journal article·2014-08

Influence of the distribution and orientation of fibres in a reinforced concrete with waste fibres and powders

Nassim Sebaibi, Mahfoud Benzerzour, Nor Edine Abriak

Publisher page

Abstract

Abstract This paper focuses on the incorporation of the sub-product materials based on the fibres and powders as used in the reinforcement of a cement matrix. These reinforcements (fibres and powders) were obtained from recycling by crushing of a thermoset composite based on unsaturated polyester/glass fibre. The mechanical and physical properties of Waste Fibre and Powder Reinforced Concrete (WFPRC) were investigated after optimising the composite. Regarding mechanical properties, the study focused on the effect of the volume of fibres and powders on the flexural, the uniaxial tensile strength and on different mixing energy. Regarding physical properties, the porosity, the orientation and distribution of fibres in a cement matrix were investigated. The results show that the tensile strength of WFPRC increased when both fibres and powders were added. The mixing energy influence strongly the fibres/powder content, the porosity, the distribution and fibres orientation regarding the loading direction of composite. However, the fibres distribution is an important factor for explain efficiency the mechanical behaviour of WFPRC. Fibre-orientation measurement by two-dimensional (2D) image analysis of polished cross-sections is a rapid and highly efficient method for determining the fibre orientation distribution over large sample areas. The results confirm that the rheology and fibre/powder content of concrete has an important influence on the orientation of the fibres and therefore the mechanical behaviour of composite reinforced fibres. The mixture reinforced with 4.4%, 6.2% and 11.54% of fibre/powder present an orientation coefficient ranging from 0.3 and 0.35 which indicate that the orientation of WFPRC is in 3D because the number of fibres is the same in three planes and confirm the poor workability of samples reinforced fibres.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Innovations in Concrete and Construction Materials · Recycled Aggregate Concrete Performance

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (31)

Show source-provided references
1. Mechanical and physical properties of a cement matrix through the recycling of thermoset composites10.1016/j.conbuildmat.2012.02.048 ↗
2. Sebaibi · 2011
3. Markovic I. High-performance hybrid-fibre concrete: development and utilisation”, PhD Thesis, Delft University of Technology; 2006. ISBN 90-407-2621-3.
4. Gopalaratnam VS, Shah SP. Failure mechanisms and fracture of fiber reinforced concrete. In: Proceedings of fiber reinforced concrete symposium, November, Am. Conc. Inst. Baltimore MD; 1986. p. 1–26.
5. Lappa · 2007
6. Alfes C. Stahlfaserbeton – Neue Ansätze zur Qualitätssicherung. In: Fischer HB, editor. 16th International conference on building materials (IBAUSIL). Weimar, Germany, F.A. Finger-Institut für Baustoffkunde, Bauhaus Universität Weimar; 2006.
7. Wuest · 2007
8. Effects of time and shear energy on the rheological behaviour of oilwell cement slurries10.1016/S0008-8846(00)00416-6 ↗
9. Fibre orientation measurements in short-glass fibre composites, Part II: a quantitative error estimate of the 2D image analysis technique10.1016/S0266-3538(01)00106-3 ↗
10. Pull-out tests on steel fibres
11. Determination of fibre content, distribution and orientation in steel fibre concrete by X-ray technique
12. Ermittlung der Orientierung, Menge und Verteilung der Fasern in faserbewehrtem Beton10.1002/best.198800280 ↗
13. Grünewald S. Performance-based design of self-compacting fibre reinforced concrete. PhD Thesis. Delft University of Technology; 2004.10.1617/2912143624.030 ↗
14. Fibre orientation in shortfibre-reinforced thermoplastics. I. Contrast enhancement for image analysis10.1016/S0266-3538(98)00102-X ↗
15. Media Cybernetics LP. Optimas; 1999. 6.5.
16. Distribution and orientation of fibers in steel fibre reinforced concrete
17. Effectiveness of random fibres in composites10.1016/0008-8846(79)90063-2 ↗
18. Tensile strength of concrete affected by uniformly distributed and closely spaced short length of wire reinforcement
19. Stereology of concrete reinforced with short steel fibres
20. Simon A, Hajar Z, Lecointre D, Petitjean J. Realization of two road bridges with ultra-high-performance fibre reinforced concrete. In: 6th Int. symp. on high strength/high performance concrete, Leipzig; 2002. p. 753–68.
21. Grünewald S., Walraven JC. Erfahrungen mit Faserbetonen in den Niederlanden. In: 2. Leipziger Fachtagung, Innovationen im Bauwesen – Faserbeton, Leipzig; 2002. p. 237–51.
22. AFGC, Setra. Ultra high performance fibre-reinforced concretes interim recommendations, Working group BFUP, Reference Setra; 2002. F0211.
23. Toughness measurement – the need to think again10.1016/0958-9465(96)00021-2 ↗
24. Correlation of fiber dispersion, rheology and mechanical performance of FRCs10.1016/j.cemconcomp.2006.08.006 ↗
25. Non destructive monitoring of fiber orientation using AC-IS: an industrial-scale application10.1016/j.cemconres.2006.05.026 ↗
26. Spatial distribution of steel fibres in sprayed and cast concrete10.1680/macr.2003.55.3.225 ↗
27. Flowability of fibre-reinforced concrete and its effect on the mechanical properties of the material10.1016/j.conbuildmat.2010.02.025 ↗
28. Properties of concrete reinforced with different kinds of industrial waste fibre materials10.1016/j.conbuildmat.2009.06.017 ↗
29. Orientation factor and number of fibres at failure plane in ring-type steel fibre reinforced concrete10.1016/j.cemconres.2009.11.009 ↗
30. Mechanical properties of concrete-reinforced fibres and powders with crushed thermoset composites: the influence of fibre/matrix interaction10.1016/j.conbuildmat.2011.10.026 ↗
31. Crack growth resistance of hybrid fiber reinforced cement composites10.1016/S0958-9465(01)00043-9 ↗