journal article·2016-10

Effect of the substitution of cement by limestone filler on the rheological behaviour and shrinkage of microconcretes

Christian Varhen, Isabela Dilonardo, Roberto Cesar de Oliveira Romano, Rafael Giuliano Pileggi, Antonio Domingues de Figueiredo

Publisher page

Abstract

Abstract This study analyses the impact of substituting limestone fillers for cement on the rheological behaviour and drying shrinkage of microconcretes that are used for repair coatings. Three microconcretes were formulated with limestone filler contents of 80%, 60% and 20% by weight in relation of the total fines (cement and limestone filler). The total fines and water contents were kept constant in all of the formulations result in mixtures with similar volume of paste. The rheological behaviours of the mixtures were evaluated using a rheometer with planetary motion. The specimens were then moulded for mechanical characterisation and to measure the drying shrinkage. The porosity of the pastes was also evaluated using the mercury intrusion porosimetry (MIP). Rheological properties such as the yield stress and viscosity were influenced by the amount of cement that was replaced by fillers. Larger volumes of filler in the paste produced lower yield stresses and, consequently, higher slump values were obtained. However, the plastic viscosity increased with the filler content. In the hardened state, greater substitutions of cement by fillers decreased the drying shrinkage. This will cause lower differential shrinkage between the repair material and the existing substrate, generating lower tensile stresses in the repair material (repair coating) and therefore less potential for cracking of this. The experimental shrinkage results were compared to values that were obtained by the ACI 209, CEB-FIP90, B3 and GL2000 shrinkage prediction models. The models were found to overestimate the amount of shrinkage with increased substitution of cement by filler in the paste. Therefore, these models should be calibrated considering other factors such as the quantity of filler used in cement replacement. That consideration could optimize the use of these models in the design stage to verify if the values of expected shrinkage are within usually accepted limits for this application.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Concrete and Cement Materials Research · Concrete Properties and Behavior · Innovative concrete reinforcement materials

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (53)

