journal article·2016-11

Investigation on the mechanical behavior of polyester-scrap tire composites

Basim Abu-Jdayil, Abdel-Hamid I. Mourad, Atif Hussain

Publisher page

Abstract

Abstract An investigation of the mechanical properties of unsaturated polyester composites containing rubber waste particles is presented. The main objective of this work was to formulate and develop polyester-rubber composite as an insulating material with acceptable mechanical performance. To determine the effect of the rubber particles ratio on the compressive and tensile strengths and moduli of a polyester composite 8 different concentrations (i.e., 5%, 10%, 15%, 20%, 25%, 30%, 35% and 40% by volume) were considered. The experimental results revealed that mixing rubber particles with the polyester matrix decreased both the compressive and tensile strengths and moduli of the composite. As the rubber content increases, and due to its low hydrophilicity towards polyester resin, the degree of crosslinking between the rubber particles and polyester is reduced causing a noticeable reduction in the composite strengths. On the other side for all investigated rubber contents, the larger the particle size of rubber, the lower the composites strength and modulus of elasticity. This is due to the difficulty of dispersion of the large particles into the matrix resulting non homogenous distribution of the particles and less interfacial contact with the matrix and in turn degradation in the mechanical behavior. However, smaller rubber particles have more specific surface area that could improve the interfacial contact with the polyester matrix. The SEM micrographs indicated that voids within the composite matrix increased with the content and size of rubber particles. Though adding rubber particles reduces the mechanical properties, the prepared composites demonstrate superior mechanical tensile strengths (22.8–1.25 MPa) and compressive strength (79.5–8.42 MPa) if compared with the currently used insulating materials and comparable to some construction materials like the stone masonry.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Innovative concrete reinforcement materials · Structural Behavior of Reinforced Concrete · Concrete and Cement Materials Research

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (48)

Show source-provided references
1. Preparation and damping properties of (waste rubber powder)/hindered phenol composites10.1002/vnl.21361 ↗
2. Cocombustion of pulverized coal with waste plastic and tire rubber powders10.1021/ef101246q ↗
3. Concrete reinforcement with recycled fibers10.1061/(ASCE)0899-1561(2000)12:4(314) ↗
4. Application of recycled tyre cord in concrete for shrinkage crack control10.1007/BF00275355 ↗
5. D.N. Humphrey, Civil engineering applications of tire shreds, in: Proceedings of the Tire Industry Conference, 1999.
6. Application and feasibility of coal fly ash and scrap tire fiber as wood wall insulation supplements in residential buildings10.1016/j.resconrec.2008.07.004 ↗
7. Properties of concrete containing scrap-tire rubber – an overview10.1016/j.wasman.2004.01.006 ↗
8. Khosla · 1990
9. Design of highway embankments using tire chips10.1061/(ASCE)1090-0241(1997)123:4(295) ↗
10. D.N. Humphrey, W.P. Manion, Properties of tire chips for lightweight fill, in: Grouting, Soil Improvement and Geosynthetics, ASCE, 1992.
11. Engineering properties of tire/soil mixtures as a lightweight fill material10.1520/GTJ10355J ↗
12. Potential of scrap tire rubber as lightweight aggregate in flowable fill10.1016/S0956-053X(02)00160-5 ↗
13. Tire shreds as lightweight retaining wall backfill: active conditions10.1061/(ASCE)1090-0241(1998)124:11(1061) ↗
14. Use of shredded tires for lightweight fill
15. Mechanical properties of concrete with ground waste tire rubber10.1177/0361198196153200110 ↗
16. Evaluation of rubber-filled concrete and correlation between destructive and nondestructive testing results10.1520/CCA10447J ↗
17. Cement-based materials containing shredded scrap truck tyre rubber10.1016/0950-0618(96)00004-9 ↗
18. Ten-year performance evaluation of asphalt-rubber surface mixes10.3141/1681-02 ↗
19. J.O. Cano, E. Charania, The Phoenix experience using asphalt-rubber, in: Proceedings of National Seminar on Asphalt-Rubber, Kansas City, Missouri, 1989.
20. D.C. Esch, Construction and Benefits of Rubber-modified Asphalt Pavements, 1982.
21. J. Heerkens, A. Von Meier, Open-graded Rubberized Asphalt for Traffic Noise Reduction in Urban Areas, The Netherlands, 1989.
22. Effects of kenaf loading and 3-aminopropyltriethoxysilane coupling agent on the properties of polypropylene/waste tire dust/kenaf composites10.1177/0892705712475002 ↗
23. Utilization of recycled crumb rubber as fine aggregates in concrete mix design10.1016/j.conbuildmat.2012.12.054 ↗
24. Study of timber and concrete with rubber waste composite beams applied to bridges
25. Thermal behavior and performance evaluation of epoxy-based polymer concretes containing silicone rubber for use as runway repair materials10.1016/j.compstruct.2014.08.038 ↗
26. Effect of the addition of synthetic fibers to concrete thin slabs on plastic shrinkage cracking10.1016/j.conbuildmat.2010.04.041 ↗
27. Thermal insulation enhancement in concretes by adding waste PET and rubber pieces10.1016/j.conbuildmat.2008.09.014 ↗
28. Effect of ground tire rubber on structural, mechanical and thermal properties of flexible polyurethane foams10.1007/s13726-014-0301-4 ↗
29. Thermal and physical characteristics of polyester–scrap tire composites10.1016/j.conbuildmat.2015.12.180 ↗
30. Study on bentonite-unsaturated polyester composite materials10.1177/0731684402021017493 ↗
31. The properties of rubberized concretes10.1016/0008-8846(95)00014-3 ↗
32. A two-staged surface treatment to improve properties of rubber modified cement composites10.1016/j.conbuildmat.2012.11.014 ↗
33. New lightweight composite construction materials with low thermal conductivity10.1016/S0958-9465(00)00072-X ↗
34. Building houses with local materials: means to drastically reduce the environmental impact of construction10.1016/S0360-1323(00)00054-8 ↗
35. The effects of process parameters on the mechanical properties of die drawn polypropylene10.1016/j.polymertesting.2004.09.006 ↗
36. Effect of die drawing process on the mechanical behaviour of polypropylene
37. Use of ground rubber tires in Portland cement concrete
38. Rubber-tire particles as concrete aggregate10.1061/(ASCE)0899-1561(1993)5:4(478) ↗
39. Use of recycled rubber tires in concrete
40. Mechanical properties of particulate filled polymers10.1002/pc.750080208 ↗
41. Application of rice husk ash as fillers in polypropylene: effect of titanate, zirconate and silane coupling agents10.1016/0014-3057(95)00041-0 ↗
42. Waste ground rubber tire powder/thermoplastic vulcanizate blends: preparation, characterization, and compatibility
43. State of the art in thermal insulation materials and aims for future developments10.1016/j.enbuild.2004.05.006 ↗
44. Thermo-mechanical characteristics of thermally aged polyethylene/polypropylene blends10.1016/j.matdes.2009.07.031 ↗
45. Impact of some environmental conditions on the tensile, creep-recovery, relaxation, melting and crystallinity behaviour of UHMWPE GUR410-medical grade10.1016/j.matdes.2009.05.001 ↗
46. Effect of oil palm ash on the properties of polypropylene/recycled natural rubber gloves/oil palm ash composites10.15376/biores.10.1.1495-1505 ↗
47. Preparation and properties of nitrile rubber/montmorillonite nanocomposites via latex blending10.1007/s10853-006-0792-2 ↗
48. Investigation of debonding processes in particle-filled polymer materials by acoustic emission: Part I acoustic emission and debonding stress10.1023/A:1018684225784 ↗