journal article·2018-10

Quasi-static in-plane testing of FRCM strengthened non-ductile reinforced concrete frames with masonry infills

N. Ismail, T. El-Maaddawy, N. Khattak

Publisher page

Abstract

Abstract Performance of fibre reinforced cementitious matrix (FRCM) strengthened non-ductile reinforced concrete frames with hollow concrete masonry infill (RCFMI) subjected to cyclic in-plane loading was experimentally assessed herein. A set of nine two-third scaled one bay-single story RCFMI prototypes were constructed that represented one bay of a low to medium height RCFMI building. Of these specimens, one frame was tested as-built without infill, one frame was tested as-built with infill, and the remainder were retrofitted using different FRCM schemes. The as-built tested frames served as control specimens and represented the baseline collapse risk associated to RCFMI buildings. Three different types of fibre grids (i.e. basalt, carbon, and glass) and three different FRCM configurations were used for retrofitting (i.e. full surface, diagonal bands with varying width). FRCM strengthened test frames exhibited a controlled failure mode characterised by distributed cracking in the FRCM matrix, without any signs of fibre slippage/rupture or deboning noted during the testing. Separation at the un-strengthened infill-frame contact region in FRCM strengthened frames was noted at a lateral drift of 0.4–0.6% and an applied lateral force of 1.2–2.0 times the strength of as-built tested frame. In general, test frames strengthened using diagonal bands with width equal to 1/6 infill diagonal length performed very similar to other configuration and therefore was deemed the most effective configuration. Carbon fabric had the highest strength compared to other fabrics used, but resulted in the lowest strength increment for the RCFMI, whereas Basalt-FRCM strengthened RCFMI exhibited the largest in-plane strength.
Source: openaire · Quality: candidate unverified · Source record ↗

Research context

OpenAlex topics: Masonry and Concrete Structural Analysis · Building materials and conservation · Structural Behavior of Reinforced Concrete

SciVX discovery tags are terminology-based. OpenAlex topics are source-provided classifications.

References (47)

