journal article·2012-03Open access

Evaluation of perforated steel plates as connection in glulam–concrete composite structures

José Luiz Miotto, Antonio Alves Dias

Abstract

Abstract This paper shows the results of an experimental investigation carried out on a connection element of glulam and concrete composite structures, through double-sided push-out shear tests. The connection system was composed of perforated steel plates glued with epoxy adhesive. Five specimens were made and tested under shear forces. This innovative connection system showed an average initial slip modulus equivalent to 339.4 kN/mm. In addition, the connection system was evaluated by means of numerical simulations and the software ANSYS was used for this purpose. The numerical simulations demonstrated good agreement with the experimental data, especially in the regime of elastic-linear behavior of materials.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Structural Load-Bearing Analysis · Geotechnical Engineering and Soil Stabilization · Wood Treatment and Properties

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (33)

Show source-provided references
1. Log-concrete composite bridge decks in Brazil: requirements and applications
2. Timber–concrete composite structures: a rational technique for bridges of vicinal roads
3. Behaviour of composite timber–concrete floors10.1061/(ASCE)0733-9445(1993)119:11(3111) ↗
4. Natterer J, Hamm J, Favre PA. Composite wood–concrete floors for multi-story buildings. In: Proceedings of the international wood engineering conference, New Orleans, USA: Lousiana State University; 1996. p. 431–5.
5. Composite concrete–timber structures10.1002/pse.126 ↗
6. Design and testing of a composite timber and concrete floor system
7. Bonded wood–concrete T-beams10.1061/JSDEAG.0002382 ↗
8. Timber–concrete composite structures
9. Gutkowski RM et al. Laboratory tests of composite wood–concrete beam and deck specimens. In: Proceedings of the 1st RILEM symposium on timber engineering, Cachan Cedex, France; 1999. p. 263–72.
10. Strength of inclined screw shear connections for timber and concrete composite construction
11. Pigozzo JC. Studies and applications of glued steel bars as connectors in timber–concrete composite slabs for bridge decks. PhD thesis, São Carlos School of Engineering, University of São Paulo; 2004 [in Portuguese].
12. Benítez MF. Concrete shear connectors. In: Proceedings of the 51st international convention of society of wood science and technology, concepción, Chile; 2008.
13. Nonlinear analysis of FRP–glulam–concrete beams with partial composite action10.1061/(ASCE)0733-9445(2001)127:8(967) ↗
14. Bathon L, Clouston P. Experimental and numerical results on semi-prestressed wood–concrete composite floor systems for long span applications. In: Proceedings of the 8th world conference on timber engineering, vol. 1, Lahti, Finland; 2004. p. 339–44.
15. Laboratory tests of composite wood–concrete beams10.1016/j.conbuildmat.2007.03.013 ↗
16. Persaud R. The structural behaviour of a composite timber and concrete floor system incorporating steel decking as permanent formwork. PhD thesis, Department of Engineering, University of Cambridge; 2006.
17. Symons D, Persaud R, Stanislaus, H. Slip modulus of inclined screws in timber–concrete floors. In: Proceedings of the institution of civil engineers, timber engineering, structures and buildings, vol. 163, no. SB4; 2010. p. 245–55.10.1680/stbu.2010.163.4.245 ↗
18. Pullout strength of axially loaded steel rods bonded in glulam at a 45 angle to the grain10.1590/S1516-14392009000400010 ↗
19. Influence of test specimen on experimental characterization of timber–concrete composite joints10.1016/j.conbuildmat.2009.12.036 ↗
20. EN 1994-1-1:2004. Eurocode 4: design of composite steel and concrete structures: general rules for buildings.
21. Gutkowski RM, Chen TM. Tests and analysis of mixed concrete–wood beams. In: Proceedings of the international wood engineering conference, vol. 12, New Orleans; 1996. p. 436–42.
22. EN 1995-1-1:2004. Eurocode 5: design of timber structures: general rules and rules for buildings.
23. Experimental analysis of Perfobond shear connection between steel and lightweight concrete10.1016/S0143-974X(03)00124-X ↗
24. Perforated shear connectors10.12989/scs.2002.2.1.051 ↗
25. NBR 6118: Design of concrete structures. Rio de Janeiro: ABNT; 2003 [in Portuguese].
26. Weaver CA. Behavior of FRP-reinforced glulam–concrete composite bridge girders. Master of Science thesis, The Graduate School, The University of Maine; 2002.
27. Willam KJ, Warnke ED. Constitutive model for the triaxial behavior of concrete. In: Proceedings of the international association for bridge and structural engineering, vol. 19, Bergamo, Italy; 1975. p. 174.
28. Flores ES, Rioseco CA, Matamal AV. Calibración del modelo de Hill modificado para el Pino Radiata chileno en conexiones de cizalle doble sometidas a compresión paralela. In: Proceedings of the 2nd Jornadas Chilenas de Estructuras de Madera, Santiago, Chile; 2007.
29. Molina JC. Analysis of the dynamic behavior of the connectors formed by bonded-in steel rods for log-concrete composite deck bridges. PhD thesis, São Carlos School of Engineering, University of São Paulo; 2008 [in Portuguese].
30. NBR 7190: Design of timber structures. Rio de Janeiro: ABNT; 1997 [in Portuguese].
31. Caracterização elástica da madeira de Eucalipto Citriodora
32. Dias AMPG. Mechanical behavior of timber–concrete joints. PhD thesis, University of Coimbra; 2005.
33. Ceccotti A et al. On the design of timber–concrete composite beams according to the new versions of Eurocode 5. In: Proceedings of the 35th meeting of the working commission W18 – timber structure, Japan; 2002.