 1988.
15. Properties of fiber reinforced concrete: workability, behavior under long-term loading, and air-void characteristics
16. EN 197-1/A1 Cement. Part 1: compositions and conformity criteria for common cements. Ankara, Turkey: Springer; 2005.
17. EN 1097-6, Tests for mechanical and physical properties of aggregates – part 6: determination of particle density and water absorption. TSE Ankara, Turkey; 2002 [in Turkish].
18. EN 933-4, Tests for geometrical properties of aggregates – part 4: determination of particle shape–shape index. TSE Ankara, Turkey; 2009 [in Turkish].
19. EN 1097-6, Tests for mechanical and physical properties of aggregates – part 2: methods for the determination of resistance to fragmentation. TSE Ankara, Turkey; 2000 [in Turkish].
20. TS 3530 EN 933-1, Tests for geometrical properties of agregates – part 1: determination of particle size distribution sieving method. TSE Ankara, Turkey; 1999 [in Turkish].
21. EN 12350-2. Testing fresh concrete – part 2: slump test. TSE Ankara, Turkey; 2002 [in Turkish].
22. EN 12350-3. Testing fresh concrete – part 3: vebe test. TSE Ankara, Turkey; 2002 [in Turkish].
23. ASTM Standard C232-92. Standard test methods for bleeding of concrete. American Society for Testing and Materials, ASTM Standards; 1992 [4.02:13942].
24. The influence of cement source and slag additions on the bleeding of concrete10.1016/0008-8846(95)00139-4 ↗
25. Settlement of fresh concrete-an effective stress model10.1680/macr.1988.40.142.3 ↗
26. Neville AM. Properties of concrete. Essex (UK): Longman; 1981.
27. Influence of mix proportions on rheology of cement grouts containing limestone powder10.1016/S0958-9465(02)00115-4 ↗
28. Properties of steel fiber reinforced fly ash concrete10.1016/j.conbuildmat.2007.11.002 ↗