Show source-provided references
1. H.-D. Beushausen, Long-term performance of bonded concrete overlays subjected to differential shrinkage, 2005.10.1016/j.cemconres.2006.05.027 ↗
2. Evaluation of the effects of drying shrinkage on the behavior of concrete structures strengthened by overlays10.1016/j.cemconres.2012.06.001 ↗
3. J. Carlswärd, Shrinkage cracking of steel fibre reinforced self compacting concrete overlays, test methods and theoretical modeling (Doctoral thesis), lulea university of technology Sweden, 2006.
4. Idiart · 2009
5. Strength and drying shrinkage properties of self-compacting concretes incorporating multi-system blended mineral admixtures10.1016/j.conbuildmat.2010.04.015 ↗
6. Influence of limestone filler and viscosity-modifying admixture on the shrinkage of self-compacting concrete10.1016/j.cemconres.2012.01.001 ↗
7. Influence of key parameters on drying shrinkage of cementitious materials10.1016/S0008-8846(99)00156-8 ↗
8. Shrinkage and creep of SCC – The influence of paste volume and binder composition10.1016/j.conbuildmat.2010.11.019 ↗
9. Influence of paste volume on shrinkage cracking and fracture properties of self-compacting concrete10.1016/j.cemconcomp.2007.03.010 ↗
10. The effect of coarse aggregate content and size on the age at cracking of bonded concrete overlays subjected to restrained deformation10.1016/j.conbuildmat.2014.06.056 ↗
11. A study on creep and drying shrinkage of high performance concrete10.1016/S0008-8846(01)00539-7 ↗
12. Shrinkage characteristics of alkali-activated fly ash/slag paste and mortar at early ages10.1016/j.cemconcomp.2014.07.007 ↗
13. Drying shrinkage of cement-based materials under conditions of constant temperature and varying humidity10.1016/S1006-1266(07)60119-9 ↗
14. Performance of self-compacting concrete containing fly ash10.1016/j.conbuildmat.2007.07.011 ↗
15. Compressive strength and shrinkage of mortar containing various amounts of mineral additions10.1016/j.conbuildmat.2011.03.055 ↗
16. Limestone fillers cement based composites: effects of blast furnace slags on fresh and hardened properties10.1016/j.conbuildmat.2013.10.076 ↗
17. Eco-friendly concretes with reduced water and cement content – Mix design principles and application in practice10.1016/j.conbuildmat.2013.12.066 ↗
18. B.L. Damineli, Conceitos para formulação de concretos com baixo consumo de ligantes: controle reológico, empacotamento e dispersão de partículas, 2013.
19. The influence of mineral admixtures on the rheology of cement paste and concrete10.1016/S0008-8846(00)00454-3 ↗
20. Rheological characterization of cement pastes with functional filler particles10.1016/j.cemconres.2014.06.010 ↗
21. Evaluation of the quality of fine materials and filler from crushed rocks in concrete production10.1016/j.conbuildmat.2013.10.029 ↗
22. Effect of limestone fillers the physic-mechanical properties of limestone concrete10.1016/j.phpro.2011.10.005 ↗
23. Fundamental modeling and experimental investigation of concrete carbonation
24. ACI Committee 209, 209.2R-08: Guide for Modeling and Calculating Shrinkage and Creep in Hardened Concrete, Technical Documents, 2008.
25. Comparison of theoretical and experimental shrinkage in concrete10.1016/j.conbuildmat.2014.06.050 ↗
26. Adsorption of gases in multimolecular layers10.1021/ja01269a023 ↗
27. The packing of particles10.1111/j.1151-2916.1930.tb16222.x ↗
28. I.R.d. Oliveira, A.R. Studart, R.G. Pileggi, V.C. Pandolfelli, Dispersão e empacotamento de partículas: Princípios e aplicações em processamento cerâmico, Fazendo Arte, São Paulo, 2000.
29. Impact of aggregate grading and air-entrainment on the properties of fresh and hardened mortars10.1016/j.conbuildmat.2015.02.067 ↗
30. Rheological methods for assessing the flow properties of mortar and related materials10.1016/0950-0618(94)90007-8 ↗
31. Effect of coarse aggregate characteristics on concrete rheology10.1016/j.conbuildmat.2010.09.035 ↗
32. Rheological properties of cementitious materials containing mineral admixtures10.1016/j.cemconres.2004.11.002 ↗
33. Development of a modified concrete rheometer to measure the rheological behavior of conventional and self-consolidating concretes10.1016/j.cemconcomp.2010.01.001 ↗
34. ABNT, NBR NM 67: Concreto – Determinação da consistência pelo abatimento do tronco de cone, Rio de Janeiro, 1998.
35. ABNT, NBR 13278: Argamassa para assentamento e revestimento de paredes e tetos – Determinação da densidade de massa e do teor de ar incorporado, Rio de Janeiro, 2005.
36. ASTM C01 Committee, ASTM C490/C490M-11e1: Practice for Use of Apparatus for the Determination of Length Change of Hardened Cement Paste, Mortar, and Concrete, ASTM International, West Conshohocken, PA, 2011.
37. Moisture in concrete subjected to different kinds of curing10.1007/BF02486397 ↗
38. Moisture transport and drying shrinkage properties of steel–fibre-reinforced-concrete10.1016/j.conbuildmat.2014.09.039 ↗
39. ABNT, NBR 5739: Concreto - Ensaios de compressão de corpos-de-prova cilíndricos, Rio de Janeiro, 2007.
40. Mercury porosimetry of hardened cement paste cured or stored at 97 C10.1016/0008-8846(74)90105-7 ↗
41. Rheology of fresh cement and concrete
42. S. Mindess, J.F. Young, D. Darwin, Concrete, 2003.
43. Aplicação do conceito de distância de separação interagregado (MPT) a concretos refratários de alta alumina10.1590/S0366-69131999000100004 ↗
44. Pumice powder as filler of self-compacting concrete10.1016/j.conbuildmat.2015.08.040 ↗
45. ABNT, NBR 12655: Concreto de cimento Portland – Preparo, controle, recebimento e aceitação – Procedimento, Rio de Janeiro, 2015.
46. Use of cement in concrete according to European standard EN 206-110.1016/j.hbrcj.2012.08.001 ↗
47. ACI Committee 325, Concrete overlays for pavement rehabilitation, American Concrete Institute, Farmington Hills, MI, 2006.
48. Measuring the eco-efficiency of cement use10.1016/j.cemconcomp.2010.07.009 ↗
49. Prediction equation of drying shrinkage of concrete based on composite model10.1016/j.cemconres.2004.08.002 ↗
50. Minimum cement content requirements: a must or a myth?10.1617/s11527-008-9436-0 ↗
51. Effects of drying conditions, admixtures and specimen size on shrinkage strains10.1016/j.cemconres.2004.11.005 ↗
52. Pore structure and influence of recycled aggregate concrete on drying shrinkage10.1155/2013/912412 ↗
53. Drying shrinkage and microstructure characteristics of mortar incorporating ground granulated blast furnace slag and shrinkage reducing admixture10.1016/j.conbuildmat.2015.05.103 ↗