Effect of chemical and thermal activation on the microstructural and mechanical properties of more sustainable UHPC
Source abstract
Abstract
This paper investigates the influence of the content of blast furnace slag (BFS) on the microstructural and mechanical properties of non-activated and activated ultra-high performance concrete (UHPC). Three volume-substitution rates of cement with BFS were explored (30% for UHPC2, 50% for UHPC3 and 80% for UHPC4) and two activation methods, chemical and thermal, were tested. Results show that with 30% of BFS, heterogeneous nucleation prevailed over dilution, accelerating the hydration reaction of cement and increasing the amount of C-S-H formed. C-S-H decreased the porosity of UHPC2 by 18% and 20% respectively at 3 and 90 days. The compressive strengths of UHPC1 (without BFS) and UHPC2 were very similar. For high BFS contents, the dilution effect prevailed and there was less portlandite, which decreased the amount of hydrated products, particularly at early age. As a result, the porosity of UHPC3 and UHPC4 was more than twofold higher than that of UHPC1.To boost the hydration reaction of blended UHPC with a high BFS content, KOH was added. The use of [KOH]3 significantly increased the amount of hydrated products, reducing the porosity of UHPC4 1.6-fold at 3 days and increasing its compressive strength by 42% at the same age. However, this activation mode was not enough to ensure the required compressive strength of UHPC1. Thermal activation at 90 °C for 2 days was therefore tested. Results showed the acceleration of the reaction of solid components, which increased the consumption of portlandite and hence the development of hydrated products. This resulted in improving the packing density of blended UHPC, decreasing its porosity and enhancing its compressive strength. In comparison with reference concrete at 90 days, the compressive strength of UHPC3-T increased by 7% and that of UHPC4 was 12.5% lower.
Source: openaire · Quality: candidate unverified · Source record ↗
Research context
OpenAlex topics: Concrete and Cement Materials Research · Innovative concrete reinforcement materials · Concrete Properties and Behavior
SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.
References (59)
Show source-provided references
1. E. Fehling, M. Schmidt, J. Walraven, T. Leutbecher, S. Frӧhlich, Ultra-high performance concrete UHPC: Fundamentals-Design-Examples, Wilhelm Ernst & Sohn, 10245 Berlin, Germany, 2014.10.1002/9783433604076 ↗
2. Mechanical and thermal evaluation of ultra high performance fiber reinforced concretes for engineering applications10.1016/j.conbuildmat.2011.06.023 ↗
3. Laneza · Micro Environ. Concr. Phys. Proced. · 2011 · 21 · 15910.1016/j.phpro.2011.10.024 ↗
4. Influence of palm oil fuel ash on ultimate flexural and uniaxial tensile strength of green ultra-high performance fiber reinforced cementitious composites10.1016/j.matdes.2013.08.094 ↗
5. Determination of optimized mix design and curing conditions of reactive powder concrete (RPC)10.1016/j.conbuildmat.2016.07.082 ↗
6. Pull-out behavior of steel fiber embedded in flowable RPC and ordinary mortar10.1016/j.conbuildmat.2014.11.037 ↗
7. Composition of reactive powder concretes10.1016/0008-8846(95)00144-2 ↗
8. Mechanical properties of ultra-high-performance fiber-reinforced concrete: a review10.1016/j.cemconcomp.2016.08.001 ↗
9. P. Mounanga, K. Cherkaoui, A. Khelidj, M. Courtial, M.-N. de Noirfontaine, F. Dunstetter, Extrudable Reactive Powder Concretes: Hydration, shrinkage and transfer properties. Europ. J. Environ. Civ. Eng. 16 (1) (2012) 1–20.10.1080/19648189.2012.681961 ↗
10. Effect of polycarboxylate and crushed quartz in UHPC: microstructural investigation10.1016/j.conbuildmat.2013.03.077 ↗
11. A review on ultra high performance concrete: Part II. Hydration, microstructure and properties10.1016/j.conbuildmat.2015.08.095 ↗
12. An investigation on blast-furnace slag as fine aggregate in alkali-activated slag mortars subjected to elevated temperatures10.1016/j.jclepro.2015.07.127 ↗
13. Utilization of fly ash and ground granulated blast furnace slag as an alternative silica source in reactive powder concrete10.1016/j.fuel.2008.03.005 ↗
14. Hassan, introducing an effective curing method for mortar containing high volume cementitious materials10.1016/j.conbuildmat.2015.12.100 ↗
15. Effect of curing regime and temperature on the compressive strength of cement-slag mortars10.1016/j.conbuildmat.2012.06.036 ↗
16. A review: The comparison between alkali-activated slag (Si+Ca) and metakaolin (Si+Al) cements10.1016/j.cemconres.2010.03.020 ↗
17. Mineral admixtures in mortars. Effect of inert materials on short-term hydration10.1016/S0008-8846(03)00183-2 ↗
18. Development of an eco-friendly Ultra-High Performance Concrete (UHPC) with efficient cement and mineral admixtures uses10.1016/j.cemconcomp.2014.09.024 ↗
19. P.E. Holthuizen, Chloride ingress of carbonated blast furnace slag cement mortars, Section of Materials and Environment (Master Thesis), Delft University of Technology, Netherlands, 2016.10.1007/978-3-319-59471-2_10 ↗
20. J. Zhou, G. Ye, K. van Breugel, Hydration process and pore structure of portland cement paste blended with blast furnace slag, in: Proceedings of the 6th International Symposium on Cement & Concrete, Canmet, 2006, pp. 1–7.10.1617/2351580028.085 ↗
21. Mechanical properties of reactive powder concrete containing mineral admixtures under different curing regimes10.1016/j.conbuildmat.2008.08.003 ↗
22. S. Gupta, Development of ultra-high performance concrete incorporating blend of slag and silica fume as cement replacement, Int. J. Civ. Struct. Eng. Res. 2 (1) (2014) 35–51.
