Experimental behaviour of anchor bolts under pullout and relaxation tests
Source abstract
Abstract
Abstract The anchoring between a metallic component and a concrete block is an essential point in stability and durability of the structure. This joint has to transfer the deadweight of the structure and tensile, compressive and shearing loads created by the structure in service. This study focuses on the joint constituted of long anchor bolts cast-in-place. The anchor rods are prestressed in order to minimize the effects of fatigue stress. To design these anchors the long-term behaviour of concrete is not taken into account whereas the concrete creep and shrinkage involves a decrease in the initial prestress level. This paper presents experimental results of pull-out tests and mass-spring modelling of the joint is proposed. In this model the long-term behaviour of the joint is taken into account using the creep and shrinkage laws given in Eurocode 2. The modelling of the evolution in time of the rod prestress shows good agreement with the measurements obtained in relaxation tests.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Structural Behavior of Reinforced Concrete · Structural Load-Bearing Analysis · Fire effects on concrete materials
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (21)
Show source-provided references
1. Comité euro-International du béton. Fastenings to concrete and masonry structures – State of the art report. London: Thomas Telford Services Ltd.; 1994.
2. Breen JE, Eichinger E-M, Fuchs W. Anchoring to concrete: the new ACI Approach. In: International symposium on connections between steel and concrete: RILEM Publication, University of Stuttugart, Germany, September 2001. p. 10–2.
3. Steel Design Guide. Base plate and anchor rod design. AISC; 2006.
4. Comité euro-international du béton. Design of fastenings to concrete. London: Thomas Telford Services Ltd.; 1997.
5. ACI 349-79. Code requirements for nuclear safety related concrete structures. Detroit: American Concrete Institute; 1976.
6. Eurocode 3. Design of steel structure – Part 1–8: design of joints. Brussels: European Standards, CEN; 2005.
7. Towards a harmonized bond test
8. Size effect on the concrete cone pull-out load10.1023/A:1018685225459 ↗
9. Eligehausen R, Sawade G. A fracture mechanics based description of the pull-out behaviour of headed studs embedded in concrete structure. RILEM Report, London: Chapman and Hall; 1989.
10. Règles BAEL 91, révisées 99. Règles techniques de conception et de calcul des ouvrages et constructions en béton armé suivant la méthode des états limites. French Standards; 1999.
11. Ciampi V, Eligehausen R, Bertero VV, Popov EP. Analytical model for deformed-bar bond under generalized excitations. In: Trans IABSE Colloquium on advanced mechanics of reinforced concrete, Delft, Netherlands; 1981.
12. Development/splice strength of reinforced bars embedded in plain and fiber reinforced concrete
13. Bond behaviour between recycled aggregate concrete and steel rebars10.1016/j.conbuildmat.2005.08.008 ↗
14. Guo · 1997
15. CEB-FIB. CEB-FIB model code 1990. London: Thomas Thelford; 1993.
16. General creep-time equation10.1061/(ASCE)0899-1561(1998)10:2(118) ↗
17. Shrinkage and creep of high, medium and low strength concretes, including overloads
18. La macrostructure et le comportement du béton sous l’effet de sollicitations de longue durée10.1007/BF02475097 ↗
19. Equivalent axial stiffness of various components in bolted joints subjected to axial loading10.1016/j.finel.2006.12.013 ↗
20. Assemblage par éléments filetés
21. Eurocode 2. Design of concrete structures – Part 1 – 1: general rules and rules for buildings. Brussels: European Standards, CEN; 2003.