Show source-provided references
1. A.C.I. Committee 549, Guide to Design and Construction of Externally Bonded Fabric-Reinforced Cementitious Matrix (FRCM) Systems for Repair and Strengthening Concrete and Masonry Structures (ACI-549.4-13), American Concrete Institute, 2013.
2. AC434, Acceptance criteria for masonry and concrete strengthening using fiber reinforced cementitious matrix (FRCM) composite systems, Whittier, CA: ICC Evaluation Service., 2013.
3. ASCE, Minimum Design Loads for Buildings and Other Structures ASCE-07 American Society of Civil Engineers, Reston VA USA, 2013.
4. Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement A615
5. ASTM Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens C39, ASTM International, West Conshohocken PA USA, 2017.
6. ASTM, Standard Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete C42, ASTM International, West Conshohocken PA USA, 2016.
7. ASTM, Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or 50-mm Cube Specimens) C109, ASTM International, West Conshohocken PA USA, 2016.
8. ASTM, Standard Test Methods for Sampling and Testing Concrete Masonry Units and Related Units C140, ASTM International, West Conshohocken PA USA, 2015.
9. ASTM, Standard Test Method for Slump of Hydraulic-Cement Concrete C143, ASTM International, West Conshohocken PA USA, 2015.
10. ASTM, Standard Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens C496, ASTM International, West Conshohocken PA USA, 2011.
11. ATC, Guidelines for Cyclic Seismic Testing of Components of Steel Structures for Buildings (ATC-24) Applied Technology Council, Redwood City California USA, 1992.
12. A qualification method for externally bonded Fibre Reinforced Cementitious Matrix (FRCM) strengthening systems10.1016/j.compositesb.2015.03.079 ↗
13. Fabric-reinforced cementitious matrix: A promising strengthening technique for concrete structures10.1016/j.conbuildmat.2016.11.125 ↗
14. Behavior and failure mechanisms of masonry-infilled RC frames (in low-rise buildings) subject to lateral loading10.1016/j.engstruct.2015.12.034 ↗
15. A macro-element modelling approach of infilled frame structures10.1016/j.compstruc.2014.07.008 ↗
16. Chopra · 1995
17. Effectiveness of plasters and textile reinforced mortars for strengthening clay masonry infill walls subjected to combined in-plane/out-of-plane actions10.1002/dama.201500673 ↗
18. Engineered cementitious composites for strengthening masonry infilled reinforced concrete frames10.1016/j.engstruct.2015.10.013 ↗
19. G. Della Corte, L. Fiorino, F.M. Mazzolani, Lateral-loading tests on a real RC building including masonry infill frames with and without FRP strengthening, J. Mater. Civil Eng. 20(6) (2008) 419–431. doi:10.1061/(ASCE)0899-1561(2008)20:6(419)10.1061/(ASCE)0899-1561(2008)20:6(419) ↗
20. Masonry infills and RC frames interaction: literature overview and state of the art of macromodeling approach10.1080/19648189.2014.996671 ↗
21. Building typologies and failure modes observed in the 2015 Gorkha (Nepal) earthquake10.5459/bnzsee.49.2.211-232 ↗
22. Interim Protocols for Determining Seismic Performance Characteristics of Structural and Nonstructural Components through Laboratory Testing FEMA-461, Federal Emergency
23. Steel frames with brickwork and concrete filling
24. Building typologies prevalent in Northern Pakistan and their performance during the 2015 Hindu Kush Earthquake10.1193/012116EQS022M ↗
25. Ismail · 2018
26. Cyclic out-of-plane behavior of slender clay brick masonry walls seismically strengthened using posttensioning10.1061/(ASCE)ST.1943-541X.0000565 ↗
27. The effective period and damping of a class of hysteretic structures10.1002/eqe.4290070302 ↗
28. Full-scale experimental study on masonry infilled RC moment-resisting frames under cyclic loads10.1016/j.engstruct.2015.02.008 ↗
29. Equivalent viscous damping equations for direct displacement based design10.1142/S1363246905002390 ↗
30. Seismic strengthening of masonry-infilled RC frames with TRM: Experimental study10.1061/(ASCE)CC.1943-5614.0000507 ↗
31. In-plane strengthening of clay brick unreinforced masonry wallettes using ECC shotcrete10.1016/j.engstruct.2014.01.043 ↗
32. Strengthening of infill masonry walls with FRP materials10.1061/(ASCE)CC.1943-5614.0000088 ↗
33. Anchorage systems for FRP strengthening of infill masonry structures
34. Experimental evaluation of masonry-infilled RC frames10.1061/(ASCE)0733-9445(1996)122:3(228) ↗
35. A new tool in the concrete and masonry repair
36. Load tests on a three-storey reinforced concrete building in Johannesburg
37. Analysis of the bond between fabric reinforced cementitious mortar (FRCM) strengthening systems and concrete10.1016/j.compositesb.2014.10.027 ↗
38. Quasi-static and pseudo-dynamic testing of infilled RC frames retrofitted with CFRP material10.1016/j.compositesb.2010.11.008 ↗
39. A capacity curve model for confined clay brick infills10.1007/s10518-015-9855-6 ↗
40. The captive- and short-column effects10.1193/1.1856533 ↗
41. Seismic improvement of infilled nonductile R frames with external mesh reinforcement and plster composite10.12989/eas.2015.8.3.761 ↗
42. Experimental and analytical stufy of masonry constructions reinforced with bed joints10.3139/120.110618 ↗
43. S.V. Polyakov, On the interaction between masonry filler walls and enclosing frame when loaded in the plane of the wall, in: construction in seismic regions, Earthquake Engineering, Earthquake Engineering Research Institute, San Francisco, CA USA (1960) pp. 36–42.
44. M. Selim, C. Okten, M. Ozkan, M.M. Gencoglu, Behavior of RC frames with infill walls strengthened by cement based composites, International Society of Offshore and Polar Engineers, in: Proceeding of the Twenty-fifth International Ocean and Polar Engineering Conference, 21-26 June (2015), Kona, Hawaii, USA.
45. Behavior of square infilled frames10.1061/JSDEAG.0001387 ↗
46. Lateral stiffness of infilled frames10.1061/JSDEAG.0000849 ↗
47. The strength of the brickwork