Effect of plaster thickness on performance of external thermal insulation cladding systems (ETICS) in buildings
Source abstract
Abstract
Abstract In a properly designed and constructed building, insulating material contributes enormously to energy savings for the heating and cooling of buildings (about 60%). On the other hand, there is always the possibility of fire in buildings. Insulation materials mostly used in Turkey are expanded polystyrene foam (EPS), extruded polystyrene (XPS) and rock-wool (RW). RW is the best durable materials to fire, however it is expensive. EPS and XPS start to soften at low temperatures (about 80 °C). This is not only financial losses but also a contribution to CO 2 and global warming. For the study, tests conducted to determine combustion characteristics of insulation boards with different plaster thicknesses of 2, 4, 6 and 8 mm. They were exposed to ignition by a single flame test setup on the front surface. Moreover, the ignition time on the insulation boards was gradually increased from 0.5 min to 25 min. At the end of tests, burnt length and burnt volume of EPS boards behind plaster on the specimen surface were measured. Results showed that in practical engineering, all types of boards except for RW, must be used as insulating materials with at least 4 mm plaster for the lowest combustion and hazard. The optimum thickness is measured as 6 mm for all the coatings.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Structural Analysis of Composite Materials · Hygrothermal properties of building materials · Masonry and Concrete Structural Analysis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (26)
Show source-provided references
1. Thermal performance and cost effectiveness of wall insulation under Thai climate10.1016/j.enbuild.2011.10.025 ↗
2. Optimum insulation thickness of external walls for energy saving10.1016/S1359-4311(02)00209-0 ↗
3. Determination of the energy savings and the optimum insulation thickness in the four different insulated exterior walls10.1016/j.renene.2009.07.009 ↗
4. Optimization of insulation thickness for external walls using different energy sources10.1016/j.apenergy.2005.10.006 ↗
5. The environmental impact of optimum insulation thickness for external walls of buildings10.1016/j.buildenv.2006.10.054 ↗
6. Characterisation of smoke in expanded polystyrene combustion10.1016/S0141-3910(01)00168-9 ↗
7. Comparative environmental life cycle assessment of thermal insulation materials of buildings10.1016/j.enbuild.2014.05.057 ↗
8. Correlation study between flammability and the width of organicthermal insulation materials for building exterior walls10.1016/j.enbuild.2014.06.013 ↗
9. Performance criteria for the fire safe use of thermal insulation in buildings10.1016/j.conbuildmat.2015.10.014 ↗
10. Insulation materials for the building sector: a review and comparative analysis10.1016/j.rser.2016.05.045 ↗
11. Flammability and safety design of thermal insulation materials comprising PS foams and fire barrier materials10.1016/j.matdes.2016.03.080 ↗
12. Water-based flame retardant coating using nano-boehmite for expanded polystyrene (EPS) foam10.1016/j.porgcoat.2016.04.036 ↗
13. Thermal performance of a building envelope incorporating ETICS with vacuum insulation panels and EPS10.1016/j.enbuild.2014.06.053 ↗
14. Correlation between thermal conductivity and the thickness of selected insulation materials for building wall10.1016/j.enbuild.2006.06.002 ↗
15. Effect of insulation material thickness on thermal insulation
16. European Committee for Standardisation · 1996
17. TS 825 · 2008 · 6
18. TS EN ISO 11925-2 · 2010
19. EN 13494 · 2004
20. Experiment study on the ignition point of XPS foam plastics10.1016/j.proeng.2013.02.117 ↗
21. Experimental study on the characteristics of horizontal flame spread over XPS surface on plateau10.1016/j.jhazmat.2011.01.101 ↗
22. Thickness effect on flame spread characteristics of expanded polystyrene in different environments10.1177/0892705711411341 ↗
23. Emissions from the combustion of polystyrene, styrene and ethylbenzene under diverse conditions10.1016/j.fuel.2007.01.009 ↗
24. Review on the fire safety of exterior wall claddings in high-rise buildings in China10.1016/j.proeng.2013.08.112 ↗
25. Fire exposure to exterior walls and flame spread on combustible cladding10.1007/BF01293079 ↗
26. Thermal expansion of self-consolidating normal and lightweight aggregate concrete at elevated temperature10.1016/j.conbuildmat.2009.04.004 ↗