A sustainable cold bonded lightweight PCM aggregate production: Its effects on concrete properties
Source abstract
Abstract
Abstract Due to the responsibility of building sector for a large portion of the energy consumed, it is necessary to prioritize the energy efficiency along whole lifecycle of a building. Designing buildings to provide maximum benefit from renewable energy sources, and reusing the by-products such as fly ash and blast furnace slag makes a significant difference with regard to sustainability and energy efficiency. In this study, artificial lightweight aggregates (LWAs) were produced utilizing phase change materials (PCMs) which are prominent in literature with their contribution to energy efficiency via their high thermal capacity. Supplementary cementitious materials (SCMs) were utilized as part of binder of LWAs. Pelletization method was used in production of LWAs. Effect of binder material composition and PCM amount to the production process and physical, mechanical and thermal properties of produced aggregates were investigated. As the amount of PCM increased, lighter aggregates with higher thermal capacities were obtained. The strength decreased significantly with use of PCM. Use of PCM at high amounts negatively affected the pelleting process as well. Concrete samples were produced using LWAs and tested to determine the effect of aggregates to concrete performance. The minimum compressive strength obtained was 33.9 MPa, which is accepted as satisfactory for many structural applications.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Phase Change Materials Research · Solar Energy Systems and Technologies · Adsorption and Cooling Systems
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (69)
Show source-provided references
1. United Nations, Resolution adopted by the General Assembly on 25 September 2015, General Assembly A/Res/70/1, Seventieth session, 21 October 2015, p. 14, 19.
2. Economic growth, energy consumption and sustainable development: the case of the Union for the Mediterranean countries10.1016/j.energy.2014.04.050 ↗
3. Application of phase change materials in gypsum boards to meetbuilding energy conservation goals10.1016/j.enbuild.2016.12.046 ↗
4. Decoupling analysis on energy consumption, embodied GHG emissions and economic growth — the case study of Macao10.1016/j.rser.2016.09.027 ↗
5. Towards sustainable-energy buildings10.1016/S0306-2619(03)00059-X ↗
6. Feasibility of energy savingrenovation measures in urban buildings: the impact of energy prices and theacceptable pay back time criterion10.1016/S0378-7788(01)00129-3 ↗
7. International Energy Agency (IEA) · 2016
8. U.S. Energy Information Administration · 2016 · 1
9. Influence of adding phase change materials on the physical and mechanical properties of cement mortars10.1016/j.conbuildmat.2016.09.119 ↗
10. A global review of energy consumption, CO2 emissions and policyin the residential sector (with an overview of the top ten CO2 emitting countries)10.1016/j.rser.2014.11.066 ↗
11. Operational vs. embodied emissions in buildings - a review of current trends10.1016/j.enbuild.2013.07.026 ↗
12. Lautsen · 2008
13. Passive cooling methods for energy efficient buildings with and without thermal energy storage – a review
14. A review on phase change material (PCM) for sustainable passive cooling in building envelopes10.1016/j.rser.2016.03.036 ↗
15. Mehling · 2008
16. Phase change materials (PCM) for cooling applications in buildings: a review10.1016/j.enbuild.2016.04.006 ↗
17. Raoux · 2009
18. Utilization of macro encapsulated phase change materials for the development of thermal energy storage and structural lightweight aggregate concrete10.1016/j.apenergy.2014.11.022 ↗
19. Potential applications of phase change materials in concrete technology10.1016/j.cemconcomp.2007.04.007 ↗
20. Incorporation of phase change materials in cementitious systems via fine lightweight aggregate10.1016/j.conbuildmat.2012.04.042 ↗
21. Control aspects of latent heat storage and recovery in concrete10.1016/S0927-0248(99)00128-2 ↗
22. Composite salt–hydrate concrete system for building energy storage10.1016/S0960-1481(99)00024-5 ↗
23. Investigation of the thermal performance of a passive solar test-room with wall latent heat storage10.1016/S0360-1323(97)00009-7 ↗
24. Latent heat storage in building materials10.1016/0378-7788(93)90040-2 ↗
25. Multifunctional analysis of innovative PCM-filled concretes10.1016/j.egypro.2017.03.010 ↗
26. Development of structural-functional integrated energy storage concrete with innovative macro-encapsulated PCM by hollow steel ball10.1016/j.apenergy.2016.10.072 ↗
27. Thermal behavior of a hybrid PCM/plaster: a numerical and experimental investigation10.1016/j.applthermaleng.2016.09.083 ↗
28. Integrating phase change materials into concrete through microencapsulation using cenospheres10.1016/j.cemconcomp.2017.04.001 ↗
