journal article·2019-07

Quantitative evaluation of elastic modulus of concrete with nanoidentation and homogenization method

Yaqiang Li, Yue Li, Rui Wang

Publisher page

Abstract

Abstract This paper aims to evaluate the elastic modulus of concrete with nanoidentation technique and homogenization method. In this paper, concrete is divided into two parts: coarse pore and matrix. It is assumed that matrix is composed of five phases: stone aggregate, ITZ-1 (interfacial transition zone around stone aggregate), sand, ITZ-2 (interfacial transition zone around sand) and paste. Based on the Ca/Si ratio change in interface region, the thicknesses of interfacial transition zone around stone and sand were determined, respectively. The elastic moduli of stone, ITZ-1, sand, ITZ-2 and paste were determined by nanoidentation technique. The volume fraction of each phase was determined by Lu & Torquato model. The elastic modulus of matrix was calculated by Self-Consistent Method. Then, combining with the porosity of coarse pore determined by hardened concrete pore structure analyzer, the elastic modulus of concrete could be obtained by Mori-Tanaka method. Through comparison, it is found that the error between the theoretical calculation value and the macroscopic test value is within 10%. Therefore, the effectiveness of theoretical prediction model proposed in this paper was verified.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Concrete Properties and Behavior · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (26)

Show source-provided references
1. Calcium silicate hydrate from dry to saturated state: structure, dynamics and mechanical properties10.1016/j.actamat.2013.12.016 ↗
2. The chemistry and structure of calcium (alumino) silicate hydrate: a study by XANES, ptychographic imaging, and wide-and small-angle scattering10.1016/j.cemconres.2018.09.008 ↗
3. Modification of incorporation and in-situ polymerization of aniline on the nano-structure and meso-structure of calcium silicate hydrates10.1016/j.conbuildmat.2018.06.141 ↗
4. Micromechanical analysis of heterogeneous structural materials10.1016/j.cemconcomp.2012.06.015 ↗
5. Macroscopic effective mechanical properties of porous dry concrete10.1016/j.cemconres.2012.10.012 ↗
6. Four-phase sphere modeling of effective bulk modulus of concrete10.1016/S0008-8846(99)00040-X ↗
7. Effective Young's modulus estimation of concrete10.1016/S0008-8846(99)00119-2 ↗
8. Influence of aggregate size, water cement ratio and age on the microstructure of the interfacial transition zone10.1016/S0008-8846(03)00205-9 ↗
9. Interfacial transition zone in concrete10.1016/1065-7355(95)90037-3 ↗
10. Interfacial zone percolation in cement-aggregate composites
11. Inhomogeneous interfacial transition zone model for the bulk modulus of mortar10.1016/S0008-8846(97)00086-0 ↗
12. Mondal · 2009 · 315
13. Micro-mechanical properties of individual phases in cement pastes under brine solution using nanoindentation and scanning electron microscopy10.4028/www.scientific.net/JNanoR.46.31 ↗
14. Evaluation of elastic modulus of cement paste corroded in bring solution with advanced homogenization method10.1016/j.conbuildmat.2017.09.133 ↗
15. A reliable technique to determine the local mechanical properties at the nanoscale for cementitious materials10.1016/j.cemconres.2007.07.001 ↗
16. The effect of two types of C-S-H on the elasticity of cement-based materials: results from nanoindentation and micromechanical modeling10.1016/S0008-8846(03)00230-8 ↗
17. Quantitative characterization and elastic properties of interfacial transition zone around coarse aggregate in concrete10.1007/s11595-017-1677-8 ↗
18. GB/T50081-2002, Standard for test method of mechanical properties on ordinary concrete. 2003.
19. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
20. An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments10.1557/JMR.1992.1564 ↗
21. Investigating the effect of the cement paste and transition zone on strength development of concrete containing nanosilica and silica fume10.1016/j.matdes.2015.03.024 ↗
22. Improving the microstructure of ITZ and reducing the permeability of concrete with various water/cement ratios using nano-silica
23. Berechnung der elastischen Konstanten des Vielkristalls aus den Konstanten des Einkristalls10.1007/BF01337948 ↗
24. Average stress in matrix and average elastic energy of materials with misfitting inclusions10.1016/0001-6160(73)90064-3 ↗
25. Analytical solution of the nearest surface spacing between neighboring binder grains in fresh cement paste
26. Analytical formulas for interfacial transition zone properties10.1016/S1065-7355(97)90016-X ↗