Flexural strength of plain and fibre-reinforced boroaluminosilicate geopolymer
Source abstract
Abstract
In the present work, flexural strength of plain and fibre-reinforced boroaluminosilicate geopolymers is studied. Traditional aluminosilicate geopolymers are produced by alkali activation of an aluminosilicate source. Alkali activator is normally made by mixing a high alkali solution (such as sodium hydroxide) and a silica-rich source (such as sodium silicate). Alkali activation of fly ash in this study, to fabricate boroaluminosilicate binders, was performed by mixtures of anhydrous borax and sodium hydroxide. Flexural strength of the specimens in unreinforced and reinforced conditions was measured by three-point bending. Reinforced specimens were prepared by using 2, 3 and 5 wt.% of steel fibres, with length and diameter of 30 and 0.5 mm respectively. The highest flexural strength of unreinforced specimens was 9.5 ± 0.4 MPa, with borax to NaOH solution weight ratio of 0.912 and alkali activator to fly ash weight ratio of 0.9. Reinforcing of this mixture by 5 wt.% of steel fibres resulted in the highest flexural strength, 11.8 ± 0.9 MPa. Maximum and minimum average increase of flexural strength of about 47% and 5% were achieved by adding 5 and 2 wt.% of steel fibres to some mixtures respectively. Results indicated the ability of these new classes of construction materials for using in flexural load-bearing sections in both unreinforced and reinforced situations.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Advanced ceramic materials synthesis
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (28)
Show source-provided references
1. High-strength geopolymer using fine high-calcium fly ash10.1061/(ASCE)MT.1943-5533.0000161 ↗
2. Durability of fly ash-based geopolymer structural concrete in the marine environment10.1061/(ASCE)MT.1943-5533.0000632 ↗
3. Impact of alkali silica reaction on fly ash-based geopolymer concrete10.1061/(ASCE)MT.1943-5533.0000579 ↗
4. Kinetics of geopolymerization: role of Al2O3 and SiO210.1016/j.cemconres.2007.01.003 ↗
5. Compressive strength and microstructural analysis of fly ash/palm oil fuel ash based geopolymer mortar10.1016/j.matdes.2014.03.037 ↗
6. Synthesis of sodium and potassium aluminogermanate inorganic polymers10.1016/j.matlet.2011.04.008 ↗
7. The phase evolution of phosphoric acid-based geopolymers at elevated temperatures10.1016/j.matlet.2011.08.043 ↗
8. Development of alkali activated borosilicate inorganic polymers (AABSIP)10.1016/j.jeurceramsoc.2011.02.021 ↗
9. Characteristics of boroaluminosilicate geopolymers10.1016/j.conbuildmat.2014.07.087 ↗
10. A feasibility study of strain hardening fiber reinforced fly ash-based geopolymer composites10.1016/j.conbuildmat.2014.02.005 ↗
11. Mechanical and durable behaviour of alkaline cement mortars reinforced with polypropylene fibres10.1016/S0008-8846(03)00222-9 ↗
12. Performance of an alkali-activated slag concrete reinforced with steel fibers10.1016/j.conbuildmat.2007.10.027 ↗
13. Preparation and mechanical properties of polypropylene fiber reinforced calcined kaolin-fly ash based geopolymer10.1007/s11771-009-0008-4 ↗
14. Novel fiber-reinforced composite materials based on sustainable geopolymer matrix10.1016/j.proeng.2011.11.2120 ↗
15. Short fiber reinforced geopolymer composites manufactured by extrusion10.1061/(ASCE)0899-1561(2005)17:6(624) ↗
16. Geopolymer extruded composites with incorporated fly ash and polyvinyl alcohol short fiber
17. Review of mechanical properties of short fibre reinforced geopolymer composites10.1016/j.conbuildmat.2013.01.026 ↗
18. Performance of refractory aluminosilicate particle/fiber-reinforced geopolymer composites10.1016/j.compositesb.2012.02.027 ↗
19. Synthesis and characterization of mechanical properties in cotton fiber-reinforced geopolymer composites10.1016/j.jascer.2013.01.002 ↗
20. Effects of high-temperature heat treatment on the mechanical properties of unidirectional carbon fiber reinforced geopolymer composites10.1016/j.ceramint.2010.02.012 ↗
21. Effects of fiber length on mechanical properties and fracture behavior of short carbon fiber reinforced geopolymer matrix composites10.1016/j.msea.2008.06.040 ↗
22. In situ crack growth observation and fracture behavior of short carbon fiber reinforced geopolymer matrix composites10.1016/j.msea.2009.12.004 ↗
23. Characterisation of cotton fibre-reinforced geopolymer composites10.1016/j.compositesb.2013.01.013 ↗
24. Deflection hardening behaviour of short fibre reinforced fly ash based geopolymer composites10.1016/j.matdes.2013.03.063 ↗
25. Utilization of sweet sorghum fiber to reinforce fly ash-based geopolymer10.1007/s10853-013-7950-0 ↗
26. Compressive strength of fly ash based geopolymer/glass fiber composite via filament winding
27. Behavior of PVA fiber-reinforced cementitious composites under static and impact flexural effects10.1061/(ASCE)MT.1943-5533.0000691 ↗
28. ASTM C293/C293M-10. Standard test method for flexural strength of concrete (using simple beam with center-point loading). Annual Book of ASTM Standards; 2010.