A comparative study of the bond strength of reinforcing steel in high-volume fly ash concrete and conventional concrete
Source abstract
Abstract
Abstract The production of Portland cement – the key ingredient in concrete – generates a significant amount of carbon dioxide. However, due to its incredible versatility, availability, and relatively low cost, concrete is the most consumed manmade material on the planet. One method of reducing concrete’s contribution to greenhouse gas emissions is the use of fly ash to replace a significant amount of the cement. An experimental investigation was conducted to compare the bond strength of reinforcing steel in high-volume fly ash concrete (HVFAC) – concrete with at least 50% of the cement replaced with fly ash – with conventional concrete (CC). This experimental program consisted of 12 pull-out specimens as well as 12 full-scale beams (three unconfined and three confined by transverse reinforcement for each concrete type). The pull-out specimens were based on RILEM recommendations, and the beam specimens were tested under a simply supported four-point loading condition. The CC test results served as a control and were used to evaluate the results from the HVFAC pull-out and beam specimen tests. Furthermore, a comparison was performed between results of this study and a bond database of CC specimens. These comparisons indicate that HVFAC beams possess comparable bond strength as CC beams.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Structural Behavior of Reinforced Concrete · Concrete Corrosion and Durability
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (25)
Show source-provided references
1. Marland G, Boden TA, Andres RJ. Global, regional, and national fossil fuel CO2 emissions. In trends: a compendium of data on global change. Carbon Dioxide Information Analysis Center, Oak Ridge National Laboratory, United States Department of Energy, Oak Ridge, Tenn., 2008 , Accessed date March 2012.
2. High-volume fly ash system: concrete solution for sustainable development
3. ASTM 618-94a. Standard specification for coal fly ash and raw or calcined natural pozzolan for use as a mineral admixture in portland cement concrete. In: Annual book of ASTM standards, vol. 04.02. Philadelphia, P.A.: American Society for Testing and Materials; 1995. p. 304–6.
4. ACI Committee 232 · 2003
5. Hydration in high-volume fly ash binders
6. Guide for selecting proportions for high-strength concrete with portland cement and fly ash
7. Superplasticized fly ash concrete for structural applications
8. Naik · 1989
9. Cross D, Stephens J, Vollmer J. (n.d). Structural applications of 100 percent fly ash concrete. Montana State University, Bozeman, MT.
10. Gopalakrishnan · 2005
11. ACI Committee 408 · 2003
12. Influence of corrosion and cracking on bond behavior and strength of reinforced concrete members
13. Fundamental tests on the effects of an epoxy coating on bond strength
14. Flexural response of concrete beams reinforced with FRP reinforcing bars
15. RILEM 7-II-128. RC6: bond test for reinforcing steel. 1. Pull-out test. RILEM technical recommendations for the testing and use of construction materials, E & FN Spon, U.K.; 1994. p. 102–5.
16. American Concrete Institute ACI Committee · 2008
17. ASTM A615/A615M · 2009
18. Powder additions to mitigate retardation in high-volume fly ash mixtures
19. Astm C 39/C 39M · 2012
20. Astm C 78/C 78M · 2010
21. Astm C 496/C 496M · 2011
22. American Association of State and Highway Transportation Officials (AASHTO). AASHTO LRFD Bridge Design Specifications, 4th ed., Washington, D.C.; 2007. p. 5-(72–84).
23. AS 3600 · 2009
24. CSA CAN3-A23.3 · 2004
25. Japan Society of Civil Engineers. Standard specification for concrete structure. JSCE No. 15, Tokyo; 2007. p. 154–9.