29. Early-age temperature evolutions in concrete pavements containing microencapsulated phase change materials10.1016/j.conbuildmat.2017.04.150 ↗
30. Microencapsulated phase change materials for enhancing the thermal performance of Portland cement concrete and geopolymer concrete for passive building applications10.1016/j.enconman.2016.11.061 ↗
31. Numerical modelling and experimental studies of thermal behavior of building integrated thermal energy storage unit in a form of a ceiling panel10.1016/j.apenergy.2013.07.068 ↗
32. Micro-encapsulated phase change material (MPCM) slurries: characterization and building applications10.1016/j.rser.2017.04.001 ↗
33. Characterization of panels containing micro-encapsulated Phase Change Materials10.1016/j.enconman.2013.05.027 ↗
34. The behavior of self-compacting concrete containing micro-encapsulated phase change materials10.1016/j.cemconcomp.2009.08.002 ↗
35. Development of thermal energy storage concrete10.1016/j.cemconres.2003.10.022 ↗
36. Granular phase changing composites for thermal energy storage10.1016/j.solener.2004.04.022 ↗
37. Development of structural–functional integrated concrete with macro-encapsulated PCM for thermal energy storage10.1016/j.apenergy.2015.03.137 ↗
38. Artificial lightweight aggregates as utilization for future ashes – a case study10.1016/j.wasman.2011.08.017 ↗
39. Effects of lightweight fly ash aggregate properties on the behavior of lightweight concretes10.1016/j.jhazmat.2010.03.098 ↗
40. Characteristics of lightweight fly ash aggregates produced with different binders and heat treatments10.1016/j.cemconcomp.2010.09.007 ↗
41. Environmental friendly technology of cold-bonded bottom ash aggregate manufacture through chemical activation10.1016/j.jclepro.2010.06.006 ↗
42. Identification of design parameters influencing manufacture and properties of cold-bonded pond ash aggregate10.1016/j.matdes.2013.08.019 ↗
43. Manufacture and performance of cold bonded lightweight aggregate using alkaline activators for high performance concrete10.1016/j.conbuildmat.2012.04.032 ↗
44. Manufacture and performance of lightweight aggregate from municipal solid waste incinerator fly ash and reservoir sediment for self-consolidating lightweight concrete10.1016/j.cemconcomp.2012.07.004 ↗
45. Manufacture of artificial aggregate using MSWI bottom ash10.1016/j.wasman.2010.05.020 ↗
46. Properties of cold bonded quarry dust coarse aggregates and its use in concrete10.1016/j.cemconcomp.2015.05.005 ↗
47. Recycling of MSWI fly ash by means of cementitious double step coldbonding pelletization: technological assessment for the production of lightweight artificial aggregates10.1016/j.jhazmat.2015.06.018 ↗
48. Accelerated curing effects on the mechanical performance of cold bonded and sintered fly ash aggregate concrete10.1016/j.conbuildmat.2014.12.108 ↗
49. Artificial fly ash based aggregates properties influence on lightweight concrete performances10.1016/j.ceramint.2014.10.086 ↗
50. Utilization of fly ash by pelletization process; theory, application areas and research results10.1016/S0921-3449(00)00042-2 ↗
51. BASF Chemical Company · 2012 · 5
52. The stability of phase change materials in concrete10.1016/0927-0248(92)90113-4 ↗
53. BASF Chemical Company · 2010
54. Turkish Standard TS 802:2009, Design of Concrete Mixes, TSE.
55. European Standard EN 933-1:2012, Tests for Geometrical Properties of Aggregates – Part 1: Determination of Particle Size Distribution – Sieving Method, CEN.
56. European Standard EN 1097-6:2013, Tests for Mechanical and Physical Properties of Aggregates – Part 6: Determination of Particle Density and Water Absorption, CEN.
57. Comparison of ASTM saturation techniques for measuring the permeable porosity of concrete10.1016/j.cemconres.2004.09.017 ↗
58. Open porosity of cement pastes and their gas permeability
59. Measurement and statistics of single pellet mechanical strength of differently shaped catalysts10.1016/S0032-5910(00)00231-X ↗
60. A comparison of strength and elastic properties between conventional and lightweight structural concretes designed with expanded clay aggregates10.1016/j.conbuildmat.2015.10.080 ↗
61. Modulated differential scanning calorimetry10.1007/BF02546852 ↗
62. Colby College, Chemistry Lecture notes: https://www.colby.edu/chemistry/PChem/lab/DiffScanningCal.pdf.
63. DSC test error of phase change material (PCM) and its influence on the simulation of the PCM floor10.1016/j.renene.2015.07.085 ↗
64. European Standard EN 12390-7:2009-07, Testing Hardened Concrete – Part 7: Density of Hardened Concrete, CEN.
65. European Standard EN 13055:2016, Lightweight Aggregates, CEN.
66. Fly ash lightweight aggregates in high performance concrete10.1016/j.conbuildmat.2007.09.001 ↗
67. ASTM C125 – 18, Standard Terminology Relating to Concrete and Concrete Aggregates.
68. Determination of the PCM melting temperature range using DSC10.1016/j.tca.2014.09.004 ↗
69. European Standard EN 206:2013, Concrete – Specification, performance, production and conformity, CEN.