23. The hydration and microstructure of ultra-high-strength concrete with cement–silica fume–slag binder10.1016/j.cemconcomp.2015.04.013 ↗
24. Effect of binder content on the performance of alkali-activated slag concretes10.1016/j.cemconres.2010.08.017 ↗
25. The effect of chemical activators on early strength of ordinary Portland cement-slag mortars10.1016/j.conbuildmat.2010.04.006 ↗
26. Early activation and properties of slag cement10.1016/0008-8846(90)90060-B ↗
27. Chemical acceleration of a neutral granulated blast-furnace slag activated by sodium carbonate10.1016/j.cemconres.2015.02.014 ↗
28. Very early-age reaction kinetics and microstructural development in alkali-activated slag10.1016/j.cemconcomp.2014.09.001 ↗
29. Alkali activation of a slag at ambient and elevated temperatures10.1016/j.cemconcomp.2011.08.003 ↗
30. W. Chen, Hydration of slag cement: Theory, modeling, and application, University of Twente (Doctoral Thesis), The Netherlands, 2007.
31. F. Sajedi, H. Abdul Razak, Effects of thermal and mechanical activation methods on compressive strength of ordinary Portland cement–slag mortar. Mater. & Des. 32 (2011) 984-995.10.1016/j.matdes.2010.08.038 ↗
32. F. Sajedi, H. Abdul Razak, Thermal activation of ordinary Portland cement–slag mortars. Mater. Des. 31 (2010) 4522–4527.10.1016/j.matdes.2010.04.011 ↗
33. Development of a light weight reactive powder concrete10.3151/jact.2.409 ↗
34. Activation of Algerian slag in mortars10.1016/j.conbuildmat.2007.10.012 ↗
35. The effect of w/b and temperature on the hydration and strength of blast furnace slag cements10.1016/j.conbuildmat.2015.11.001 ↗
36. Fraj, M. Bouasker, A. Khelidj, Mixture design and early age investigations of an environmentally friendly UHPC10.1016/j.conbuildmat.2017.12.107 ↗
37. Behaviour of concretes subjected to accelerated hardening (in French)
38. M.H. Kazemi-Kamyab, Autogenous shrinkage and hydration kinetics of Sh-UHPFRC under moderate to low temperature curing conditions (Thesis), EPFL, 2013.
39. P. Francisco, Déformations différées des bétons fibrés à ultra hautes performances soumis à un traitement thermique (Thesis), ENS Cachan, 2014 (in French).
40. Physico-chemical, morphological and thermal analysis for the combined pozzolanic activities of minerals additives10.1016/j.conbuildmat.2008.12.008 ↗
41. Physico-chemical study of cementitious materials based on binary and ternary binders
42. Properties and hydration of blended cements with steelmaking slag10.1016/j.cemconres.2007.03.008 ↗
43. Microstructure of composite cements containing blast-furnace slag and silica nano-particles subjected to elevated thermally treatment temperature10.1016/j.conbuildmat.2015.05.042 ↗
44. The hydration and microstructure of ultra high-strength concrete with cement-silica fume-slag binder10.1016/j.cemconcomp.2015.04.013 ↗
45. Microstructure of hardened complex binder pastes blended with slag
46. Influence of slag composition and temperature on the hydration and microstructure of slag blended cements
47. Ghosh · 2002
48. A.A. Ramezannianpour, Cement Replacement Materials: Properties, Durability, Sustainability, Springer-Verlag, Berlin Heidelberg, Germany, 2014.10.1007/978-3-642-36721-2 ↗
49. Shi · 2006
50. Effect of pore size distribution on drying shrinkage of alkali-activated slag concrete10.1016/S0008-8846(00)00327-6 ↗
51. Influence of aggregate and curing regime on the mechanical properties of ultra-high performance fibre reinforced concrete (UHPFRC)10.1016/j.conbuildmat.2008.11.012 ↗
52. Siddique · 2008
53. The properties of slag cement and its influence on the structure of the hardened cement paste10.1016/j.proeng.2016.07.202 ↗
54. Hydration of alkali-activated slag: comparison with ordinary Portland cement10.1680/adcr.2006.18.3.119 ↗
55. Physico-chemical, mechanical, microstructure and durability characteristics of alkali activated Egyptian slag10.1016/j.conbuildmat.2014.07.026 ↗
56. Temperature and activator effect on early-age reaction kinetics of alkali-activated slag binders10.1016/j.conbuildmat.2016.03.098 ↗
57. Alkali activation of mortars containing different replacement levels of ground granulated blast furnace slag10.1016/j.conbuildmat.2011.10.018 ↗
58. Effects of activator characteristics on the reaction product formation in slag binders activated using alkali silicate powder and NaOH10.1016/j.cemconcomp.2012.03.006 ↗
59. Mechanical properties of reactive powder concrete containing high volumes of ground granulated blast furnace slag10.1016/j.cemconcomp.2010.07.005 ↗